Summary of the content on the page No. 1
™
OWNER'S
MANUAL
MODEL NO.
45-03084
UNivERSAL T OW BEhiND TiLLER
• Assembly
CAUTION:
• Operation
Read Rules for
• Customer Responsibilities
Safe Operation
• Service and Adjustment
and Instructions
• Repair Parts
Carefully
the fastest way to purchase parts www.speedepart.com
Printed in U.S.A. FORM NO. 40566 (05/09/08)
Summary of the content on the page No. 2
TABLE OF CONTENTS SAFETY RULES ..........................................................3 SERVICE AND ADJUSTMENT ............................11-12 ASSEMBLY ...............................................................4-5 STORAGE .................................................................12 OPERATION .............................................................6-8 TROUBLESHOOTING ...............................................13 MAINTENANCE ...............................................
Summary of the content on the page No. 3
3
Summary of the content on the page No. 4
ASSEMBLY TO REMOvE UNiT FROM TO iNSTALL TE h TLLER i CARTON GAUGE WhEELS • Cut from top to bottom all four corners of the carton • Assemble Gauge Wheels onto the Rear Axle with the and lay panels flat. (See Fig. 1) extended end of Hub facing inward. Secure with the • Remove the lag screw that holds the floating hitch to Flat Washers and Cotter Pins which you removed from the packing skid. the axle during unpacking. (See fig. 2.) • Disassemble and discard carton's wood top and side support
Summary of the content on the page No. 5
ASSEMBLY TO iNSTALL (WhEEL) WEG i hTS TO TiLLER NOTE: Weights are not furnished with the Tiller. 30 lb. tractor wheel weights may be purchased to mount to the Tiller if extra weight is required. (Refer to the Operation section of this manual.) • Remove two Carriage Bolts and Nuts from each Tine Shield, located approximately 3-1/2" from the front edge. See fig. 4. • Place (Wheel) Weights on Tine Shield and secure with long Bolts and Nuts furnished with the Weights. See fig. 4. FiG. 4 5
Summary of the content on the page No. 6
OPERATION FG. i 5 RECOIL START HANDLE - used to start the engine SAFETY SWITCH - prevents engine from starting while tine clutch lever is engaged THROTTLE CONTROL - controls engine speed LiFT hANDLE - selects tilling or transport position by FUEL ShUT OFF - shuts of fuel to engine moving gage wheels CHOKE CONTROL - used when starting a cold engine TINE CLUTCH LEVER - starts and stops tine rotation DEPTH STAKE - controls tilling/cultivating depth FLOATING HITCH - telescoping hitch limits shock
Summary of the content on the page No. 7
OPERATION The operation of any tiller can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields before starting your tiller and while tilling. We recommend a wide vision safety mask for over the spectacles or standard safety glasses. • Repeat instructions in two preceding paragraphs until O h W TO USE YOUR TLLER i engine fires. When engine starts, move choke control gradually to RUN position. • Allow engine to warm u
Summary of the content on the page No. 8
OPERATION TRANSPORTING YOUR TILLER TRANSPORTING YOUR TILLER AROUND THE YARD AROUND THE YARD • Pull forward on lift handle until it locks in the up, • Pull forward on lift handle until it locks in the up, transport position. transport position. AROUND TOWN AROUND TOWN • Disconnect spark plug wire. • Disconnect spark plug wire. • Drain fuel tank. • Drain fuel tank. • Transport in upright position to prevent oil leakage. • Transport in upright position to prevent oil leakage. 8
Summary of the content on the page No. 9
CUSTOMER RESPONSIBILITIES Refer to the engine manual for instructions on engine maintenance. MAINTENANCE SCHEDULE Fill in dates as you complete regular service. Service Dates Check Engine Oil Level X Change Engine Oil X X* Service air cleaner precleaner X** Service air cleaner cartridge X** Replace spark plug X Clean cooling system X** Check valve clearance X Check for loose fasteners X Lubricate Tiller X Lubricate Tiller Transmission X * Change oi
Summary of the content on the page No. 10
CUSTOMER RESPONSIBILITIES ENGINE MAINTENANCE WARNING: Always stop engine and disconnect spark plug wire before cleaning, lubricating or before performing any repairs or maintenance. • Check oil level before each use and every 8 hours. • Maintain engine oil as instructed in the separate engine manual. • Service air cleaner every 25 hours under normal conditions. Clean every few hours under extremely dusty conditions. Poor engine performance and flooding usually indicates that the air cl
Summary of the content on the page No. 11
SERVICE AND ADJUSTMENTS WARNING: Shut off (disengage) the Tine Clutch Lever, the Tiller Engine and the Tractor Engine before making any repairs. TO REPLACE V-BELT Replace V-belt if it has been damaged considerably from slipping under heavy loads or if it show cracks or frayed edges. Refer to figures 11 and 12. IMPORTANT: Do not move or remove the belt guide. If the position of the belt guide is accidentally altered, return it to the correct setting (6-1/2" above the tine shield support
Summary of the content on the page No. 12
SERVICE AND ADJUSTMENTS WARNING: Shut off (disengage) the Tine SPARE TINE DRIVE BOLTS Clutch Lever, the Tiller Engine and the Tractor Engine before making any repairs. • The Tiller drive components are protected from damage by (shearable) Grade 5 hex bolts in the Tine Assemblies. The hex bolts drive the tines and hold them in the proper location. Should the Tine TINE CARE Assemblies strike or pick up a large hidden object or become jammed, the hex bolts will break and the • For best res
Summary of the content on the page No. 13
TROUBLEShOOTiNG Follow the instructions in the "Service & Storage" section of the Engine Manual when performing any work on the Engine. 13
Summary of the content on the page No. 14
REPAIR PARTS FOR MODEL 45-03084 UNIVERSAL TOW BEHIND TILLER 14 3 75 59 1 76 2 24 15 D 40 13 75 47 60 74 68 77 9 86 83 6 58 D 22 8 A 11 7 30 78 48 4 5 26 84 72 14 42 23 C 27 29 32 10 85 28 28 28 39 28 38 12 60 B 63 31 60 43 11 20 67 44 33 38 81 73 35 18 17 36 14 62 55 63 28 B 69 54 66 16 21 23 25 54 34 38 50 37 38 65 71 80 71 60 61 23 C 57 61 23 70 46 19 64 51 56 82 53 A 50 38 52 2
Summary of the content on the page No. 15
REPAIR PARTS FOR MODEL 45-03084 UNIVERSAL TOW BEHIND TILLER REF. PART NO. qTY . DESCRIPTION REF. PART NO. qTY . DESCRIPTION 1 40993 1 Engine (49 State) 44 HA20094 1 Tine & Hub Assembly - RH 40997 1 Engine (California) 45 HA20088 1 Tine & Hub Assembly - LH 2 48346 1 Guide - Belt 46 43054 4 Bolt, 3/8-16 x 2" 3 43085 4 Bolt, 5/16-18 x 1-1/2" Hex Head 47 47600 1 Bolt, Hex 5/16-24 x 1" 4 HA115321 1 Set Screw, 5/16-18 x 5/16" 48 HA5236 1 Pin, Hitch 5 HA11154 1 Key, Square 1/4" x 2" 49 43062 1 Bolt, 3
Summary of the content on the page No. 16
REPAIR PARTS FOR MODEL 45-03084 UNIVERSAL TOW BEHIND TILLER REF. PART NO. TY q . DESCRIPTION 1 HA20344 2 Dust Cap 2 43064 8 Locknut, 5/16-18 * 3 HA20123 2 Flange & Bearing Assy 4 HA20122 2 Gasket, Flange 5 43013 17 Locknut, 1/4-20 Hex * 6 HA20120 1 Drive Housing & Bearing Assy - LH 7 HA20136 1 Gasket, Drive Housing 8 HA20127 1 Tine Shaft Assy 9 HA20121 1 Drive Housing & Bearing Assy - RH 10 43866 15 Bolt, Hex 1/4-20 x 5/8" Grade 8 11 HA20125 2 Washer, Felt 12 HA20124 2 Seal, Rubber 13 HA20130 1
Summary of the content on the page No. 17
NOTES 17
Summary of the content on the page No. 18
NOTES 18
Summary of the content on the page No. 19
NOTES 19
Summary of the content on the page No. 20
the fastest way to purchase parts www.speedepart.com REPAIR PARTS Agri-Fab, Inc. 809 South Hamilton Sullivan, IL. 61951 217-728-8388 www.agri-fab.com © 2001 Agri-Fab, Inc.
