Summary of the content on the page No. 1
WASHING MACHINE
Owner’s Instructions
SW-903(P)/SWT90C1(P)/SWT90C2(P)
BEFORE USING THE WASHING MACHINE 1
PRECAUTIONS 1
CONTROL PANEL 2
DESCRIPTION AND CLEANING OF PART 2
WASHING PROCEDURE 3
To Wash 3
To Spin Dry 3
To Rinsing 4
Overflow rinse 4
Additional rinse 4
INSTALLATION 5
Location 5
Mounting the legs 5
Connecting the drain hose 5
Changing the position of the drain hose 5
LAUNDRY GUIDE 5
MAINTENANCE 6
TROUBLE SHOOTING 6
Before operating the washing machine, please read this manual
thoroughly
Summary of the content on the page No. 2
IF YOU NEED HELP. Do not hesitate to call your local Samsung Service Center. They will be pleased to help you. Be sure to give them your name, address, telephone number and the purpose of the call. SPECIFICATIONS DIMENSIONS SWT90C1(P)/SWT90C2(P) 820 x 524 x 1000 mm SW-903(P) 820 x 524 x 920 mm WT10S0(P)/WT10S1(P)/WT10S2(P) 820 x 524 x 993 mm 2 WATER PRESSURE 0.05~0.78 MPa(0.5 ~ 8.0kg . f/cm ) WEIGHT 36 kg EXTRACTION EFFICIENCY 50 % STANDARD QUANTITY OF WATER Low : 44l Middle : 56l
Summary of the content on the page No. 3
CONTROL PANEL BEFORE USING THE WASHING MACHINE CAUTIONS 0 • Remove the cap-hose • Be sure that the washer is grounded. 1.WASH TIMMER 15 3 from the drain hose. To avoid electrical shock,use a This is used to set the metal pipe for the ground 12 6 wash time, 1-15 minutes. 9 connection. But, don't ground the WASH TIMER • In the case of pump drained washer with gas pipes or telephone 2.CYCLE SELECTOR Wash/Rinse Wash washer, remove lines to avoid to dangers of explosion This is used to set the
Summary of the content on the page No. 4
DESCRIPTION AND /CLEANING OF PARTS CLEANING THE FILTER • Pull the overflow filter out and take up the filter by removing 3 screws as shown in figure. Wash the filter and washing tub. SPIN DRYER LID When you open this INNER LID lid while the spin basket is spinning,the spinning will be stopped by the brake DRAIN HOSE system. CLEANING THE FILTER SPIN DRYER BASKET (with pump) • Push the strainer(filter) out and take up the filter as shown in figure. POWER CORD Wash the filter and washing tub.
Summary of the content on the page No. 5
WASHING PROCEDURE A-type : SWT90C1(P)/SWT90C2(P)/WT10S0(P)/WT10S1(P)/WT10S2(P) B-type : SW-903(P) TO WASH (B-type) TO SPIN DRY TO WASH (A-type) 1. Before starting to wash, proceed as follows, 1. Before starting to wash, proceed as follows, 1. Transfer the clothes into the Connect the water supply hose and open Connect the water supply hose and open spin basket and arrange the the water tap. the water tap. clothes evenly. • Lay the drain hose down toward • Lay the drain hose down toward a sinkh
Summary of the content on the page No. 6
ADDITIONAL RINSE OVER FLOW RINSE (A-type) TO RINSING (A-type) Wash/Rinse Wash 1. Set the cycle selector KNOB to 1. Keep supplying 1 After rinsing you can select this Wash/Rinse Wash ‘WASH.RINSE’. water(adjust water course for more effective rinse Drain Rinse Drain (In the case of drain pressure to ensure (Don't just select this course Drain Rinse Drain that the amount of pump ‘WASH’) CYCLE SELECTOR CYCLE SELECTOR for rinse.) Load the laundry water supplied evenly into the spin basket.
Summary of the content on the page No. 7
INSTALLATION LAUNDRY GUIDE LOCATION CONNECTING THE DRAIN HOSE WASHING TIME Leave some space of After attaching the connector ring(a), insert the Water Level Low Middle High at least 15cm between the washing machine drain hose(b) in the draining direction. and the wall. 22 Pieces 29 Pieces 35 Pieces Sgurts (Synthetics) Place the washing machine on a sturdy flat a surface. b Under Shirts (Cotton) 38 Pieces 48 Pieces 58 Pieces If the washing machine is placed on an uneven or weak surface, noise or
Summary of the content on the page No. 8
AFTER OPERATION MAINTENANCE TROUBLE SHOOTING 1. Remove the power cord from the outlet. TO LOAD THE LAUNDRY INTO TROUBLE CHECK POINT 2. Take out the laundry. THE SPIN BASKET. The washing Check that the power cord is 3. Close the water tap and disconnect the water Press the laundry evenly and put the safety machine does properly connected to a power supply hose. cover into the spin basket as shown in the not work. outlet. Is there a power failure? 4. Clean the washing machine. figure. C
