Summary of the content on the page No. 1
Operation/Maintenance
Washer-Extractor
Cabinet Hardmount
B-Series Microcomputer
Variable-Speed
HC125BYV and SC125BYV
B004C
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)
Part No. F232215R1
www.comlaundry.com September 2008
Summary of the content on the page No. 2
Summary of the content on the page No. 3
Safety Information.............................................................................. 2 Table of Explanation of Safety Messages........................................................... 2 Important Safety Instructions ............................................................... 2 Contents Safety Decals ........................................................................................ 4 Operator Safety..........................................................................
Summary of the content on the page No. 4
Safety Information Explanation of Safety Messages Important Safety Instructions Precautionary statements (“DANGER,” “WARNING” WARNING and “CAUTION”), followed by specific instructions, are found in this manual and on machine decals. These To reduce the risk of fire, electric shock, precautions are intended for the personal safety of the serious injury or death to persons when operator, user, servicer and those maintaining the using your washer, follow these basic machine. precautions: W0
Summary of the content on the page No. 5
Safety Information 9. Do not install or store the washer where it will be 20. If supply cord is damaged, it must be replaced by exposed to water and/or weather. a special cord or assembly available from the manufacturer or its service agent. 10. Do not tamper with the controls. 21. Be sure water connections have a shut-off valve 11. Do not repair or replace any part of the washer, or and that fill hose connections are tight. CLOSE attempt any servicing unless specifically the shut-off val
Summary of the content on the page No. 6
Safety Information WARNING CAUTION This machine must be installed, adjusted, Be careful around the open door, and serviced by qualified electrical particularly when loading from a level maintenance personnel familiar with the below the door. Impact with door edges construction and operation of this type of can cause personal injury. SW025 machinery. They must also be familiar with the potential hazards involved. Failure to observe this warning may result in personal injury and/or equipment
Summary of the content on the page No. 7
Safety Information Do not bypass any safety devices in the machine. Operator Safety WARNING WARNING NEVER insert hands or objects into Never operate the machine with a basket until it has completely stopped. bypassed or disconnected balance Doing so could result in serious injury. system. Operating the machine with SW012 severe out-of-balance loads could result in personal injury and serious equipment To ensure the safety of machine operators, the damage. following maintenance checks mus
Summary of the content on the page No. 8
Introduction Harnessing Introduction Wiring harnesses are modular – harnesses common to The “B” electronic control is composed of the various configurations are similar, while those specific electronic control unit and the control fuse board with to a certain configuration can be added. There are wiring harness. Only an authorized person should look harnesses for inputs to the control unit, for outputs inside the machine. First TURN OFF POWER, open from the control power/output unit to t
Summary of the content on the page No. 9
Introduction Nameplate Location The nameplate is located at the rear of the machine and inside door. Always provide the machine’s serial number and model number when ordering parts or when seeking technical assistance. 1 B004C 1 Nameplate Figure 1 Replacement Parts If literature or replacement parts are required, contact the source from which the machine was purchased or contact Alliance Laundry Systems at (920) 748-3950 for the name and address of the nearest authorized parts distribut
Summary of the content on the page No. 10
Introduction Model Number Familiarization Guide Sample Model Number: *C125BYVQU60001 Model Number Prefix *C Washer-Extractor Capacity (pounds dry weight of laundry) 125 Type of Electrical Control B Actuation (Y = Prep for Card Reader) Y Washer-Extractor Speed Capability (V = Variable-Speed) V Electrical Characteristics Q Design Series U6 Option Identification (varies from machine to machine) 001 * Denotes Brand *C125BYVQU6001 00000000000 200 – 240 7 3 50 - 60 3 3 125 18 470 N/A N/A 0 500000 EXA
Summary of the content on the page No. 11
Operation Control Panel Figure 3 shows the control panel. 16 1 2 5 15 NORMAL PERM PRESS 6 WASH HOT WARM 14 ADD NORMAL PERM PRESS BLEACH 13 7 RINSE WARM COLD SPIN QUICK WH AS QUICK WASH 12 START DOOR 8 HOT WARM 11 HEAVY SOIL DELICATE HOT COLD 10 CHM482R 9 3 4 CHM482R 1 Cycle 1 9 START Keypad 2 Cycle 2 10 “Clean Filter” Indicator LED 3 Cycle 3 11 Door Open LED 4 Cycle 4/Up Edit 12 Spin Cycle LED 5 Cycle 5 13 Rinse Cycle LED 6 Cycle 6 14 Add Bleach LED 7 Cycle 7 15 Wash Cycle LED 8 Cycle 8/Down Edi
Summary of the content on the page No. 12
Operation Display Indicators Table 1 lists the various displays and what they mean. The operator should become familiar with these machine displays. Display Meaning Diagnostic test cycle selected or enabled tESt Spin (extract) step SPIn Supply signal 1 (“S1” output), normally detergent SUP1 Supply signal 2 (“S2” output), normally bleach SUP2 Supply signal 3 (“S3” output), normally softener SUP3 Supply signal 4 (“S4” output) SUP4 Supply signal 5 (“S5” output) SUP5 Spin coast (motor coasts after
Summary of the content on the page No. 13
Operation Table 1 (Continued) Display Meaning The first 3 digits are reserved for temperature reading, F indicates “degrees Fahrenheit” ___F “Fill error” – machine did not fill to programmed water level within 10 minutes FILL “Door” opened during cycle dOOr Machine user must “shut door” of the washer to allow the cycle to begin SHUt/door Control cannot unlock the door CAnt/OPEn Control will interpret the coin 2 input as a START signal from a Card Reader with no timing CArd max restriction, mea
Summary of the content on the page No. 14
Operation 5. Close door and turn handle clockwise to Operating Instructions horizontal position. Refer to Figure 6. 1. Turn on main power at its source (circuit breaker). 2. Use left hand to press and hold door unlock button located on top left of door lock box. Refer to Figure 4. 3. Turn handle counterclockwise to open. Refer to Figure 4. CHM2014N Figure 6 6. The default wash cycle will display. Refer to Figure 7. NOTE: Perm Press Cold is the default cycle if none is selected. WARNING
Summary of the content on the page No. 15
Operation 8. Add liquid and/or powder supplies to supply dispenser. 9. Insert and remove card. Contact the third party Card Reader manufacturer for details. CHM2015N Figure 8 10. When applicable, add bleach when the ADD BLEACH LED is lit. 11. Press the desired wash cycle keypad. Refer to Figure 7. 12. Press the START keypad. 13. During first fill, the desired wash cycle can be changed. After first fill has ended, the wash cycle active at that moment remains the chosen wash cycle. 14. W
Summary of the content on the page No. 16
Maintenance 3. Check door interlock before starting operation: WARNING a. Attempt to start the machine with the door open. The machine should not start with the Sharp edges can cause personal injury. door open. Wear safety glasses and gloves, use proper tools and provide lighting when b. Close the door without locking it and attempt handling sheet metal parts. to start the machine. The machine should not W366R1 start with the door unlocked. c. Close and lock the door, and start a cycle.
Summary of the content on the page No. 17
Maintenance Weekly Monthly 1. Clean the AC drive box filter(s) weekly or more NOTE: Disconnect power to the machine at its frequently as needed: source before performing the monthly maintenance procedures. NOTE: If fan filter service indicator light is on, fan filter must be cleaned immediately to prevent 1. Use the following procedures to determine if possible damage. Press the thermostat button to V-belt(s) require replacement or adjustment. Call reset the indicator light. a qualified
Summary of the content on the page No. 18
Maintenance c. Verify that V-belts are properly tensioned by applying a set force to the belt and measuring the deflection to determine the belt tension. Refer to Table 2 for the acceptable belt tension ranges. Belt tension measurements should be taken as close to the center of the belt span as possible. Refer to Figure 10. 1 2 H039I 1 Deflection 2 Span Length Figure 10 Belt Tension Testing Force Model Belt Belt Span Deflection Range Min – Max 125 Motor-Basket 50 in. (1270 mm) .78 in. (2
Summary of the content on the page No. 19
Maintenance 1 2 H047I H047I 1 Bearing Grease Fitting 2 Seal Grease Fitting Figure 11 3. Lubricate bearings and seals each month OR b. Pump the grease gun slowly, permitting only after every 200 hours of operation. Refer to the following number of strokes: Figure 11. ● Bearing grease fitting, 2 strokes a. Use a premium-grade lithium-based #2 ● Seal grease fitting, 1 stroke grease. Never mix two types of grease, such as petroleum and silicone. IMPORTANT: Do not pump the grease gun until greas
Summary of the content on the page No. 20
Maintenance 4. Remove back panel and check overflow hose and 5. Clean supplied steam filter, where applicable. drain hose for leaks. Refer to Figure 12. 5. Unlock the hinged lid and check the supply a. Turn off steam supply and allow time for the dispenser hoses and hose connections. valve to cool. 6. Clean inlet hose filter screens: b. Unscrew Cap. a. Turn water off and allow valve to cool, if c. Remove Element and clean. necessary. d. Replace Element and Cap. b. Unscrew inlet hose and rem
