Summary of the content on the page No. 1
User's Manual
SRP-770II
Label Printer
Rev. 1.14
http://www.bixolon.com
Summary of the content on the page No. 2
SRP-770II ■ Table of Contents ※ Manual Information & Usage Precautions ··································································3 1. Content Confirmation····································································································7 2. Product Part Names·······································································································8 3. Installation & Usage·········································································
Summary of the content on the page No. 3
SRP-770II ■ Manual Information ※ Manual Information & Usage Precautions This user manual contains basic information for product usage as well as for emergency measures that may be required. ※ The following separate manuals provide more detailed content on various technological issues and areas. 1. Windows Driver Manual This manual provides information on the installation instructions and main functions of the Windows Driver. 2. Unified Label Printer Utility Manual This manual pr
Summary of the content on the page No. 4
SRP-770II ■ Safety Precautions In using the present appliance, please keep the following safety regulations in order to prevent any hazard or material damage. WARNING Violating following instructions can cause serious injury or death. Do not plug several products in one multi-outlet. You must use only the supplied adapter. • This can provoke over-heating and a fire. • It is dangerous to use other adapters. • If the plug is wet or dirty, dry or wipe it before usage. • If the
Summary of the content on the page No. 5
SRP-770II CAUTION Violating following instructions can cause slight wound or damage the appliance. If you observe a strange smoke, odor or noise from Keep the desiccant out of children’s reach. the printer, unplug it before taking following • If not, they may eat it. measures. • Switch off the printer and unplug the set from the mains. • After the disappearance of the smoke, call your dealer to repair it. TO UNPLUG PROHIBIT PRINTER
Summary of the content on the page No. 6
SRP-770II ■ Other Precautions The copyright for this user manual and various other manuals is property of the BIXOLON Co., Ltd. Any copying or conversion into electronic firm and saving of this material without the express written permission of BIXOLON Co., Ltd. is strictly prohibited. Use of the information contained in this manual is not subject to any patent liability. This manual has been prepared with utmost care and attention to detail but may contain certain errors and/or om
Summary of the content on the page No. 7
SRP-770II 1. Content Confirmation The following items should all be contained in the printer package. Contact the dealer from which the purchase was made if any item is damaged and/or missing. SRP-770II Paper Power Cord AC Adapter Cleaning Pen CD User’s Manual ※ Optional items RS-232C(Serial) Cable IEEE1284 (Parallel) Cable USB Cable - 7 - Rev. 1.14
Summary of the content on the page No. 8
SRP-770II 2. Product Part Names Feed Button Power Switch Cover Peel-off Cover Lever Printer Head Paper Cover Paper Holder Paper Gap Sensor Paper Guide Peel-off Sensor - 8 - Rev. 1.14
Summary of the content on the page No. 9
SRP-770II Fan-Fold RS-232C Receptacle Dip Switch Power Receptacle IEEE1284 Receptacle USB Receptacle Auto Cutter (Option) - 9 - Rev. 1.14 LABEL PRNTER SAMSUNG
Summary of the content on the page No. 10
SRP-770II 3. Installation & Usage 3-1 Power Connection Connect power to the printer as shown below. OFF Power Switch AC Adapter Power Cord 1) Turn off the printer power switch. 2) Check to see that the AC adapter voltage matches that of the power source. 3) Connect the AC adapter jack to the printer power connector. 4) Connect the power cord to the AC adapter. 5) Connect the power cord to a power source/outlet. - 10 - Rev. 1.14
Summary of the content on the page No. 11
SRP-770II 3-2 Interface Cable Connection Connect the interface cable as shown below. This printer supports the following communications interface standards. - RS-232C (Serial) - IEEE1284 (Parallel) - USB USB Cable RS-232 (Serial) Cable IEEE1284 (Parallel) Cable 1) Turn off the power switch. 2) Connect the interface cable to the printer interface connector. - For a Serial cable, secure by tightening the screws on both sides. - For a Parallel cable, secure b
Summary of the content on the page No. 12
SRP-770II 3-3 Paper Installation 1) Open the Paper Cover. 2) Spread the paper holder and insert paper as shown. 3) Keep note of paper printing direction. 4) Adjust the paper guide to the width of the paper. 5) Close the Paper Cover. - 12 - Rev. 1.14 SAMSUNG LABEL PRINTER SAMSUNGLABEL PRINTER
Summary of the content on the page No. 13
SRP-770II 3-4 LED Display Feed button Paper feed or cancel the print job. LED The current printer status can be viewed. (Refer to below) The current printer status can be viewed via the printer’s LED display. 1) Green LED on - The printer waits for the data from Host (PC) in normal mode. 2) Orange LED on - It means paper gap sensing error. It becomes on when the printer fails to detect the paper or paper jam occurred. When fails to detect the paper correctly
Summary of the content on the page No. 14
SRP-770II 4. Self-Test The self-test checks whether the printer has any problems. (Users cannot perform this procedure if using the printer’s label peel-off option.) If the printer does not function properly, contact an authorized dealer. The self-test checks the following; 1) Make sure that the paper roll has been installed properly. 2) Turn on the power while holding down the FEED button. The self-test begins. 3) The self-test prints the current printer status, which pr
Summary of the content on the page No. 15
SRP-770II 5. Fine Tuning 5-1 Printer Settings with Dip switches The dip switches are located on the bottom of the printer. The dip switches are used to set the printer to perform various functions. Follow these steps when changing dip switch settings: 1) Turn the printer power switch off. 2) Remove the screw on the bottom of the printer and open the bracket. 3) Flip the dip switches using tweezers or another narrow-ended tool. Switches are off when up and on
Summary of the content on the page No. 16
SRP-770II [Table 1] Dip Switch 1 No Functions Details Off 4.0 ips 1-1 Speed Selection On 5.0 ips 4 3 2 Density Off Off Off 13 Off Off On 14 1-2 Off On Off 15 1-3 Density Selection Off On On 16 On Off Off 17 1-4 On Off On 18 On On Off 19 On On On 20 Off Normal Mode 1-5 Exhibition Selection On Demo Mode Off Label Paper 1-6 Media Selection On Thermal Continuous Paper Off Without Auto Cuter 1-7 Auto Cutter On With Auto Cuter Off Back Feeding Enable 1-8 Back Feed Opti
Summary of the content on the page No. 17
SRP-770II 5-3 Gap Sensor Auto-Calibration Gap sensor auto-calibration is used when the printer does not detect a gap on the label paper correctly. Generally a printer is set to detect most of gap types but sometimes it fails to detect and keep feeding the paper without a stop when special paper used. In such case, use gap sensor auto-calibration function for a proper detection. 1) Make sure that paper roll has been installed properly. 2) Turn on the power while holding down FE
Summary of the content on the page No. 18
SRP-770II 5-4 Gap Sensor Manual-Calibration Manual-calibration of media detection can be used when the printer cannot detect a media gap (or black mark) even after auto-calibration has been executed. Users can calibrate sensor parameters in detail by using the utility program provided by the manufacturer. The utility can be obtained from the enclosed CD or downloaded from the Internet via the BIXOLON website www.bixolon.com Please make sure the printer is connected and exec
Summary of the content on the page No. 19
PEELER OFF ON SRP-770II 5-5 The Peel-Off This function is used to automatically separate labels from the liner. - The peeler is for Label Paper only. - When the peeler switch is on, labels are not printed if previous printed labels have been removed from the peeler. - When the peeler function is not required, turn the peeler switch off. Keeping the switch on may result in the printer not working correctly. - When the peeler switch has been changed, the printer should be turned off
Summary of the content on the page No. 20
SRP-770II 3) Adjust the paper guides and close the cover. 4) Turn the printer off and back on. - 20 - Rev. 1.14
