Summary of the content on the page No. 1
™
Installation Guide
BI2015 — Ice Maker
www.U-LineService.com
Phone (414) 354-0300 • FAX (414) 354-7905
Service & Parts Tech Lines Phone (800) 779-2547 FAX (414) 354-5696
OnlineService@U-Line.com
©2005 U-Line Corporation
02/2005
Summary of the content on the page No. 2
™ BI2015 — Ice Maker Contents 1 Follow Safety Precautions Exterior Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Cut-Out Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 IMPORTANT Product Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 PLEASE READ all instructions completely before Door Swing/Clearances Information . . . . . . . . . . . . . . 5 attempting to install or operate the unit. Reversing the Door. . . . . . . . . . . .
Summary of the content on the page No. 3
™ BI2015 — Ice Maker General Precautions 2 Inspect and Plan Use this appliance for its intended purpose only and follow these general precautions along with those listed You have received a carton containing your BI2015 Ice throughout this guide: Maker with a package inside containing a User Manual, a Product Registration Card and water connection parts. WARNING Complete and mail the Product Registration Card or register online at www.U-LineService.com. Once your unit SHOCK HAZARD — Elect
Summary of the content on the page No. 4
™ BI2015 — Ice Maker After all the protective coating has been removed from 3 Prepare Site the unit/door, clean all Stainless Steel surfaces with Claire Stainless Steel Polish and Cleaner or comparable product or a mild detergent and warm water solution and soft Your U-Line product has been designed for either free- cloth. Do NOT use abrasive cleaning agents. standing or built-in installation. When built-in, your unit does not require additional air space for top, sides or rear. Note: If cl
Summary of the content on the page No. 5
™ BI2015 — Ice Maker Product Dimensions Reversing the Door (Black and White Units Only) 23-11/16" 25-13/16" Including Including All U-Line units (except Handle Handle Stainless Steel models) may be left- or right-hand opening. The door opening is easily reversed by moving the hinge hardware to the opposite side. The top hinge hardware will be used on the bottom of the other side and 34-1/8" 34-1/8" the bottom hinge hardware will be used on the top of the other side (see Figure 4). To
Summary of the content on the page No. 6
™ BI2015 — Ice Maker 4. Remove the two door closer inserts from the existing Other Site Requirements bottom hinge and install as shown on the new bottom hinge (see Figure 8). Power Supply The unit requires a grounded and polarized 115 VAC, 60 Hz, 15A circuit (normal household current). See Electrical Specifications on Page 14. Hinge Screw Pin Water Supply Door The unit requires a 1/4-inch OD water supply line and a Closer Inserts shut-off valve. For more information see Page 13. Environment
Summary of the content on the page No. 7
™ BI2015 — Ice Maker Side-By-Side Installation 4 Prepare and Install Door Panel Instructions (Black and White Units Only) For a complete refreshment center, install your BI2015 Ice Maker beside a U-Line Refrigerator, Combo, or Wine Two types of custom door panels can be installed on your Captain Model (see Figure 11 for typical cut-out). Note Black or White unit to harmonize with or accent the that each Side-By-Side Installation will be different. surrounding décor: a Custom 1/4" Insert or
Summary of the content on the page No. 8
™ BI2015 — Ice Maker Full Overlay Door Panel Door Panel Preparation A full overlay door panel completely covers the doorframe and handle to give a built-in appearance. See your U-Line dealer for the optional Full Overlay Door Panel Kit (P/N U-OL2015B — Black or P/N U-OL2015W — White). Appropriate hardware, Modified Handle, Replacement Hinges and a copy of these instructions will be included in the kit. 1. Cut the overlay to the following dimensions (see Figure 15). Figure 12 Figure 13 Ful
Summary of the content on the page No. 9
™ BI2015 — Ice Maker 4. Drill hole for upper door hinge (top of panel) (see 13/32" 0.177" Dia. (#16 Drill) Figure 16, Top View). 13/32" x 11/16" Deep 0.177" diameter 3/8" (#16 drill) x 11/16" deep 3/8" 5. Drill hole for lower door hinge (see Figure 16, Bottom Door Bottom: 13/16" 5/16" Dia. x 1/4" Deep View). Chamfer 1/32" x 45° Top View Bottom View 5/16" diameter x 1/4" deep CAUTION It is important to ensure that all drilled holes are drilled to 1/8" 1/8" 13/32" 1/8" the correct depth in ord
Summary of the content on the page No. 10
™ BI2015 — Ice Maker 4. Remove the top handle and discard. (This handle will be 2. Place and tape the existing door panel on the back of replaced with the Modified Handle included in the Full the overlay panel (see Figure 20) and drill holes Overlay Door Panel Kit.) through both panels according to Figure 21. Remove tape adjoining the panels and enlarge the six holes in 5. Remove the two screws located on both sides of the the overlay panel using a 0.201" (#7) drill. lower handle. Remove th
Summary of the content on the page No. 11
™ BI2015 — Ice Maker Typical Door Panel Pivot Post Wood Panel Wood Panel Top Hinge Plate Top (5/8" Longer than Existing Top Hinge Plate) Pivot Plate x #10 5/8" #8-32 x 1/2" Round Head Screw Flat Head Screw Six Required Three Places Plastic Spacer Top Pivot Plate Six Required Figure 22 Door Panel 5. Remove the existing bottom pivot plate and replace Figure 24 with the Full Overlay pivot plate (see Figure 23). 3. Install the pivot post into the new Replacement Bottom Hinge (using the 7/64" hex
Summary of the content on the page No. 12
™ BI2015 — Ice Maker 5 Adjust Door Checking Door Alignment The unit’s door is aligned at the factory before shipment. Slotted However, its alignment could have been disturbed during Mounting Notch Holes shipment or during door panel installation. IMPORTANT Properly aligned, the door should be 1/8" below the top of the unit’s cabinet, NOT flush with the top (see Figure 26). Raise Lower Outside Outside Door Edge Door Edge Figure 28 1/8" 3. See Figure 28. If the top far edge of the door needs to
Summary of the content on the page No. 13
™ BI2015 — Ice Maker 2. Locate the compression fitting and ferrule packed with 6Prepare Plumbing the unit. Slide the compression fitting and ferrule over the 1/4-inch OD water supply line. Do not use thread sealing compound or tape. Using two wrenches, CAUTION tighten the compression fitting on the supply line (see Figure 31). Plumbing installation must observe all state and local codes. All water connections MUST BE made by a licensed/ 3. Carefully bend the water qualified plumbing contr
Summary of the content on the page No. 14
™ BI2015 — Ice Maker 7 Prepare Power Supply 8 Level the Unit Electrical Specifications Leveling Information CAUTION IMPORTANT It is extremely important that the unit is level. If it is not Electrical installation must observe all state and local level, the ice mold will not fill evenly. codes. This unit requires connection to a grounded (three- prong), polarized receptacle that has been placed by a 1. Use a level to check the qualified electrician. levelness of the ice maker from front to b
Summary of the content on the page No. 15
OFF ON OFF ON ™ BI2015 — Ice Maker 9 Install the Unit 10 Start-Up for the First Time Installation of the BI2015 Initial Start-Up 1. Open the water supply valve in the main water source. Once installation and leveling is complete, the unit is ready for initial start-up and operation. The ON/OFF 2. Make sure the ON/OFF switch is in the OFF position (see switch is located in the front grille (see Figure 36). Figure 36). 3. Plug in the power cord. 4. Gently push the unit into position. Be carefu
Summary of the content on the page No. 16
™ BI2015 — Ice Maker Start-Up Troubleshooting Problem Q: Unit does not appear to turn on when switch is set to ON. Solution A: Make sure unit is plugged in and outlet has power (circuit breaker has not tripped). Remember that the ice maker mechanism will not fill the mold with water until the mold reaches the proper temperature. Problem Q: Water does not appear to be flowing into unit. Solution A: Check that the water is connected and turned on and the line is not obstructed. Problem Q: Ice
Summary of the content on the page No. 17
™ Who to Call Service Information If the need for service arises, contact the dealer from whom the unit was purchased. State the Model Number and Serial Number and explain the problem. The Model and Serial Number plate is located inside unit at upper right hand corner. If you need to locate a service company, you can go online at www.U-LineService.com and search for a service company by zip code. For more than four decades, U-Line has distinguished itself as the leader in built-in underco
