Summary of the content on the page No. 1
ULIN_016357_30098.fm Page 1 Tuesday, March 14, 2006 2:32 PM
Use and Care Guide
Ice Maker Models:
BI95, BI98, SP18
BI95
BI98 SP18
Summary of the content on the page No. 2
1 Introduction Congratulations on your purchase of a U-Line refrigeration product. A pioneer in the field for more than 40 years, U-Line Corporation is the world’s number one manufacturer of built-in, under-counter, specialty refrigeration and ice making products. U-Line dedicates 100% of its research and development to these products. The result: U-Line technology consistently leads the market with innovation, design, depth of product line and performance. U-Line products are making life mor
Summary of the content on the page No. 3
2 Table of Contents Introduction ...............................................................................................................................2 Warranty Registration .......................................................................................................2 Please Record Your Model Information ...........................................................................2 Table of Contents ...............................................................................
Summary of the content on the page No. 4
This page intentionally left blank 4 BI95, BI98, SP18
Summary of the content on the page No. 5
WARNING 3 Safety Precautions SHOCK HAZARD - Electrical Grounding Required. IMPOR IMPORT TAN ANT T � Never attempt to repair or perform maintenance on the unit until the electricity PLEASE READ all instructions completely before has been disconnected. attempting to install, operate, or service your unit. � Never remove the round grounding prong from • Proper installation procedures must be followed the plug and never use a two-prong grounding if this unit is being initially installed, or is
Summary of the content on the page No. 6
4 Product Features 5 Operation Origins Ice Maker 1 2 Models BI95, BI98, SP18 All Origins Ice Makers provide high daily ice production and storage capabilities, and conserve on water, using only 2-3/4 gallons (10.4 L) to produce approximately 22 lbs (10 kg) of ice. � Model 95 produces up to 23 lbs (10.4 kg) of ice per day and will store 12 lbs (5.4 kg). � Model 98 produces up to 25 lbs (11.3 kg) of ice per day and will store 25 lbs (11.3 kg). ULIN_0027_A � Model SP18 produces up to 20 lbs (
Summary of the content on the page No. 7
C O L Model SP18 Ice Maker To turn the unit on or off, press the rocker switch (Figure When the ice bucket is full, the ice making mechanism will 3) located in the center of the lower grille. shut off. However, the refrigeration system will continue to cool and maintain the cube supply. Ice Harvest Control IMPOR IMPORT TAN ANT T Adjustments are not normally needed. The control is preset at the factory. Do not place cans or bottles in the ice compartment because they will freeze. IMPOR IMPO
Summary of the content on the page No. 8
Normal Operating Sounds Storage, Vacation, Moving All models incorporate rigid foam insulated cabinets to If the unit will not be used for an extended period, or provide high thermal efficiency and maximum sound otherwise stored, follow these steps completely: reduction for its internal working components. In spite of this technology, your model may make sounds that are WARNING unfamiliar. Electrical Shock Hazard. Disconnect power before Normal operating sounds may be more noticeable ser
Summary of the content on the page No. 9
Product Disposal 6 Cleaning and Maintenance If the unit is being removed from service for disposal, check and obey all Federal, State and/or Local regulations General Cleaning regarding the disposal and recycling of refrigeration appliances, and follow these steps completely: Exterior Cleaning (As Required) 1. Disconnect power to the unit and unplug the power Black and White Models: cord from its outlet. � Surfaces may be cleaned with a mild detergent and warm water solution. Do not use sol
Summary of the content on the page No. 10
7. Dampen a soft sponge or non-abrasive cloth in clean Maintenance water and wipe down the cabinet interior and ice Proper maintenance of your U-Line product will ensure bucket to remove any detergent residue. Rinse the efficiency, top performance and long life. The sponge or cloth in clean water and repeat as necessary maintenance intervals listed are based on normal until the cabinet and ice bucket are clean. conditions. You may want to shorten the intervals if you have pets or other sp
Summary of the content on the page No. 11
6. DO NOT remove the inlet screen from the water 6. Insert the grille screw (Figure 8, 1) and tighten. Do not over-tighten. solenoid valve. Use a toothbrush to gently clean any sediment from the inlet screen. 7. Reconnect power to the unit. 7. Re-connect the water supply hose connector (Figure Ice Maker Maintenance 10, 1) to the water solenoid valve (Figure 10, 2). Tighten the connector securely. Inlet Screen 8. Open the water main supply valve and check for leaks Interval - Every Twelve
Summary of the content on the page No. 12
Ice Cube Thickness Adjustment Leveling Interval - As Required IMPOR IMPORT TAN ANT T The ice cube size may be adjusted by changing the amount of water injected into the ice maker assembly as It is extremely important that the unit sits on a follows: level surface, as it does not have feet levelers. If it is not level, the ice mold will not fill evenly. Use a level to check the levelness of the unit from front to back and from side to side. Level should be placed along top edge and side edg
Summary of the content on the page No. 13
Door Alignment Check and Adjustment IMPOR IMPORT TAN ANT T Properly aligned, the door’s gasket should be firmly in contact with the cabinet all the way around the door (no gaps). Carefully examine the door’s gasket to assure that it is firmly in contact with the cabinet. Also make sure the door gasket is not pinched on the hinge side of the door. ULIN_0293_A Figure 17 2. Remove top hinge from cabinet (three screws) (Figure 17). Hold door to keep it from falling. 3. Lift the door off the bo
Summary of the content on the page No. 14
5. Remove screws on opposite side of cabinet (Figure 19). 8. Remove plastic hole plug (Figure 22) from door handle Note that there may be a nut behind one or both and relocate on opposite side. screws on either side. 9. Remove pivot screw from top hinge, invert screw and reinstall pivot screw in top hinge. ULIN_0144_A ULIN_0123 _A Figure 23 Figure 20 10. Remove three plastic screw plugs (Figure 23) from hinge holes, top of cabinet, opposite side. Be careful 6. Install hinge on opposite sid
Summary of the content on the page No. 15
7 Service Before Calling for Service If your U-Line product appears to be malfunctioning, read through the OPERATION section of this guide to ensure that the function of all controls are clearly understood. If the malfunction persists, the TROUBLESHOOTING GUIDE in this guide will assist you in quickly identifying common problems, and provide information on possible causes and remedies. Most often, this will resolve the problem without the need to call for service. If Service is Required
Summary of the content on the page No. 16
Troubleshooting Guide DANGER ELECTROCUTION HAZARD Never attempt to repair or perform maintenance on the unit until the main electrical power has been disconnected. Troubleshooting - What to check when problems occur: PROBLEM POSSIBLE CAUSE REMEDY The unit frosts up. Unit is manual defrost model. Models SP18, 95, 98, CO29 and CO75 are manual defrost (See MAINTENANCE; DEFROSTING). Door gasket not sealing properly Adjust door (See MAINTENANCE; DOOR ALIGN, ADJUST, REVERSE). High ambient temperat
Summary of the content on the page No. 17
This page intentionally left blank BI95, BI98, SP18 17
Summary of the content on the page No. 18
This page intentionally left blank 18 BI95, BI98, SP18
Summary of the content on the page No. 19
U-Line Corporation Limited Warranty U-Line Corporation warrants each U-Line product to be free from defects in materials and workmanship for a period of one year from the date of purchase; and warrants the sealed system (consisting of the compressor, the condenser, the evaporator, the hot gas bypass valve, the dryer and the connecting tubing) in each U-Line product to be free from defects in materials and workmanship for a period of five years from the date of purchase. During the initial one
Summary of the content on the page No. 20
ULIN_016357_30098.fm Page 20 Tuesday, March 14, 2006 2:32 PM For General Inquiries: P.O. Box 245040 Milwaukee, Wisconsin 53224-9540 U.S.A. Phone (800) 779-2547 FAX (414) 354-5696 www.U-Line.com For Service and Parts Assistance: Phone (800) 779-2547 (414) 354-0300 FAX (414) 354-5696 Email: OnLineService@U-Line.com www.U-LineService.com E-mail: OnlineParts@u-line.com For more than four decades, U-Line has distinguished itself as the leader in built-in under-counter ice making, refrigera
