Summary of the content on the page No. 1
CLR60
P.O. Box 245040 CLEAR ICE
Milwaukee, WI 53224-9540
Phone 414.354.0300
MACHINE
FAX 414.354.7905
Printed in U.S.A.
R R
C
P/N 41952
R
User’s Manual
User’s Manual
Summary of the content on the page No. 2
U-LINE CORPORATION LIMITED WARRANTY U-Line Corporation warrants each U-Line product to be free from defects in materials and workmanship for a period of one year from the date of purchase; and warrants the sealed system (consisting of the compressor, the condenser, the evaporator, the hot gas bypass valve, the dryer and the connecting tubing) in each U-Line product to be free from defects in materials and workmanship for a period of five years from the date of purchase. During the initial one-y
Summary of the content on the page No. 3
INTRODUCTION Congratulations on your purchase of a U-Line CLR 60 Ice Maker. A pio- neer in the field for more than 35 years, U-Line is the world’s number one manufacturer of built-in, under-counter ice making and specialty refrigeration products. U-Line dedicates 100% of its research and development to these products. The result: U-Line leads the market with innovative technology and superior craftsmanship. U-Line also backs customers with a strong dealer network. U-Line’s commitment to qua
Summary of the content on the page No. 4
User’s Manual If you do not return your Warranty Registration Card, U-Line will use the date of sale to the U-Line distributor as the first date of warranty for your new ice maker. Please also record the purchase date or your U-Line unit and your dealer’s name, address and telephone number. Model Number: ________________________________________ Serial Number: ________________________________________ Purchase Date: ________________________________________ Dealer Name: __________________________
Summary of the content on the page No. 5
SAFETY PRECAUTIONS Do not attempt to install or operate your unit until you have read the safety precautions in this section. Safety items throughout this manu- al are labeled with Warning or Caution. WARNING ! ! Warning means that failure to follow this safety statement may result in extensive product damage, serious personal injury or death. CAUTION ! Caution means that failure to follow this safety state- ment may result in personal injury, property or equipment damage. WARNING ! ! • Never
Summary of the content on the page No. 6
User’s Manual CAUTION ! • Never install the unit behind closed doors. Be sure front grille is free of obstruction. Obstructing free air flow can cause the unit to malfunction, and may void the warran- ty. • Use only genuine U-Line replacement parts. Imitation parts can reduce ice rate, cause water to overflow from the ice maker, cause flooding, damage the unit and may void the warranty. WARNING ! ! DANGER: Risk of child entrapment. Before you throw away your old refrigerator or freezer: Take
Summary of the content on the page No. 7
DRAIN INSTALLATION PLEASE READ all instructions completely before attempting to install or operate the unit. All Ice Makers require a con- nection to the water supply and improper hook-up can result in substantial property damage! All water and drain connections MUST BE made by a licensed/qualified plumb- ing contractor. Failure to follow recommendations and instructions may result in damage and/or harm. CAUTION ! Plumbing installation must observe all state and local codes. All water and drain
Summary of the content on the page No. 8
User’s Manual WARNING ! ! To prevent accidental electrocution, make certain that the floor surfaces surrounding the unit are dry whenever power is removed from, or applied to the unit. 1. Make certain the unit is not plugged into an electrical outlet. 2. Using a screwdriver, carefully push the power cord grommet through the hole in the back panel. SCREWS BACK PANEL DRAIN FITTING POWER CORD GROMMET UL184-1 3. Using a screwdriver or 1/4" nut driver, remove 12 screws and back panel. 4. Check tha
Summary of the content on the page No. 9
5. Place a suitable container beneath the pump’s discharge tube. (The bucket must be able to hold a minimum of one gallon.) WARNING ! ! Back panel serves as a guard. DO NOT put your hands inside the ice maker cabinet or attempt to touch any com- ponents except the discharge tube during testing. Failure to follow this warning could result in serious personal injury or death. 6. Plug the ice maker power cord into a properly grounded, polarized electrical outlet. 7. Verify pump operation by pouring
Summary of the content on the page No. 10
User’s Manual • Overall maximum outside dimensions of 8-3/4" wide x 5-3/4" deep x 7-3/4" high. • Minimum flow rate of 15 gallons per hour at 10 feet of lift. • It must have a sealed sump which does not allow water leakage in the case of a power outage, restricted drain or pump failure. • It must have a check valve in the discharge line to prevent waste water return to the pump. • It must have an overflow protection control which will shut off power to the ice maker in the event of a pump failure
Summary of the content on the page No. 11
WARNING ! ! NEVER use an extension cord to connect power to the unit. Electrical Grounding Required. This appliance is equipped with a three prong (grounding) polarized plug for your protection against pos- sible shock hazards. WARNING ! ! Never remove the round grounding prong from the plug. Never use a two-prong grounding adapter. Where a two-prong wall receptacle is encoun- tered, contact a qualified electrician to have it replaced with a three-prong receptacle in accordance with applicable
Summary of the content on the page No. 12
User’s Manual • Install a shut-off valve in the 1/4 inch supply line. • Connect sufficient tubing to the unit to allow the unit to be moved for cleaning and ser- vicing. However, make cer- tain that the tubing is not pinched or damaged during installation. • U-Line specifies the use of copper tubing for installation. UL005A Position the unit to allow free air flow through the front grille Figure 3 (see Figure 3). 7. Wipe the inside and outside of the unit with a damp cloth. CONNECTING THE WATER
Summary of the content on the page No. 13
WATER LINE 4. Locate the compression fit- ting and ferrule packed in the unit. Slide the compression fitting and ferrule over the 1/4 inch water supply line. Do not use thread sealing compound or tape. Using two wrenches, tighten the compression fitting on the supply line (see Figure 6). UL204A Figure 8 6. For recessed installations, allow extra water supply line length to provide slack for easy removal from the recessed area (see Figure UL134 9). This will also safeguard Figure 6 against kin
Summary of the content on the page No. 14
User’s Manual NOTE After completing the installation, turn on the water and recheck water and drain connection for leaks. Apply addi- tional tightening if needed. Do NOT use thread sealing com- pound or tape. NOTE Route the water supply line through the clip on the sidewall of the unit in such a way as to prevent the line from com- ing in contact with any internal components other than the solenoid valve (see Figure 5). Normal operation creates some vibration. A water supply line contacting
Summary of the content on the page No. 15
TURN FOOT TO ADJUST UL205 UL215 Figure 11 Figure 10 3. Check the levelness after each adjustment and repeat the previous steps until the unit is level. GRILLE INSTALLATION 1. With a standard blade screwdriver (or 1/4" nutdriver), remove the screw needed to attach the grille (see Figure 12). 2. Carefully remove the grille, which is packaged inside of the unit. A small screw hole is located toward the top of the middle recessed section of the grille. GRILLE SCREW UL206 Figure 12 13
Summary of the content on the page No. 16
User’s Manual 3. Place the two hook-hinges (locat- ed on the rear bottom side of the grille) on the front lip of the unit base. Swing the grille up into posi- tion, aligning the grille and cabinet screw holes (see Figure 13). 4. Insert the screw, being careful not to over tighten. UL207 Figure 13 REVERSING THE DOOR Depending upon the location of the unit, it may be desirable to change the side on which the door is mounted. To reverse the door mounting, perform the following: 1. Remove grille (1
Summary of the content on the page No. 17
3. Lift the door off the bottom hinge. 4. Remove bottom hinge from cabinet (2 screws) (see Figure 16). Remove screws on opposite side of cabinet (see Figure 17). Note that there may be a nut behind one or both screws on either side. UL212 Figure 18 6. Relocate plastic spacer/ bushing on bottom of door to opposite side, and place door on bottom hinge pin (see Figure 19). Clean out bushing hole in door bottom with a screwdriver if needed. UL211 Figure 16 7. Remove plastic hole plug from door ha
Summary of the content on the page No. 18
User’s Manual HINGE RIGHT SIDE LEFT SIDE DOOR SWING DOOR SWING SCREW RIGHT SIDE INVERT INVERT HINGE SCREW HINGE UL115 Figure 20 8. Remove pivot screw from 11. Fasten upper hinge to unit top hinge, invert screw and (3 screws). Partially tighten reinstall pivot screw in top screws until door is aligned hinge (see Figure 20). (see Figure 22). 9. Remove three plastic plugs 12. Adjust door to assure proper in hinge holes, top of cabinet, seal. Tighten upper hinge opposite side. Be careful not scr
Summary of the content on the page No. 19
13. Replace three plastic plugs removed in step 8 into holes on top of unit. Replace screws in holes in bottom of unit, opposite side. 14. Reinspect door seal and alignment. Adjust if needed. 15. Reinstall grille (1 screw). ALIGNING THE DOOR For proper door alignment: 1. Loosen top and bottom hinge screws (see Figure 15). 2. Align door squarely with cabinet. 3. Assure gasket is firmly in contact with cabinet all the way around the door (no gaps). 4. Tighten bottom hinge screws. 5. Tighten top
Summary of the content on the page No. 20
User’s Manual B Custom Door Panel Dimensions Model A B CLR 60 28-5/32" 13-15/16" CLR 60SS 29-13/32" 13-15/16" A SS - Stainless steel units Install the insert as follows: WARNING ! ! Insert edges may be SHARP! Use care when installing. 1. Remove top hinge screw pin (large Phillips head, see Figure 23). Hold door to keep it from falling. 2. Remove door, being careful not to scratch top of door on hinge. 3. Remove two small screws holding door handle. Slightly UL131 separate door handle from
