Summary of the content on the page No. 1
PERLICK
SELF-CONTAINED ICE MAKER
MODELS:
H50IMS-R
H50IMS-L
H50IMW
H50IMS-ADL
H50IMS-ADR
H50IMW-AD
PRODUCT MANUAL
Issued: 11-2-2009
Summary of the content on the page No. 2
IMPORTANT This manual should be read carefully before the icemaker is installed and operated. Only qualified service technicians should install, service, and maintain the icemaker. Read the warnings contained in this booklet carefully as they give important information regarding safety. Please retain this booklet for any further reference that may be necessary. CONTENTS Important Safety Information ..............................................................................................
Summary of the content on the page No. 3
Important Safety Information Throughout this manual, notices appear to bring your attention to situations which could result in death, serious injury, or damage to the unit. WARNING Indicates a hazardous situation which could result in death or serious injury. CAUTION Indicates a situation which could result in damage to the unit. IMPORTANT Indicates important information about the use and care of the unit. WARNING This icemaker should be destined only to the use for which it has been e
Summary of the content on the page No. 4
I. Specifications A. Construction Top Panel Ice Making Mechanism Bin Control Thermostat Bulb Scoop Holder Slope Magnet Catch Front Panel Control Switch Door Power Cord Louver 4
Summary of the content on the page No. 5
B. Nameplate Rating PERLICK ICE MAKER MODEL NUMBER H50IMS-R SERIAL NUMBER AC SUPPLY VOLTAGE 115-120/60/1 AMPERES 3.4 AMPS DESIGN PRESSURE HI-240PSI LO-120PSI REFRIGERANT 134a 4.2 oz. MOTOR-COMPRESSOR THERMALLY PROTECTED APPROVED FOR OUTDOOR USE Perlick Corp. Milwaukee, WI 53223 www.bringperlickhome.com ICE MAKER 946Z Note: Only the "MODEL NUMBER" is replaced for other models. See the nameplate for electrical and refrigeration specifications. This nameplate is located inside the bin on the r
Summary of the content on the page No. 6
C. Dimensions/Connections 1. H50IMS-R, H-50IMS-L 6 Units: mm [in.]
Summary of the content on the page No. 7
2. H50IMW 7 Units: mm [in.]
Summary of the content on the page No. 8
3. H50IMS-ADL, H50IMS-ADR 8 Units: mm [in.]
Summary of the content on the page No. 9
4. H50IMW-AD 9 Units: mm [in.]
Summary of the content on the page No. 10
II. Installation and Operating Instructions WARNING 1. This icemaker must be installed in accordance with applicable national, state, and local regulations. 2. CHOKING HAZARD: Ensure all components, fasteners, and thumbscrews are securely in place after installation. Make sure that none have fallen into the storage bin. A. Checks Before Installation • Visually inspect the exterior of the shipping container and immediately report any damage to the carrier. Upon opening the container, any con
Summary of the content on the page No. 11
2. Built-In Installation Site CAUTION 1. Do not let the weight of the counter rest on the icemaker. 2. Do not install the icemaker in a corner where the door will interfere with other equipment or where the icemaker cannot be pulled out for service. Installation Space Model Height Width Depth H50IMS-R/L 34" (864 mm) minimum H50IMW 15" (381 mm) minimum 24" (610 mm) minimum H50IMS-ADR/ADL 32" (814 mm) minimum H50IMW-AD Between Two Cabinets Between a Cabinet and the End of a Counter H50IMS-R/L H5
Summary of the content on the page No. 12
C. Door Overlay Panel Fabrication and Attachment (H50IMW, H50IMW-AD) IMPORTANT The overlay panel must be crafted by a professional cabinet maker to ensure quality results. (1) Parts Ensure that all parts required for the overlay panel assembly are contained in the accessories bag. Overlay Panel Parts No. Description Part Number Qty. 1 Threaded Wood Insert 4A4004-01 6 2 T2 Screw 4×8 SS 7P32-0408 3 3 Pan Head Screw M4×25 SS 7C12-0425 4 4 Truss Head Screw M4×8 SS 7C32-0408 2 5 Canoe Clip 4A0629-0
Summary of the content on the page No. 13
(2) Overlay Panel Specification Use the specification that applies to your icemaker (H50IMW or H50IMW-AD) and the directions that follow to prepare your overlay panel. (a) H50IMW H50IMW Overlay Panel Specification Overlay Panel Height 29 17/32" (750 mm) Overlay Panel Width 14 13/16" (376 mm) Overlay Panel Thickness 5/8" (16 mm) minimum; 3/4" (19 mm) maximum Overlay Panel and Door Weight (total) 20 lb. (9 kg) maximum 13
Summary of the content on the page No. 14
(b) H50IMW-AD H50IMW-AD Overlay Panel Specification Overlay Panel Height 27 9/16" (700 mm) Overlay Panel Width 14 13/16" (376 mm) Overlay Panel Thickness 5/8" (16 mm) minimum; 3/4" (19 mm) maximum Overlay Panel and Door Weight (total) 20 lb. (9 kg) maximum 14
Summary of the content on the page No. 15
(3) Fabrication of Overlay Panel Fabricate the overlay panel as outlined in the applicable specification on the previous pages and the instructions below. 1) Rout a channel at the bottom of the overlay panel to the proper dimensions. See "(C) Routed Area" in the specification diagram and Fig. 1. 2) Drill six 1/4" diameter (hardwood may require slightly larger diameter) holes 3/8" (10 mm) deep in the locations designated. See "(A) Threaded Inserts" and "(B) Threaded Inserts" in the specifica
Summary of the content on the page No. 16
6) If you would like to reverse the door hinges, do the following: a) Remove "hinge (A)-left" from the accessory bag. b) Remove the 2 screws securing the top panel, then lift it off. See Fig. 4. c) Remove hinge (A)-right and the bracket from the right side of the unit. Set aside hinge (A)-right; it is not needed. Remove the top brace from the left side. Fasten hinge (A)-left and the bracket to the left side and the top brace to the right side. See Fig. 5. Note: When on the proper side, the
Summary of the content on the page No. 17
7) Remove the bushings from hinge (C1) and hinge (C2) (the hinges attached to the door). See Fig. 9. 8) Remove the gasket from the door. See Fig. 10. Bushing Gasket Hinge Fig. 10 Fig. 9 9) Temporarily fasten the overlay panel to the door using 2 of the M4×25 pan head screws provided. See Fig. 11. CAUTION Ensure that the back surface of overlay panel is flat before attaching. 10) Mark the centerpoint of the hinge (C1) and hinge (C2) holes that extend over the overlay panel. See Fig. 12. Hin
Summary of the content on the page No. 18
(4) Attachment of Overlay Panel to Door 1) Fasten the sheet metal bracket to the overlay panel using the two M4×8 truss head screws provided. Snug the screws, but do not tighten. See Fig. 13. 2) Temporarily fasten the overlay panel to the door using 2 of the M4×25 pan head screws provided. See Fig. 14. Overlay Panel Screws Snug the screws, but do not tighten. Sheet Metal Bracket Fig. 13 Fig. 14 3) Adjust the sheet metal bracket so that it is flush with the bottom of the door. See Fig. 15. 4
Summary of the content on the page No. 19
7) Tighten the four M4×25 pan head screws installed in step 5. See Fig. 19. 8) Replace the door gasket in its proper orientation. Reinsert the bushings into hinge (C1) and hinge (C2) (the hinges attached to the door). See Fig. 20. Bushing Tighten the screws. Gasket Bushing Fig. 19 Fig. 20 9) Attach the door to hinge (A), then continue to maintain a hold on the door. Screw the hinge stop pin into hinge (B) until it is tight. See Fig. 21. 10) Insert the 2 canoe clips included in the accessory ba
Summary of the content on the page No. 20
D. Setup 1) Position the icemaker in the selected permanent location. 2) Level the icemaker from side-to-side and front-to-rear by adjusting the feet. E. Electrical Connection WARNING 1. Electrical connection must meet national, state, and local electrical code requirements. Failure to meet these code requirements could result in death, electric shock, serious injury, fire, or severe damage to equipment. 2. This unit requires an independent power supply. See the nameplate for proper voltage
