Summary of the content on the page No. 1
NetLink e340/i640 Wireless Telephone
Mitel Networks 3300 and SX-200 ICP with 5220 IP Phone emulation
Setup and Administration
Part Number: 72-1084-02
Issue D
Summary of the content on the page No. 2
SpectraLink Corporation Setup and Administration—NetLink e340/i640 Wireless Telephone Mitel Networks 3300 and SX-200 ICP and 5220 IP Phone emulation NOTICE SpectraLink Corporation has prepared this document for use by SpectraLink personnel and clients. The drawings and specifications contained herein are the property of SpectraLink and shall be neither reproduced in whole or in part without the prior written approval of SpectraLink, nor be implied to grant any license to make, use, or sel
Summary of the content on the page No. 3
SpectraLink Corporation Setup and Administration—NetLink e340/i640 Wireless Telephone Mitel Networks 3300 and SX-200 ICP and 5220 IP Phone emulation Table of Contents 1. ABOUT THIS DOCUMENT 4 1.1 Contacting SpectraLink 4 1.2 Icons and Conventions 4 2. NETLINK E340/I640 WIRELESS TELEPHONE OVERVIEW 5 2.1 Quick Start Guide 6 2.2 System Diagram 7 2.3 System Components 8 3. THE NETLINK E340/I640 WIRELESS TELEPHONE 10 3.1 Specifications 10 3.2 The Display 11 3.3 Startup Sequence 12 3.4
Summary of the content on the page No. 4
SpectraLink Corporation Setup and Administration—NetLink e340/i640 Wireless Telephone Mitel Networks 3300 and SX-200 ICP and 5220 IP Phone emulation 1. About This Document This document explains how to configure and maintain the SpectraLink e340/i640 Wireless Telephone within the Mitel Networks 3300 and SX-200 Integrated Communications Platform (ICP). 1.1 Contacting SpectraLink SpectraLink wants you to have a successful installation. If you have questions please contact our Customer Sup
Summary of the content on the page No. 5
SpectraLink Corporation Setup and Administration—NetLink e340/i640 Wireless Telephone Mitel Networks 3300 and SX-200 ICP and 5220 IP Phone emulation 2. NetLink e340/i640 Wireless Telephone Overview The NetLink e340/i640 Wireless Telephone is a mobile handset for workplace IP telephone systems. NetLink Wireless Telephones operate over an 802.11b wireless Ethernet LAN providing users a wireless voice over IP (VoIP) extension. By seamlessly integrating with the Mitel IP telephony system, Ne
Summary of the content on the page No. 6
SpectraLink Corporation Setup and Administration—NetLink e340/i640 Wireless Telephone Mitel Networks 3300 and SX-200 ICP and 5220 IP Phone emulation 2.1 Quick Start Guide 1. A wireless LAN must be properly configured and operational through the use of 802.11b wireless access points (APs) listed on the NetLink Wireless Telephone Access Point Compatibility matrix. 2. A TFTP Server must be available on the network in order to load the appropriate software into the NetLink Wireless Telephon
Summary of the content on the page No. 7
SpectraLink Corporation Setup and Administration—NetLink e340/i640 Wireless Telephone Mitel Networks 3300 and SX-200 ICP and 5220 IP Phone emulation 2.2 System Diagram The following diagram shows the NetLink components residing on a network with the Mitel Networks IP telephony system, access points (APs), and wireless LAN Ethernet Switched Hub: Access Point TFTP Server NetLink SVP Server NetLink Ethernet switch Wireless Telephones Access Point Mitel ICP Platform optional Wirele
Summary of the content on the page No. 8
SpectraLink Corporation Setup and Administration—NetLink e340/i640 Wireless Telephone Mitel Networks 3300 and SX-200 ICP and 5220 IP Phone emulation 2.3 System Components • NetLink e340 Wireless Telephone – The NetLink e340 Wireless Telephone is a lightweight, durable handset specifically designed for mobile workplace use within a facility using the supported Mitel Networks IP telephony system and 802.11b APs in a wireless LAN. • NetLink i640 Wireless Telephone – The NetLink i640 Wirele
Summary of the content on the page No. 9
SpectraLink Corporation Setup and Administration—NetLink e340/i640 Wireless Telephone Mitel Networks 3300 and SX-200 ICP and 5220 IP Phone emulation Access points must utilize SpectraLink Voice Priority (SVP). Contact SpectraLink, or a certified SpectraLink distributor, for information about APs that support SVP. • Ethernet Switch – interconnects multiple network devices, including the NetLink SVP Server, the supported Mitel Networks IP telephony system, Mitel Networks IP Phones and the a
Summary of the content on the page No. 10
SpectraLink Corporation Setup and Administration—NetLink e340/i640 Wireless Telephone Mitel Networks 3300 and SX-200 ICP and 5220 IP Phone emulation 3. The NetLink e340/i640 Wireless Telephone NetLink e340 Wireless Telephone NetLink i640 Wireless Telephone 3.1 Specifications Radio frequency 2.4000 – 2.4835 GHz Transmission type Direct Sequence Spread Spectrum (DSSS) Transmit data rate up to 11 Mb/s Radio QoS SpectraLink Voice Priority (SVP) Wireless security Wired Equivalent Privac
Summary of the content on the page No. 11
SpectraLink Corporation Setup and Administration—NetLink e340/i640 Wireless Telephone Mitel Networks 3300 and SX-200 ICP and 5220 IP Phone emulation 3.2 The Display Alphanumeric Display information provided by the supported Mitel Networks VoIP solution when the Wireless Telephone is off-hook will be passed directly to the Wireless Telephone display. The Wireless Telephone will display up to 18 characters of each line. Certain characters may be used by the supported Mitel IP PBX solut
Summary of the content on the page No. 12
SpectraLink Corporation Setup and Administration—NetLink e340/i640 Wireless Telephone Mitel Networks 3300 and SX-200 ICP and 5220 IP Phone emulation 3.3 Startup Sequence The Wireless Telephone goes through an initialization sequence at startup that follows the following pattern: Icon The icon(s) shown in bold turns off when: 123456789 The Wireless Telephone has located and authenticated and associated with at least one AP, and is proceeding to bring up higher-layer networking functions.
Summary of the content on the page No. 13
SpectraLink Corporation Setup and Administration—NetLink e340/i640 Wireless Telephone Mitel Networks 3300 and SX-200 ICP and 5220 IP Phone emulation 3.4 Wireless Telephone Modes Standby In the standby mode the Wireless Telephone is waiting for an incoming (on-hook) call or for the user to place an outgoing call. The extension number is shown on the display and there is no dial tone. In this mode, the Wireless Telephone is conserving battery power and wireless LAN bandwidth. When an inc
Summary of the content on the page No. 14
SpectraLink Corporation Setup and Administration—NetLink e340/i640 Wireless Telephone Mitel Networks 3300 and SX-200 ICP and 5220 IP Phone emulation 3.5 Wireless Telephone Displays Status Displays information from the PBX in one line of text and displays display available softkeys on the second line. Muted is displayed when local muting is activated. The PBX text may be truncated as the 5220 IP phone has 20 characters and the Wireless Telephone display area is 18 characters. LINE disp
Summary of the content on the page No. 15
SpectraLink Corporation Setup and Administration—NetLink e340/i640 Wireless Telephone Mitel Networks 3300 and SX-200 ICP and 5220 IP Phone emulation 4. NetLink e340/i640 Wireless Telephone Configuration The NetLink e340/i640 Wireless Telephones should be provisioned in the supported Mitel Networks VoIP solution in the same manner as the Mitel Networks 5220 Internet Telephones. Each Wireless Telephone may be configured for site-specific requirements by opening the Admin menu and selecting
Summary of the content on the page No. 16
SpectraLink Corporation Setup and Administration—NetLink e340/i640 Wireless Telephone Mitel Networks 3300 and SX-200 ICP and 5220 IP Phone emulation Alphanumeric String Entry 1. Press the first digit/letter. The digit displays. Press the key again to scroll through the letters associated with that key. Example: if you press 2 repeatedly, you will see 2, A, B, and C, a, b, and c. The following table shows which key will allow you to enter non-numeric characters or other characters not rep
Summary of the content on the page No. 17
SpectraLink Corporation Setup and Administration—NetLink e340/i640 Wireless Telephone Mitel Networks 3300 and SX-200 ICP and 5220 IP Phone emulation The following table lists the Admin Menu items. Detailed descriptions of each item appear below the table. nd rd th Admin Menu Items 2 Level 3 Level 4 Level IP Address *Use DHCP Static IP Phone IP TFTP Server IP Default Gateway Subnet Mask SVP IP Addr RTC IP Addr OAI Server IP ESS ID Static Entry *Learn Once Learn Always
Summary of the content on the page No. 18
SpectraLink Corporation Setup and Administration—NetLink e340/i640 Wireless Telephone Mitel Networks 3300 and SX-200 ICP and 5220 IP Phone emulation IP Address There are two modes in which the Wireless Telephone can operate: DHCP enabled or Static IP. Select the mode for operation from the IP Address menu: * Use DHCP: will use Dynamic Host Configuration Protocol to assign an IP Address each time the Wireless Telephone is turned on. If DHCP is enabled, the Wireless Telephone also receives
Summary of the content on the page No. 19
SpectraLink Corporation Setup and Administration—NetLink e340/i640 Wireless Telephone Mitel Networks 3300 and SX-200 ICP and 5220 IP Phone emulation administrator for the proper settings for your network. Note that the Wireless Telephones cannot “roam” across subnets, since they cannot change their IP Address while operational. Ensure that all your access points are attached to the same subnet for proper operation. The Wireless Telephone can change subnets if DHCP is enabled, and the Wire
Summary of the content on the page No. 20
SpectraLink Corporation Setup and Administration—NetLink e340/i640 Wireless Telephone Mitel Networks 3300 and SX-200 ICP and 5220 IP Phone emulation powered off. See the Certifying the NetLink e340/i640 Wireless Telephone section for more information on this mode. Regulatory Domain The Regulatory Domain will default to North America on the Wireless Telephone display. FCC requirements dictate that the menu for changing the domain be available by password, which in our case is the LINE key
