Invacare JYMNI 9000 user manual

User manual for the device Invacare JYMNI 9000

Device: Invacare JYMNI 9000
Category: Mobility Aid
Manufacturer: Invacare
Size: 0.85 MB
Added : 10/21/2013
Number of pages: 24
Print the manual

Download

How to use this site?

Our goal is to provide you with a quick access to the content of the user manual for Invacare JYMNI 9000. Using the online preview, you can quickly view the contents and go to the page where you will find the solution to your problem with Invacare JYMNI 9000.

For your convenience

If looking through the Invacare JYMNI 9000 user manual directly on this website is not convenient for you, there are two possible solutions:

  • Full Screen Viewing - to easily view the user manual (without downloading it to your computer), you can use full-screen viewing mode. To start viewing the user manual Invacare JYMNI 9000 on full screen, use the button Fullscreen.
  • Downloading to your computer - You can also download the user manual Invacare JYMNI 9000 to your computer and keep it in your files. However, if you do not want to take up too much of your disk space, you can always download it in the future from ManualsBase.
Invacare JYMNI 9000 User manual - Online PDF
Advertisement
« Page 1 of 24 »
Advertisement
Print version

Many people prefer to read the documents not on the screen, but in the printed version. The option to print the manual has also been provided, and you can use it by clicking the link above - Print the manual. You do not have to print the entire manual Invacare JYMNI 9000 but the selected pages only. paper.

Summaries

Below you will find previews of the content of the user manuals presented on the following pages to Invacare JYMNI 9000. If you want to quickly view the content of pages found on the following pages of the manual, you can use them.

Abstracts of contents
Summary of the content on the page No. 1




 

 



Summary of the content on the page No. 2

WARNING WARNING DO NOT INSTALL THIS EQUIPMENT WITHOUT FIRST READING AND UNDERSTANDING THIS MANUAL AND THE 9000 W WHEELCHAIR OWNER'S MANUAL (PART NUMBER 1056953) A R AND SERVICE MANUAL (PART NUMBER 1076155) . IF YOU ARE N UNABLE TO UNDERSTAND THE WARNINGS, CAUTIONS, AND I N INSTRUCTIONS, CONTACT A HEALTHCARE PROFESSIONAL, G DEALER OR TECHNICAL PERSONNEL IF APPLICABLE BEFORE ATTEMPTING TO USE THIS EQUIPMENT - OTHERWISE INJURY OR DAMAGE MAY RESULT. THE PROCEDURES IN THIS MANUAL MUST BE PERFORMED BY

Summary of the content on the page No. 3

CONTENTS TABLE OF CONTENTS SAFETY SUMMARY ................................................................................................................................4 MAINTENANCE ....................................................................................................................................... 4 C PROCEDURE 1 - ASSEMBLY .................................................................................................................. 5 O ASSEMBLIES .......................

Summary of the content on the page No. 4

SAFETY SUMMARY/MAINTENANCE SAFETY SUMMARY S NOTE: Refer to the 9000 Wheelchair Owner's Manual, Part Number 1056953 and Service Manual, Part Number A 1076155 for additional safety information and overall maintenance requirements. F E STABILITY WARNINGS T CLD installation may require changes to the current configuration of the wheelchair with respect to Y rear wheel and caster size. The back height, front caster size and/or position, seat-to-floor angle, position and/or size of the rear wheels, c

Summary of the content on the page No. 5

ASSEMBLY PROCEDURE 1 Wheelchairs Built AFTER 09/05/00 This Procedure includes the following: 1. Transmission and Wheel Lock Assemblies 2. Drive Arm Assembly, Support Bracket and Steering Link Tools Needed 3. Upper Drive Arm NOTE: The procedures in this manual should be per- 4. Fork Assembly A 5. Rear Wheel Mounting Hardware formed on the specific side of the wheelchair the CLD S was ordered for. S TOOLS NEEDED E ASSEMBLIES (FIGURE 1) NOTE: Have the following tools available. M The Cyclical Lever

Summary of the content on the page No. 6

aa aa PROCEDURE 2 FORK ASSEMBLY Removing CLD Fork This Procedure includes the following: Installing CLD on Existing Wheelchair 1. Remove the caster journal cap. F Replacing CLD Fork Assembly 2. Remove the hex nut securing the fork to the caster O headtube. Removing Fork and Caster R 3. Drop the caster and fork out of the caster headtube. Mounting Caster to CLD Fork Assembly K 4. Remove the caster from the fork. Refer to REMOV- Installing CLD Fork Assembly onto Wheelchair ING CASTER in this proce

Summary of the content on the page No. 7

FORK ASSEMBLY PROCEDURE 2 1. Refer to the chart below to determine which mount- MOUNTING CASTER TO CLD FORK ing position should be used. ASSEMBLY (FIGURE 2) 2. Secure the caster to the CLD fork assembly in the F WARNING mounting position determined in STEP 1 with the hex O If not changing the wheelchair's current configu- head bolt, washers and the hex nut as shown in FIG- R ration (seat angle, caster size or seat-to-floor URE 2. Tighten securely. height), refer to the chart below to determine K

Summary of the content on the page No. 8

PROCEDURE 3 REAR WHEEL/TRANSMISSION 4. Install the NEW hub support plates. Refer to IN- This procedure includes the following: STALLING/REMOVING THE HUB SUPPORT Installing CLD on Existing Wheelchair PLATES in this procedure of the manual. Replacing the Hub Attachment REPLACING THE TRANSMISSION Replacing the Transmission R 1. Remove the EXISTING drive arm assembly from the Removing Existing Wheel Lock E transmission rear hub. Refer to INSTALLING/REMOV- A Removing the Existing Rear Wheel ING DRIVE

Summary of the content on the page No. 9

REAR WHEEL/TRANSMISSION PROCEDURE 3 Bolt and Locknut Wheelchair Wheelchair Frame Axle Mounting Positions Frame Axle Spacer (Conventional R Arms Only) E A Quick- Wheel R Release Axle Lock W Rear Wheel FIGURE 1 - REMOVING EXISTING WHEEL LOCK H E FIGURE 3 - REMOVING THE EXISTING REAR REMOVING THE EXISTING REAR E WHEEL - QUICK-RELEASE AXLES WHEEL L Permanent Axles (FIGURE 2) INSTALLING/REMOVING REAR WHEEL TO/FROM TRANSMISSION 1. Note the mounting position on the wheelchair frame for proper reinstall

Summary of the content on the page No. 10

PROCEDURE 3 REAR WHEEL/TRANSMISSION 4. Secure axle bolt to wheelchair side frame with hex INSTALLING/REMOVING THE AXLE nut. Tighten securely. BOLT (FIGURE 4) Removing Installing 1. Remove hex nut securing axle bolt to wheelchair side 1. If necessary, install rear wheel onto transmission rear R frame. hub. Refer to INSTALLING/REMOVING THE REAR E 2. Remove axle bolt from wheelchair side frame. WHEEL TO/FROM THE TRANSMISSION REAR A HUB in this procedure of the manual. 3. Remove inner hub spacer, ax

Summary of the content on the page No. 11

DRIVE ARM/SUPPORT BRACKET PROCEDURE 4 4. Install the NEW support bracket onto the wheelchair. This procedure includes the following: Refer to MOUNTING/REMOVING SUPPORT Installing CLD on Existing Wheelchair BRACKET TO WHEELCHAIR in this procedure of the manual. Replacing Support Bracket Replacing Drive Arm Assembly D REPLACING DRIVE ARM ASSEMBLY Mounting/Removing Support Bracket To/From R 1. Remove the EXISTING support bracket. Perform Wheelchair I STEPS 5-6 in REMOVING/INSTALLING SUPPORT Removi

Summary of the content on the page No. 12

PROCEDURE 4 DRIVE ARM/SUPPORT BRACKET Wheelchairs Built BEFORE 09/05/00 REMOVING/INSTALLING SUPPORT Drive Arm BRACKET TO/FROM DRIVE ARM Assembly ASSEMBLY (FIGURE 2) Wheelchair D Removing Flat Side Frame R Hex Washer 1. Remove the locknut securing the drive arm assembly Nut I bolt to the support bracket. V NOTE: DO NOT remove the drive arm assembly bolt, E spacer or washer from the drive arm assembly when removing it from the support bracket. Flat A Screw 2. Remove the drive arm assembly, includi

Summary of the content on the page No. 13

DRIVE ARM/SUPPORT BRACKET PROCEDURE 4 INSTALLING/REMOVING DRIVE INSTALLING/REMOVING DRIVE ARM ASSEMBLY TO/FROM ARM (FIGURE 4) TRANSMISSION (FIGURE 3) Installing D Installing WHEELCHAIRS BUILT BEFORE 09/05/00. R 1. Secure the drive arm assembly to the transmission 1. Loosen, but DO NOT remove the drive arm release I lever and wheel lock support bracket with hex screw, lever by rotating COUNTERCLOCKWISE. V two (2) fender washers, shifter spacer and hex nut. 2. Rotate the drive arm to align the fl

Summary of the content on the page No. 14

PROCEDURE 4 DRIVE ARM/SUPPORT BRACKET Wheelchairs Built BEFORE 09/05/00 ADJUSTING DRIVE ARM RELEASE LEVER/BRACKET RELEASE LEVER (FIGURE 4) D NOTE: Wheelchair built BEFORE 09/05/00 are equipped with a drive arm release lever AND a bracket release R Drive Arm elver, wheelchairs built AFTER 09/05/00 are equipped I with a bracket release lever ONLY. V E NOTE: The drive arm release lever/ bracket release le- Flat ver can be rotated to keep it from protruding from the Surface drive arm. A Plunger R 1.

Summary of the content on the page No. 15

DRIVE ARM/SUPPORT BRACKET PROCEDURE 4 Wheelchairs Built BEFORE 09/05/00 Wheelchairs Built AFTER 09/05/00 D Drive Arm Drive Arm R Button I Screw V Button Screw E Mounting Mounting Hole (NOT A Hole Shown) R M Plunger Plunger Tube Tube Mounting Hole S U P P O FIGURE 5- ADJUSTING DRIVE ARM HEIGHT R T B R A C K E T 15

Summary of the content on the page No. 16

PROCEDURE 5 WHEEL LOCK This procedure includes the following: ADJUSTING WHEEL LOCK ASSEMBLY POSITION (FIGURE 2) Installing CLD on Existing Wheelchair Replacing the CLD Wheel Lock NOTE: If wheels are pneumatic, before adjusting the W Installing/Removing CLD Wheel Lock wheel lock, ensure that the tires are inflated to the rec- H ommended psi located on the side wall of the tire. Adjusting Wheel Lock Assembly Position E Adjusting Wheel Lock Engagement Position 1. Refer to the chart on this page to

Summary of the content on the page No. 17

WHEEL LOCK PROCEDURE 5 Wheelchairs Built BEFORE 09/05/00 ADJUSTING WHEEL LOCK Wheel Lock Adjustment Rod ENGAGEMENT POSITION (FIGURE 3) Wheel Lock WARNING Support W The shift lever MUST be in the neutral position before Bracket H activating the wheel lock. Failure to do so can E cause accidental release and make it more diffi- cult to disengage the wheel lock feature. E Flat Screws L 1. Place the shift lever in the neutral (center) position. 2. Perform one (1) of the following (DETAIL "A"): L Whe

Summary of the content on the page No. 18

PROCEDURE 5 WHEEL LOCK Wheelchairs Built BEFORE 09/05/00 Wheelchairs Built AFTER 09/05/00 Wheel Lock Wheel Lock DETAIL "A" DETAIL "A" Adjustment Rod Adjustment Rod W Drive 1/4-INCH 1/4-INCH H Arm ENGAGEMENT ENGAGEMENT E Drive E Arm Outside Outside L Edge of Edge of Tire Tire L Wheel Wheel O Lock Lock C Block Block K Flat Flat Screws Screws Shift Lever Shift Lever Rear Tire Rear Tire Knob Knob FIGURE 3- ADJUSTING WHEEL LOCK ENGAGEMENT POSITION 18

Summary of the content on the page No. 19

STEERING LINK PROCEDURE 6 Removing This procedure includes the following: 1. Compress and hold straight section of the fork spring Installing CLD on Existing Wheelchair by pushing spring horizontally towards fork. S Replacing the Steering Link 2. Pull up on the steering pin to remove from the fork. T Connecting/Removing Steering Link To/From Fork E Adjusting Caster and Drive Arm Alignment E Removing/Installing Steering Link Steering Link R Hole I Steering Pin WARNING N (REMOVED) After ANY adjust

Summary of the content on the page No. 20

PROCEDURE 6 STEERING LINK 7. Repeat STEPS 1-6 until the caster points straight 3. Perform the following steps. Refer to CHART A for ahead. an example of thread calculation. 8. Balance the steering link. Refer to BALANCING THE A. Count the number of drive arm threads and steer- STEERING LINK in this procedure of the manual. S ing pin threads between the rod ends and the T steering link. Balancing the Steering Link E B. Divide the number of threads determined in NOTE: The steering link MUST be bal


Alternative user manuals
# User manual Category Download
1 Invacare 01-349 User manual Mobility Aid 4
2 Invacare 1000 User manual Mobility Aid 6
3 Invacare 1035965 User manual Mobility Aid 1
4 Invacare 1035966 User manual Mobility Aid 0
5 Invacare 1034177 User manual Mobility Aid 0
6 Invacare 1036901 User manual Mobility Aid 0
7 Invacare 1036793 User manual Mobility Aid 0
8 Invacare 1048085 User manual Mobility Aid 0
9 Invacare 1038599 User manual Mobility Aid 0
10 Invacare 1036794 User manual Mobility Aid 0
11 Invacare 1048919 User manual Mobility Aid 0
12 Invacare 1036900 User manual Mobility Aid 0
13 Invacare 1048920 User manual Mobility Aid 0
14 Invacare 1048086 User manual Mobility Aid 0
15 Invacare 1048922 User manual Mobility Aid 0
16 Adcom A720 User manual Mobility Aid 1
17 Alvin CH444 User manual Mobility Aid 0
18 Alvin DC445 User manual Mobility Aid 0
19 Alvin CH728 User manual Mobility Aid 0
20 Alvin Comfort Economy CH277 User manual Mobility Aid 0