Summary of the content on the page No. 1
INSTALLATION &
OPERATION MANUAL
VBP SERIES FOOD HOLDING AND
TRANSPORT CABINETS
MODELS
VBP4 ML-126352
VBP7 ML-126353
VBP13 ML-126355
VBP15 ML-126356
VBP40 ML-126357
VBP7I ML-126358
VBP13I ML-126359
VBP15I ML-126360
VBP77 ML-126354
VBP77I ML-126361
VBP8HI ML-126362
VBP12HI ML-126363
VBP15HI ML-126364
VBP7I
In U.S.A.: In Canada:
VULCAN-HART COMPANY HOBART FOOD EQUIPMENT GROUP CANADA
P.O. BOX 696 190 RAILSIDE ROAD
LOUISVILLE, KY NORTH YORK, ONTARIO
40201-0696 M3A 1B1
TEL.: 502-778-2791 TEL.: 1-800-4
Summary of the content on the page No. 2
TABLE OF CONTENTS GENERAL............................................................................................................................................. 3 INSTALLATION .................................................................................................................................... 4 Unpacking ................................................................................................................................. 4 Location ................................
Summary of the content on the page No. 3
Installation, Operation and Care of MODEL VBP SERIES FOOD HOLDING AND TRANSPORT CABINETS PLEASE KEEP THIS MANUAL FOR FUTURE USE GENERAL Vulcan-Hart Holding and Transport Cabinets are produced with quality workmanship and material. Proper installation, usage, and maintenance of your cabinet will result in many years of satisfactory performance. It is suggested that you thoroughly read this entire manual and carefully follow all of the instructions provided. The VBP series Holding and Transport Ca
Summary of the content on the page No. 4
INSTALLATION Before installing, verify that the electrical service agrees with the specifications on the rating plate located on the lower left corner. If the supply and equipment requirements do not agree, do not proceed with the installation. Contact your dealer or Hobart Food Equipment Group Canada immediately. UNPACKING This cabinet was inspected before leaving the factory. The transportation company assumes full responsibility for safe delivery upon acceptance of the shipment. Immediately a
Summary of the content on the page No. 5
INSTALLATION CODES AND STANDARDS The cabinet must be installed in accordance with: In the United States of America: 1. State and local codes. 2. National Electrical Code, ANSI/NFPA-70 (latest edition). Copies may be obtained from The National Fire Protection Association, Batterymarch Park, Quincy, MA 02269. In Canada: 1. Local codes. 2. Canadian Electrical Code, CSA C22.1 (latest edition). Copies may be obtained from The Canadian Standard Association, 178 Rexdale Blvd., Etobicoke, Ontario, Canad
Summary of the content on the page No. 6
Electrical Table Model Voltage Amp Phase Hz NEMA Plug 110/120 10 5-15 VBP4 160 208/240 5.4 6-15 110/120 10 5-15 VBP7 160 208/240 5.4 6-15 110/120 10 5-15 VBP13 160 208/240 5.4 6-15 110/120 10 5-15 VBP15 160 208/240 5.4 6-15 110/120 16.7 5-20 VBP40 160 208/240 9 6-15 110/120 10 5-15 VBP7I 160 208/240 5.4 6-15 110/120 10 5-15 VBP13I 160 208/240 5.4 6-15 110/120 10 5-15 VBP15I 160 208/240 5.4 6-15 110/120 20 5-30 VBP77 160 208/240 10.9 6-15 110/120 20 5-30 VBP77I 160 208/240 10.9 6-15 110/120 16.7
Summary of the content on the page No. 7
WIRING DIAGRAMS – 7 – VBP4, VBP7, VBP13, VBP15, VBP40, VBP7I, VBP13I, VBP15I
Summary of the content on the page No. 8
– 8 – VBP77, VBP77I
Summary of the content on the page No. 9
– 9 – VBP8HI, VBP12HI, VBP15HI
Summary of the content on the page No. 10
OPERATION WARNING: THE CABINET AND ITS PARTS ARE HOT. BE VERY CAREFUL WHEN OPERATING, CLEANING OR SERVICING THE CABINET. CONTROLS THERMOMETER HEAT INDICATOR LIGHT FULL RANGE THERMOSTAT POWER INDICATOR LIGHT PL-41226-1 Fig. 1 All Models (Fig.1) POWER INDICATOR LIGHT – Lit when power is supplied to cabinet. HEAT INDICATOR LIGHT – Lit when heat is supplied to cabinet. FULL RANGE THERMOSTAT – Turn to desired temperature setting. THERMOMETER – Indicates interior temperature of cabinet. Models VBP8HI
Summary of the content on the page No. 11
OPERATING CABINET 1. Connect electric power supply. • Power indicator light is lit. 2. If cabinet is a VBP8HI, VBP12HI, or VBP15HI, press ON/OFF switch ON. • Interior air circulating fans start. • Control/component compartment cooling fans start. 3. Turn thermostat knob to desired setting. • Heating elements begin heating. • Heat indicator light is lit. 4. Thermometer will indicate the interior temperature of the cabinet. 5. Once desired temperature is reached, heating elements will cycle on and
Summary of the content on the page No. 12
Shutdown If cabinet is a VBP8HI, VBP12HI, or VBP15HI, press ON/OFF switch OFF. Extended Shutdown Unplug electrical power supply. Power indicator light will go off. CLEANING WARNING: UNPLUG ELECTRICAL POWER SUPPLY BEFORE CLEANING. Clean cabinet interior with a mild soap and water whenever food spill occurs. Never use harsh chemicals or abrasive pads to clean cabinet. Daily 1. Allow cabinet to cool before cleaning. 2. Remove the tray slides and clean in a sink as you would any normal utensil. 3.
