Summary of the content on the page No. 1
ML-1
TECHNICAL EDUCATION
Epic™
FRONT-LOADING
AUTOMATIC WASHER
MODEL MFW 9700S
MFW 9600S
JOB AID 8178604
Summary of the content on the page No. 2
FORWARD This Maytag Job Aid Epic Front-Loading Automatic Washer” (Part No. 8178604), provides the In Home Service Professional with information on the installation, operation, and service of the Front- Loading Automatic Washer. It is to be used as a training Job Aid and Service Manual. For specific information on the model being serviced, refer to the “Use and Care Guide,” or “Tech Sheet” provided with the washer. The Wiring Diagram used in this Job Aid is typical and should be used for traini
Summary of the content on the page No. 3
TABLE OF CONTENTS Page GENERAL.............................................................................................................................. 1-1 Safety First ........................................................................................................................ 1-1 Model & Serial Number Designations ............................................................................... 1-2 Model & Serial Number Label And Tech Sheet Locations .............................
Summary of the content on the page No. 4
Page COMPONENT TESTING ....................................................................................................... 5-1 Pressure Switch ................................................................................................................ 5-1 Detergent Dispenser Motor & Switch ................................................................................ 5-2 Inlet Valve Solenoids ..............................................................................................
Summary of the content on the page No. 5
GENERAL SAFETY FIRST Your safety and the safety of others is very important. We have provided many important safety messages in this Job Aid and on the appliance. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.” These words mean: You can be killed or seriously injured if you WARNING don’t immediatel
Summary of the content on the page No. 6
MODEL & SERIAL NUMBER DESIGNATIONS MODEL NUMBER MODEL NUMBER MFW 9 6 00 S Q 0 PRODUCT GROUP M = Maytag ACCESS F = Front Loading T = Top Loading PRODUCT W = Washer SERIES 5 = LEAP 6 = Oasis 7 = 24" Front Load 8 = Mid Line Front Load 9 = Full Size Front Load PRICE POINT LEVEL (1-9) TRADE PARTNER ID 00 = Branded YEAR OF INTRODUCTION S = 2006, T = 2007 COLOR CODE B = Black Q = White ENGINEERING CHANGE SERIAL NUMBER SERIAL NUMBER CS T 32 02031 DIVISION = Schorndorf, Germany YEAR OF PRODUCTION T = 20
Summary of the content on the page No. 7
MODEL & SERIAL NUMBER LABEL AND TECH SHEET LOCATIONS The Model/Serial Number label and Tech Sheet locations are shown below. Model & Serial Number Label Location Tech Sheet Location (Behind Toe Panel) 1-3
Summary of the content on the page No. 8
SPECIFICATIONS
! "# "# $% & ' % !!( "# )* " )* " +!!) ,! ,! -$ .$)! % .%!( /!)$% ! $ $) !$% ! /!)$%0 1 *!% $% 2+'# 2'""3#2 2+'# 2'""3#2 1-4
Summary of the content on the page No. 9
MAYTAG CORPORATION MAJOR APPLIANCE WARRANTY ONE YEAR LIMITED WARRANTY For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or furnished with the product, Maytag Corporation or Maytag Limited (hereafter “Maytag”) will pay for Factory Specified Parts and repair labor to correct defects in materials or workmanship. Service must be provided by a Maytag designated service company. This limited warranty applies only when
Summary of the content on the page No. 10
— NOTES — 1-6
Summary of the content on the page No. 11
Gather the required tools and parts before starting installation. The parts supplied are in the washer drum. A pedestal will add to the total height of the washer for a total Pliers (that open to 1 9/16 " [39.5 mm]) height of 53.5" (135.9 cm). Flashlight (optional) Open end wrenches 17 mm and 13 mm Level Wood block Ruler or measuring tape
Summary of the content on the page No. 12
Selecting the proper location for your washer improves
performance and minimizes noise and possible washer “walk.”
Your washer can be installed under a custom counter, or in a basement, laundry room, closet, or recessed area. See “Drain The dimensions shown are for the recommended spacing. System.” Companion appliance location requirements should also be considered. Proper in
Summary of the content on the page No. 13
The washer can be installed using the standpipe drain system (floor or wall), the laundry tub drain system, or the floor drain The dimensions shown are for the recommended spacing. system. Select the drain hose installation method you need. See ?Tools and Parts. ?
! The standpipe drain requires a minimum diameter standpipe of 2
Summary of the content on the page No. 14
Do not ground to a gas pipe. Check with a qualified electrician if you are not sure the washer is properly grounded. Do not have a fuse in the neutral or ground circuit. * & ) ( $ This washer must be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of electrical shock by providing a path of least resistance for
Summary of the content on the page No. 15
Once the bolt is loose, move it to the center of the hole and Using pliers, tighten the couplings with an additional completely pull out the bolt, including the plastic spacer two-thirds turn. covering the bolt. Do not overtighten. Damage to the coupling can result. Once all 4 bolts are removed discard bolt and spacers. Then Turn on the water faucets and check for leaks. pull the power cord through the opening of the rear panel and Replace inlet hoses after 5 years of use to red
Summary of the content on the page No. 16
Drape the power cord over the washer top. Check the electrical requirements. Be sure that you have the correct electrical supply and the recommended grounding Secure the drain hose to the laundry tub leg or standpipe with method. See “Electrical Requirements.” the beaded strap provided. (See illustrations A and B.) Check that all parts are now installed. If there is an extra part, go back through the steps to see which step was skipped. Check that
Summary of the content on the page No. 17
# Flexible electronic controls are easy to use whether you are a This washer has a heating element that automatically heats the beginner or an expert. water to the best temperature on select cycles. This enables stepped cleaning, a process in which warm water is brought in and mixed with detergent first, then the water is heated. The warm water cleans stains such as blood and eggs, and the The Smart Dispensers make you
Summary of the content on the page No. 18
PRODUCT OPERATION THEORY OF OPERATION The flowmeter is also used to introduce addi- INTRODUCTION tional water into the tub for higher water levels, The Maytag Epic Front-Loading Automatic based on cycle requirements. Washer presents a number of new features and operating characteristics quite different from previous models. The washer contains a number of unique operating features designed to increase clothes cleaning ability while offer- ing very high water and energy conservation. WATER SYST
Summary of the content on the page No. 19
The dispenser drawer has four separate com- The water enters the wash tub through the partments for adding laundry products to the main inlet tube. wash load. These compartments are: 1. Prewash Detergent Compartment 2. Main Wash Detergent Compartment 3. Bleach Compartment 4. Fabric Softener Compartment Main Inlet Tube 1 3 AIR VENT SYSTEM 4 2 As a safety feature, the washer is designed to allow fresh air to circulate through the tub. An inlet vent at the rear of the washer brings air into the tub
Summary of the content on the page No. 20
The pressure switch also senses the suds level PRESSURE SWITCH in the wash tub. If excessive sudsing occurs, The pressure switch is located in the top right the washer starts an automatic suds routine. rear corner of the washer. This switch senses The display will show the word “Sud.” The water level in the wash tub. The control signal automatic suds routine adds additional rinse from the pressure switch is sent to the Central and drain operations until the suds level is Control Unit and is used
