Summary of the content on the page No. 1
3.5 GALLON PARTS WASHER
Assembly and Operating Instructions
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
® ®
Copyright 1997 by Harbor Freight Tools . All rights reserved. No portion of this manual
or any artwork contained herein may be reproduced in any shape or form without the
express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353.
Summary of the content on the page No. 2
SPECIFICATIONS Characteristic Value Tank Dimensions 17-3/8" x 14-1/4" x 8-3/4" Max. Solvent Capacity 3-1/2 Gallons Pump Output 50 GPH Electrical Requirements .7 Amps @ 110V, 60Hz Weight 15-1/2 lbs. SAVE THIS MANUAL You will need the manual for the safety warnings and READ ALL INSTRUCTIONS cautions, assembly instructions, operating procedures, BEFORE ASSEMBLING OR maintenance procedures, trouble shooting, parts list, and OPERATING THIS TOOL. diagram. Keep your invoice with this manual. Write the
Summary of the content on the page No. 3
8. USE EYE PROTECTION. Solvents can cause serious eye damage . Wear ANSI approved chemical splash safety goggles. Goggles are available from Harbor Freight Tools. When cleaning, be especially careful as solvents can be forcibly ejected from fluid and air passages. 9. DRESS SAFELY. Protective gloves and nonskid footwear or safety shoes must be used when working with and operating the Parts Washer. Don’t wear loose clothing or jewelry. They can get caught in moving parts. Also, wear a protective h
Summary of the content on the page No. 4
VOLTAGE WARNING Common household current is 110-120 volts. As long as your tool is rated from 110V-120V there will be no complications using this tool with household receptacles. If your tool is rated 220V-240V it has a completely different style of plug and must be used with a 220V-240V receptacle. Never try to plug a 110V-120V tool into a 220V-240V circuit (or vice-versa) or serious complications will arise, including possible injury to the operator. The plugs and receptacle have completely di
Summary of the content on the page No. 5
UNPACKING When unpacking, check to make sure the following parts are included. All sizes listed below are approximate. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual. NO. QTY. DESCRIPTION NA 1 Parts Washer and Pump Assembly NA 1 Cord and Switch Box Assembly NA 1 Work Shelf Assembly 7 1 Filter 9 1 Flexible Metal Spigot 10 1 Lid Handle 12 2 M5 x 12 Screw 13 2 M5 Lock Washer 14 2 M5 Nut 19 1 Cord Clamp 20 3 M4 x 8 Screw 21 3 M4 Washer
Summary of the content on the page No. 6
ASSEMBLY Lid Handle Assembly Step 1: Get out the LID HANDLE (#10); and two each of the SCREWS (#12), Lock Washers (#13), and NUTS (#14). Step 2: Attach HANDLE to LID (#2) as shown in Figure 1. Lid (#2) Screw (#12) Handle (#10) Lock Washer (#13) Nut (#14) Figure 1 — Attaching Handle to Lid SKU 35740 For technical questions, please call 1-800-444-3353. Page 6
Summary of the content on the page No. 7
Cord Clamp/Ground Wire Installation Step 1: As viewed from the inside, insert one SCREW (#20) through the right side of the CORD CLAMP (#19) and the inside of the TANK (#1). Make sure CORD CLAMP is covering the cord of the PUMP (#6). Step 2: On the outside of the TANK, put both ground wires (green with ring-ears) on the SCREW. Secure using (in the following order) a LOCK WASHER (#22), WASHER (#21), & NUT (#23). Step 3: Leave the other side of the CORD CLAMP unattached for now. Switch Box Wiri
Summary of the content on the page No. 8
Step 3: Attach the SWITCH BOX (#15) to the TANK (#1) using two SCREWS (#20), WASHERS (#21), LOCK WASHERS (#22), and NUTS (#23) as shown in Figure 3. Nut (#23) Black Wire (from Pump) White Wire (from Pump) Switch Box (#15) Power Cord (#17) Ground Screw Wires (#20) Lock Washer Washer (#22) (#21) Figure 3 — Attaching the Switch Box to Tank Step 4: When attaching the right side of the SWITCH BOX, make sure the SCREW also secures the side of the CORD CLAMP that was left unattached in Step 3, abov
Summary of the content on the page No. 9
Remaining Assembly Step 1: Attach the FILTER (#7) to the PUMP (#6), as shown in Figure 4. Step 2: Attach the SPIGOT (#9) to the PUMP, as shown in Figure 4. Step 3: Set the PARTS TRAY (#3) in the TANK (#1). Flexible Spigot (#9) Parts Tray Pump Unit (#3) (#6) Filter (#7) Figure 4 — Attaching the Remaining Parts OPERATIONS Step 1: Parts can soaked in the TANK (#1), but should not be left overnight. Step 2: Use the PARTS SHELF (#2) when using the FLEXIBLE SPIGOT (#9) and whenever cleaning sma
Summary of the content on the page No. 10
PARTS LIST NO. QTY. DESCRIPTION 1 1 Tank 2 1 Lid 3 1 Parts Shelf 4 1 Fusible Link Lid Arm 5 9 Rivet 6 1 Pump 7 1 Filter 8 1 Pump Bracket 9 1 Flexible Spigot 10 1 Lid Handle 11 2 Parts Shelf Handle 12 2 M5 x 12 Screw 13 2 M5 Lock Washer 14 2 M5 Nut 15 1 Switch Box 16 1 Switch 17 1 Power Cord 18 2 Strain Relief 19 1 Cord clamp 20 3 M4 x 8 Screw 21 3 M4 Washer 22 3 M4 Lock Washer 23 3 M4 Nut PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN TH
Summary of the content on the page No. 11
PARTS DIAGRAM NOTE: Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts. REV 06/05 SKU 35740 For technical questions, please call 1-800-444-3353. Page 11
