Pitco Frialator L80-029 user manual

User manual for the device Pitco Frialator L80-029

Device: Pitco Frialator L80-029
Category: Burner
Manufacturer: Pitco Frialator
Size: 2.74 MB
Added : 7/8/2014
Number of pages: 24
Print the manual

Download

How to use this site?

Our goal is to provide you with a quick access to the content of the user manual for Pitco Frialator L80-029. Using the online preview, you can quickly view the contents and go to the page where you will find the solution to your problem with Pitco Frialator L80-029.

For your convenience

If looking through the Pitco Frialator L80-029 user manual directly on this website is not convenient for you, there are two possible solutions:

  • Full Screen Viewing - to easily view the user manual (without downloading it to your computer), you can use full-screen viewing mode. To start viewing the user manual Pitco Frialator L80-029 on full screen, use the button Fullscreen.
  • Downloading to your computer - You can also download the user manual Pitco Frialator L80-029 to your computer and keep it in your files. However, if you do not want to take up too much of your disk space, you can always download it in the future from ManualsBase.
Pitco Frialator L80-029 User manual - Online PDF
Advertisement
« Page 1 of 24 »
Advertisement
Print version

Many people prefer to read the documents not on the screen, but in the printed version. The option to print the manual has also been provided, and you can use it by clicking the link above - Print the manual. You do not have to print the entire manual Pitco Frialator L80-029 but the selected pages only. paper.

Summaries

Below you will find previews of the content of the user manuals presented on the following pages to Pitco Frialator L80-029. If you want to quickly view the content of pages found on the following pages of the manual, you can use them.

Abstracts of contents
Summary of the content on the page No. 1

IMPORTANT FOR FUTURE REFERENCE
Please complete this information and retain these
instructions for the life of the equipment:
Model #: __________________________
Serial #: __________________________
Date Upgraded: ___________________
Technician: _________________________
Installation Instructions for the
PITCO
Self-Cleaning Burner System
L80-029 Rev 5 10/07
E N G L I S H

Summary of the content on the page No. 2

RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE WARNING The power supply to the appliance MUST be disconnected before performing this procedure. WARNING Ensure that the gas supply to this appliance is turned off before performing this procedure. WARNING Use only parts supplied with this kit. Use of any parts other than those supplied with this kit will void the warranty and could cause unsafe conditions or improper operation of your appliance. WARNING Drain the tank and ensure that appliance has

Summary of the content on the page No. 3

Theory of Operation: A natural gas burning appliance requires roughly 10 cubic feet of air to properly combust a single cubic foot of gas. Minute airborne particles entrained during this process pass through the combustion system and are incinerated. However, some particles may be trapped within the combustion system, building up over time, causing an eventual decrease in the operational efficiency of your appliance. The rate at which this build up may occur varies from kitchen to kitchen and is

Summary of the content on the page No. 4

Follow this procedure for Installation of Self Cleaning burners and SCBS arm: a. Disconnect the control harness from the main gas valve and tuck it out the way to avoid damaging the harness during this procedure. b. If your appliance has a solid-state control (or auxiliary thermostat) behind the door, remove it at this time. With a 5/16” nut driver remove the two self-threading screws that mount the control to the appliance, disconnect the control harness and tuck it out of the way to avoid dama

Summary of the content on the page No. 5

e. Using a 1 1/16” wrench and a 7/8” wrench, loosen the brass fitting on the top of the gas valve and disconnect the gas valve from the manifold inlet. This will allow you to drop the gas valve down and keep it out of the way during burner replacement. f. Using a 5/16” wrench, nut driver or screw gun bit, remove all burners by removing the (2 ea.) self threading screws holding them into the burner rack. Retain these for reinstallation of the new burners. Note: On models MG2 and SGH50, it will b

Summary of the content on the page No. 6

i. Capture the remaining burners on the SCBS Arm in the same manner as in step h, and secure them into the appliance, taking care not to strip the pre-threaded holes. j. Secure the SCBS Arm to left side of the burner to the right of the pilot using two 10 X 24 self-threading screws provided with the Pitco Self-Cleaning Burner System Upgrade Kit. The SCBS Arm should now be mounted properly and securely. Inspect your work to insure that the burners are installed correctly. Improperly mounted or po

Summary of the content on the page No. 7

NOTE: CE approved models will have a pressure test fitting in this location. For CE approved models, remove this pressure test fitting using a 7/16” (12 mm) wrench. Using a 3/16” (5 mm) hex key, remove the plug from the auxiliary pressure tap on the manifold inlet and replace it with pressure tap fitting that you removed from the TOP (Outlet side) of the valve. Use teflon tape or apply pipe joint compound on the threads of the fitting to ensure a gas-tight seal. b. Remove the straight 1/8” NPT X

Summary of the content on the page No. 8

e. Thread the compression nut on the corrugated tubing end of the SCBS Valve Assembly onto the orifice assembly that you inserted into the runner tube in step c and tighten with a 1/2” (13 mm) wrench. f. Install the orifice retainer bracket onto the pilot bracket and SCBS Orifice assembly. This will secure the orifice assembly into the runner tube. g. Tighten ALL joints on the SCBS Valve assembly with a ½” (13 mm) wrench. Reinstall the pilot tubing into the gas valve. h. Reconnect the control ha

Summary of the content on the page No. 9

b. Disconnect the wiring harness from the relay board mounted behind the front panel and remove the relay board and insulation paper. Be sure to retain the screws. The existing relay board may or may not have a jumper plug as shown. If it does, remove it from the old relay board and install it into the same position on the “new” SCBS relay board provided. c. Install the insulation paper provided with the Pitco Self-Cleaning Burner System Upgrade Kit onto the backside of the SCBS Control Board an

Summary of the content on the page No. 10

e. If the appliance you are upgrading does NOT have a Solid State Control, proceed to step f in this section. If the appliance that you are upgrading has a Solid State Control, feed the other ends of the SCBS Harness through the unused portion of the strain relief holding the Solid State Control Harness and proceed directly to step h in this section. NOTE: If needed, you can carefully nudge open the area in the strain relief with a screwdriver to make additional room to insert the SCBS harness.

Summary of the content on the page No. 11

i. Connect the SCBS Harness to the SCBS Valve as shown. The red and violet wires must be connected to the vertically oriented tabs on the valve and the green (ground) wire must be connected to the bottom, horizontally oriented tab on the valve. The grey wires will be connected to the Thermal Limit at a later point in the upgrade process. j. Route the SCBS Harness along the main control harness and wire tie it to the control harness. The proper wire tie locations are indicated by arrows, see phot

Summary of the content on the page No. 12

Follow this procedure to check proper operation of the Pitco Self-Cleaning Burner System: WARNING Ensure that tank is filled to the level line with oil before turning the appliance on. Turning the appliance on with an empty or partially filled tank could cause an unsafe condition, which could lead to damage to the appliance, property damage or personal injury. a. Reconnect the power supply and turn on the gas supply to the appliance. b. Energize the unit and check the gas delivery system and Pit

Summary of the content on the page No. 13

appliance is in operation, or can be detected visually by watching the burner flame through the air collars. The sound of the burners will be inconsistent and the flame may appear to ‘peel’ off of the burner face. A certain amount of flame roll out during ignition is normal. However, excessive flame roll out during burner operation is abnormal. Excessive flame roll out will cause undue heating in the burner area and will cause the thermal cut out switch to trip. If there is significant flame rol

Summary of the content on the page No. 14

TROUBLESHOOTING Should there be a problem with your appliance, use the following tables to isolate possible faults before calling Pitco Technical Support. POSSIBLE CAUSES CORRECTIVE ACTION PROBLEM A. Main breaker in OFF position. A. Turn on Circuit Breaker to appliance. B. Gas supply turned OFF. B. Turn on gas supply to appliance. Appliance will not C. Appliance unplugged. C. Plug appliance power cord into wall outlet. run, front panel D. Blown control fuse. D. lights are not ON. Refer to Serv

Summary of the content on the page No. 15

13 L80-029 Rev 5 10/07

Summary of the content on the page No. 16

L80-029 Rev 5 10/07 14

Summary of the content on the page No. 17

15 L80-029 Rev 5 10/07

Summary of the content on the page No. 18

L80-029 Rev 5 10/07 16

Summary of the content on the page No. 19

17 L80-029 Rev 5 10/07

Summary of the content on the page No. 20

L80-029 Rev 5 10/07 18


Alternative user manuals
# User manual Category Download
1 Adams Speedflame Power Gas User manual Burner 3
2 Adams Mark 10 User manual Burner 1
3 AEG 3531 WK-M GB 949600835 User manual Burner 4
4 APW GHP-2H User manual Burner 3
5 APW GHPW-2H User manual Burner 2
6 APW GHP-4H User manual Burner 1
7 Bacharach MZF User manual Burner 2
8 Beckett 800 User manual Burner 10
9 Beckett AFII 100 User manual Burner 11
10 Beckett CF375 User manual Burner 8
11 Beckett AFG 240V User manual Burner 12
12 Beckett AFG User manual Burner 28
13 Beckett 150 User manual Burner 0
14 APW GHP-6H User manual Burner 2
15 Beckett CF800 User manual Burner 15