Summary of the content on the page No. 1
www.proform.com
Model No. PFTL20511.0
Serial No.
USER’S MANUAL
Write the serial number in the space
above for reference.
Serial Number
Decal
QUESTIONS?
If you have questions, or if parts
are damaged or missing, DO NOT
CONTACT THE STORE; please
contact Customer Care.
IMPORTANT: Please register this
product (see the limited warranty
on the back cover of this manual)
before contacting Customer Care.
CALL TOLL-FREE:
1-888-533-1333
Mon.–Fri. 6 a.m.–6 p
Summary of the content on the page No. 2
TABLE OF CONTENTS WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 IMPORTANT PRECAUTIONS ..................................................................3 BEFORE YOU BEGIN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 PART IDENTIFICATION CHART. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Summary of the content on the page No. 3
IMPORTANT PRECAUTIONS WARNING: To reduce the risk of serious injury, read all important precautions and instructions in this manual and all warnings on your treadmill before using your treadmill. ICON assumes no responsibility for personal injury or property damage sustained by or through the use of this product. 1. Before beginning any exercise program, other electrical devices, except for low-power consult your physician. This is especially devices such as cell phone chargers, into im
Summary of the content on the page No. 4
20. The heart rate monitor is not a medical 28. Over exercising may result in serious injury device. Various factors, including the user’s or death. If you feel faint or if you experience movement, may affect the accuracy of heart pain while exercising, stop immediately and rate readings. The heart rate monitor is cool down. intended only as an exercise aid in determin- ing heart rate trends in general. 29. Do not store the television in temperatures below -40° F (-40° C) or above 140° F (60
Summary of the content on the page No. 5
34. Upon completion of any service or repairs to 38. Use a jumper wire not smaller than No. 6 2 the treadmill or the television, ask the ser- AWG (13.3 mm ) copper, or the equivalent, vice technician to perform safety checks to when a separate antenna-grounding elec- confirm that the unit is in proper operating trode is used. See NEC Section 810-21 (j) or condition. your local codes and ordinances. 2 35. Use No. 10 AWG (5.3 mm ) copper, No. 8 AWG 39. Note to CATV system installer: This remind
Summary of the content on the page No. 6
BEFORE YOU BEGIN Thank you for selecting the revolutionary reading this manual, please see the front cover of this ® PROFORM PERFORMANCE 1850 treadmill. The manual. To help us assist you, please note the product PERFORMANCE 1850 treadmill offers an impres- model number and serial number before contacting us. sive selection of features designed to make your The model number and the location of the serial num- workouts at home more enjoyable and effective. And ber decal are shown on the front c
Summary of the content on the page No. 7
PART IDENTIFICATION CHART Use the drawings below to identify small parts used for assembly. The number in parentheses below each draw- ing is the key number of the part, from the PART LIST near the end of this manual. The number following the key number is the quantity used for assembly. Note: If a part is not in the hardware kit, check to see if it is preat- tached. Extra hardware may be included. 1/4" Star 5/16" Star 5/16" Flat 3/8" Star 3/8" Nut (12)–2 Washer (35)–6 Washer (11)–4 Washer (
Summary of the content on the page No. 8
ASSEMBLY • To hire an authorized service technician to • To identify small parts, see page 7. assemble the treadmill, call 1-800-445-2480. • Assembly requires the following tools: • Assembly requires two persons. the included hex key • Place all parts in a cleared area and remove the packing materials. Do not dispose of the packing one adjustable wrench materials until you finish all assembly steps. one Phillips screwdriver • After shipping, there may be an oily substance on the exte
Summary of the content on the page No. 9
3. Identify the Left Upright (89), which is marked 3 with a “Left” sticker or an “L” sticker. Have a sec- ond person hold the Left Upright near the 81 Base (94). 89 See the inset drawing. Tie the wire tie in the Wire Left Upright (89) securely around the end of the 81 Tie Upright Wire (81). Then, pull the other end of the wire tie until the Upright Wire is routed through Wire the Left Upright. Tie 89 81 94 4. Hold the Left Upright (89) against the Base (94). 4 Be careful not to pi
Summary of the content on the page No. 10
5. Identify the Left Base Cover (82) and the Right 5 Base Cover (83). Slide the Left Base Cover onto the Left Upright (89). Slide the Right Base Cover onto the Right Upright (90). Do not press the 80 Base Covers into place yet. Identify the Left Upright Cover (79) and the Right Upright Cover (80). Slide the Left Upright 90 Cover onto the Left Upright (89). Slide the Right 89 Upright Cover onto the Right Upright (90). 79 83 82 6. Cut the plastic ties in the Left Handrail (88) and 6 the
Summary of the content on the page No. 11
7. Attach the Left Handrail (88) to the Left Upright 7 (89) with two 5/16" x 1" Screws (5), two 5/16" 4 Star Washers (11), and a 5/16" x 1 1/4" Bolt (4). 11 87 Do not tighten the Screws and Bolt yet. Attach the Right Handrail (87) in the same 5 5 way. 11 88 4 89 8. Set the console assembly face down on a 8 soft surface to avoid scratching the console Console assembly. Assembly Remove all of the screws (B) attaching the Crossbar (93). Next, lift off the Crossbar. Discard B the Scre
Summary of the content on the page No. 12
10. With the help of a second person, hold the con- 10 sole assembly near the Left Handrail (88). Connect the Upright Wire (81) to the console Console wire. See the inset drawing. The connectors Assembly should slide together easily and snap into place. If they do not, turn one connector and try again. IF YOU DO NOT CONNECT THE CON- NECTORS PROPERLY, THE CONSOLE MAY BECOME DAMAGED WHEN YOU TURN ON THE POWER. Remove the wire tie from the Console Upright Wire. Wire Coaxial Cables Conn
Summary of the content on the page No. 13
13. Slide the Left Handrail Cover (85) onto the Left 13 Handrail (88). Slide the Right Handrail Cover (86) onto the Right Handrail (87). Attach each Handrail Cover with a #8 x 1/2" Screw (1). 86 87 1 85 88 1 14. Hold the Left Upright Cover (79) against the 14 console assembly. Align the holes in the Left Upright Cover with the holes in the Left Upright (89). Attach the Left Upright Cover with three #8 x 1/2" Screws (1). Attach the Right Upright Cover (80) to the Right Upright (90)
Summary of the content on the page No. 14
16. IMPORTANT: See page 18 and plug in the 16 power cord. Next, see page 22 and turn on IMPORTANT: the power. Make sure to follow all instructions in this step. See page 30; follow steps 1, 2, and 4. When the frame stops moving, remove the key from the console and unplug the power cord. 17. IMPORTANT: Before you begin this step, 17 make sure that you have read and followed 56 all of the instructions in step 16. Raise the Frame (56) to the position shown. Have a second pers
Summary of the content on the page No. 15
18. Attach the Rear Feet (57) to the Frame (5 6) as 18 shown with four #8 x 3/4" Screws (2). Lower the Frame (56) (see HOW TO LOWER THE TREADMILL FOR USE on page 37). 57 57 2 2 56 19. Press the Grommet (77) into the square hole in 19 the Base (94). 94 77 20. Remove the #8 x 1/2" Machine Screw (1 14) and 20 the Wire Cover (117) from the TV Bracket (118). 115 With the helpf of a second person, hold the TV (119) near the TV Bracket (118) and insert the wires from the TV down through t
Summary of the content on the page No. 16
21. With the help of a second person, hold the TV 21 assembly near the console assembly, and con- TV Assembly nect the wires. Attach the TV assembly to the back of the con- sole assembly with four 1/4" x 3/4" Screws (116). Be careful not to pinch any wires. Start all Console four Screws, and then tighten them. Assembly Wires 116 22. Place the treadmill near the coaxial cable from 22 your wall (or device). Connect the coaxial cable to the Upright Coaxial Cable (122). Press the Right Ba
Summary of the content on the page No. 17
THE CHEST HEART RATE MONITOR HOW TO PUT ON THE HEART RATE MONITOR • Do not expose the heart rate monitor to direct sun- light for extended periods of time; do not expose it to The heart rate temperatures above 122° F (50° C) or below 14° F monitor consists of (-10° C). a chest strap and a Chest sensor. Insert the • Do not excessively bend or stretch the sensor when Strap Tabs tab on one end of using or storing the heart rate monitor. the chest strap into the hole in one end • T o cl
Summary of the content on the page No. 18
HOW TO CONNECT THE TREADMILL HOW TO CONNECT THE POWER CORD nominal 120-volt circuit capable of carrying 15 or more amps. To avoid overloading the circuit, do Use a Surge Suppressor not plug other electrical devices, except for low- power devices such as cell phone chargers, into Your treadmill, like other electronic equipment, can be the surge suppressor or into an outlet on the same damaged by sudden voltage changes in your home’s circuit. IMPORTANT: The treadmill is not compat- power. Volt
Summary of the content on the page No. 19
Before operating the 15" digital TV, you must connect an antenna or a 75 ohm CATV cable to the 75 ohm terminal, an AV cable to the audio/video input jack, or an HDMI cable to the HDMI input jack. Note: Use a CATV cable to connect to an external source such as a cable box, satellite TV box, VCR, or analog cable. No CATV cable, antenna, or adapter; AV cable; or HDMI cable is included. HOW TO CONNECT AN ANTENNA 2. Push the 300 ohm 300 to 75 Ohm Adapter to 75 ohm adapter Place an indoor onto
Summary of the content on the page No. 20
HOW TO CONNECT A VCR, DVD PLAYER, OR HOW TO CONNECT A DVD OR BLU-RAY PLAYER OTHER DEVICE USING AN AV CABLE OR OTHER DEVICE USING AN HDMI CABLE 1. Connect the three-pronged end of an RCA AV 1. Connect one end of an HDMI Cable to your DVD or Cable to your VCR, DVD player, or other device. Blu-ray player or other device. 2. Plug in the power cord of your device. See your 2. Plug in the power cord of your device. See your VCR, DVD player, or other device’s user’s manual DVD or Blu-ray player
