Summary of the content on the page No. 1
™
Affinity
Owner's Manual
Summary of the content on the page No. 2
IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS WARNING: RISK OF ACCIDENTAL INJURY OR DROWNING; CHILDREN SHOULD NOT USE HYDROMASSAGE BATHTUB WITHOUT ADULT SUPERVISION. WARNING : TO AVOID INJURY, EXERCISE CAUTION WHEN ENTERING OR EXITING THE HYDROMASSAGE BATHTUB WARNING: RISK OF ACCIDENTAL INJURY OR DROWNING; DO NOT USE HYDROMASSAGE BATHTUB UNLESS ALL SUCTION GUARDS ARE INSTALLED TO PREVENT BODY AND HAIR ENTRAPMENT. WARNING: KEEP BODY AND HAIR A MINIMU
Summary of the content on the page No. 3
Contents Specifications & Rough-in Reference _____________________________________________________ 2 Framing and Support _________________________________________________________________ 3 Wall Cutout & CD/Radio Installation ______________________________________________________ 4-5 TV Installation _______________________________________________________________________ 6 Service Access ______________________________________________________________________ 7 Electrical ___________________________
Summary of the content on the page No. 4
Specifications & Rough-in Reference DIMENSIONS 68" (1727 mm) L 68" (1727 mm) W 22" ( 559 mm) H1 68" 68" 27" ( 686 mm) H2 35-7/8" ( 911 mm) H3 DRAIN/OVERFLOW DIMENSIONS DRAIN/OVERFLOW 19" (483 mm) A CUTOUT 16" X 4" 12" (305 mm) B TOTAL WEIGHT/FLOOR LOADING 34" 11-7/8" 1500 lb 34" (682 kg)/ 24" 47 lb/sq. ft. 8-3/8" 48" (229 kg/sq. m) TOP VIEW OPERATING SENSOR FOR GALLONAGE REMOTE CONTROL 120 U.S. gal (455 liters) H3 H1 PRODUCT WEIGHT H2 250 lb (114 kg) FRONT VIEW ELECTRICAL REQUIREMENTS BATH 11
Summary of the content on the page No. 5
Important: Read complete instructions before beginning installation. Each whirlpool bath arrives ready for installation, completely equipped with motor/pump assembly and plumbing and fittings necessary for whirlpool operation. An optional drain/overflow kit is available for installation on the bath. Remove the bath from the carton. Retain the shipping carton until satisfactory inspection of the product has been made. Do not lift the bath by the plumbing at any time; handle by the shell only
Summary of the content on the page No. 6
Wall Cutout and CD/Radio Installation The installation requires a cutout in the wall. The cutout allows room for the speakers, CD/Radio speaker/power & TV audio cable wires. NOTE: CD/Radio must be must be located a minimum of 5' away from the interior of the bath. The cable provided with the unit is designed for this minimum distance. If a longer distance is desired, cut the cable and splice to the power cord with leads provided with the CD/radio. Do not exceed 20' as the CD/radio audio per
Summary of the content on the page No. 7
Remove trim plate. Remove sleeve after disengaging sleeve locks. Stand the unit and insert the 2 handles between the unit and sleeve to disengage the sleeve locks. When standing the unit be careful not to damage the fuse on the rear. Remove the sleeve. Retain the handles for future use. Run wires through sleeve. Insert sleeve into build out. When flush, bend appropriate tabs to hold sleeve firmly in place. Connect the speaker & power connector and TV audio to the CD/radio. Connect the gre
Summary of the content on the page No. 8
TV Installation Remove back cover by lifting straight upward and then DRIP SHIELD WIRING remove the drip shield. Tighten cable tie and cut off excess. Tighten cable tie with anchor (not supplied) to DRIP SHIELD the TV power cord. It is not necessary to attach anchor to drip shield; the cable tie and anchor are used to FAN ensure the TV power cord remains in the TV housing. BLACK Locate blackout panel and peel protective backing off TV POWER CORD RED adhesive. Position blackout panel onto TV
Summary of the content on the page No. 9
Bonding Service Access 2 Connect a #8 guage (10mm ) minimum solid copper For partially or fully sunken installations, allow for ac- bond wire from the house electrical pannel or an ap- cess to service connections. It is the installer's respon- proved local ground to all metal components (i.e. junc- sibility to provide sufficient service access. See Ser- tion box etc.). An approved ground may be an 8 foot long vice Access illustration. Provide adequate ventilation ground rod (3 meter long ear
Summary of the content on the page No. 10
2" Drain Information Clean-Up After Installation A drain/overflow assembly must be installed on the bath, To avoid dulling and scratching the surface of the bath, water tested, and connected to the sanitary system of never use abrasive cleaners. A mild liquid detergent the house. After opening the carton, inspect for dam- and warm water will clean soiled surfaces. age and verify that the kit is of the proper finish. In the Remove spilled plaster with a wood or plastic edge. Jacuzzi Whirlpool
Summary of the content on the page No. 11
Remote Control LED INDICATOR POWER TV MODE BATH MODE CHANNEL UP & DOWN VOLUME UP & DOWN JETS FUNCTION CD/DVD FUNCTION BLOWER FUNCTION LIGHT FUNCTION The Floating Remote Control is a universal remote control that has been programmed to operate the TV. If the remote has been deprogrammed the following procedure will reprogram the remote: For TV 1. Press and release the TV button. 2. Press and hold the BLOWER button. The LED will flash. 3. While holding the BLOWER button, press the POWER but
Summary of the content on the page No. 12
PURGES TV Automatic Purge The Floating Remote will control the volume and change the channels of the TV. With all functions off either, manually or by program, a 60 minute timer will be initiated. Once this timer is fin- For complete operation of the TV consult the manual ished, a 1 minute purge will be activated (blower) to enclosed. purge any remaining water in the air channel. If any Note: The TV manufacturer’s remote is not intended to key is pressed the purge timer will be reset. be use
Summary of the content on the page No. 13
CD/Radio Controlling Whirlpool Action For operation of the CD/radio consult the manual en- The whirlpool action in your bath is influenced by three closed. factors – direction of flow, force of water, and force of Note: The remote for the CD/radio is not intended to air. be used inside the bath. Direction: To change the direction of the water flow, Note: For units with AM/FM radios, the quality of AM swivel the jet nozzle to the desired angle. The jets can reception will vary by locality. J
Summary of the content on the page No. 14
BATH MAINTENANCE Cleaning the Bath Bath Additives To clean your bath, simply use a mild, nonabrasive liq- NOTE: DO NOT USE OIL OR OIL BASED BATH uid detergent solution. You can protect and restore the ADDITIVES. gloss to a dulled acrylic surface by applying Meguiar's If you want to use any kind of bath additive, use only a #10 Mirror Glaze, a product specifically designed for small amount of low-foaming powder or crystal sub- use on acrylic finishes. If Meguiar's is not available, an stance;
Summary of the content on the page No. 15
Suction Cover/Strainer Maintenance Lamp Clean the suction cover/strainer of hair and debris when When the bulb burns out, replace it from the back of necessary. To do this, remove the center screw and the lamp fitting, on the underside of the shell, by pulling detach the square cover. Clean the cover by backflush- out the bulb receptacle. Replacement bulbs (7W, 12V) ing debris from the holes. Replace the suction cover are available from your Jacuzzi Whirlpool Bath dealer. immediately after c
Summary of the content on the page No. 16
14
Summary of the content on the page No. 17
15 TEMPLATE FOR CD/RADIO MOUNTING SLEEVE 182 mm 53 mm
Summary of the content on the page No. 18
Summary of the content on the page No. 19
Jacuzzi Whirlpool Bath Limited Warranty Designer Collection Bath Product WARRANTY COVERAGE Jacuzzi Whirlpool Bath (the “Company”) offers the following express limited warranty to the original purchaser of any Jacuzzi Whirlpool Bath Designer Collection Bath Product (“unit”) who purchases the product for personal or single family use (“user”). The Company will repair or replace, at its option, the unit or its equipment in accordance with the following terms and conditions. TWO YEAR LIMITED WARRANT
Summary of the content on the page No. 20
Warranty Registration Card This card must be filled out and returned to the address printed on the other side within thirty (30) days from date of purchase in order for this warranty to be come effective. Purchaser's Name ________________________________________ Purchaser's Address _______________________________________ City _____________________________ State _____ Zip ________ Date of Purchase _________________________________________ Model Name _____________________________________________ S
