Summary of the content on the page No. 1
User Instruction & Installation Manual
FR380 Remote Control Explorer
Tungsten Halogen Searchlight
Product Reference Number:
A2542 – FR380RC Explorer 115/240v 650/1000w
A2541 – FR380RC Explorer 24v 150/250w
Manufacturers details: Distributor details:
Francis Searchlights Ltd
Union Road, Bolton
Lancashire, BL2 2HJ, UK
Tel: +44 (0) 1204 558960
Fax: +44 (0) 1204 558979
http://www.francis.co.uk
E-mail: sales@francis.co.uk
Manual Part Number: C23299
Issue : 3
Summary of the content on the page No. 2
CONTENTS 1 - Introduction 2 - Safety Precautions 3 - Technical Information 4 - Unpacking and Installation Instructions 5 - Electrical Installation 6 - Operating Instructions 7 - Fault Finding 8 - Maintenance and Servicing 9 - Wiring Diagrams & General Assembly 10 - Spare Parts List
Summary of the content on the page No. 3
1 - Introduction It is imperative that this manual is read carefully and understood before installing your equipment. For your future reference please keep this manual in a safe place. Thank you for specifying a product from the Francis Searchlights range. All Francis products are designed to give complete customer satisfaction and are manufactured to the highest engineering standards in order to ensure optimum performance and service life. The Francis FR range combines features proven over many
Summary of the content on the page No. 4
2 - Safety Precautions The following instructions must be adhered to, in order to ensure a safe working environment and the safety of the user. Note: When unpacking or manoeuvring the searchlight into its fixing position, suitable lifting points must be used in order to prevent damage to the equipment or personal injury. Prevent rain, snow, condensation and water droplets from contacting the lamp as this may cause bulb failure and possible shattering; Quartz halogen bulbs run with a high inte
Summary of the content on the page No. 5
3 - Technical Information This product has been designed to operate in accordance with the product specification. The FR380RC searchlight has the following features: All marine grade materials and fixings; Parabolic glass reflector; Stove enamel painted; 365° horizontal rotation; Vertical movement +25° to -25°; Motor speed 20 °/sec (Pan). ,5 °/sec (Tilt); Remote focus facility; Thermostatically controlled internal heater.(Optional); Toughened front glass; The 24v searchlight also perfor
Summary of the content on the page No. 6
4 - Unpacking and Installation Instructions The following instructions should be read and fully understood prior to installing the equipment to ensure that the correct procedures are followed and all safety precautions are observed. Note: If the equipment has been in storage for a considerable amount of time, it is advisable to conduct a routine maintenance check on all parts before installation. Safety Precautions This equipment should not be connected to an electrical supply before being insta
Summary of the content on the page No. 7
5 - Electrical Installation For safety purposes, only competent personnel should perform the electrical installation. All equipment should be installed to current Electrical Regulations and Standards. In order to obtain the maximum light output from the searchlight, it is essential that the full operating voltage of the lamp fitted be applied to the lampholder contacts. Method of Electrical Connection 1) Disconnect the supply before working on the electrical system; 2) The searchlight must be
Summary of the content on the page No. 8
Installation Guidelines A typical installation and connection routine for the FR380RC Low Voltage searchlight is as follows: Referring to wiring diagram C23291, a supply is fed to the control panel, which then provides a common feed to the motor gearbox and the searchlight. The searchlight has been pre-wired with 3 meters of cable from the gearbox to junction box provided. Cables required to be connected by the customer: - 4 core 1.5mm cable from the junction box to the Control Panel. 12 cor
Summary of the content on the page No. 9
6 - Operating Instructions This equipment is designed for use out of doors, in free air. Never place anything on, or cover the searchlight when in use as this may present a hazard. The searchlight can be remotely positioned via the joystick control panel, with the facility for movement up, down, left and right. When in the desired position the joystick should be released so that it returns to its’ home position, dead centre. The beam of the searchlight can be adjusted to give a variety of beam t
Summary of the content on the page No. 10
When fitting the lamp: - Always isolate the equipment from the supply when inserting a lamp; - Ensure the circuit is suitably fused; - Ensure the lamp is of the correct power rating and type; - Check lampholder is in good condition. If the contacts show any sign of corrosion, replace the lampholder; - Check the lampholder is in a good dry condition. Never allow water to collect in the lamp fitting or come into contact with the lamp. To fit the lamp: - Loosen all the thumbscrews on the front of t
Summary of the content on the page No. 11
7- Fault Finding All fault finding must be conducted by a competent person or qualified Electrical Engineer. Failure of Lamp to light Causes: 1) Power not supplied; 2) Fuse blown; 3) Failed lamp Remedy: 1) Check voltage at supply. If supply is not present the fault is at the customer supply. If power is present, see remedy 2; 2) Check fuse for visual failure. If none noticeable check fuse for continuity using a multi-meter. If fuse found to be faulty, replace with new part and test equipment ag
Summary of the content on the page No. 12
8 - Maintenance and Servicing In order to prolong the service life and performance of your searchlight, the following maintenance guidelines are recommended: Maintenance checks should be conducted before very voyage or at least every three months; Before checking, disconnect the equipment from the supply; Visually inspect the condition of the equipment; Any major or minor structural damage should be rectified immediately in order to reduce sympathetic wear; After inspection it may be necess
Summary of the content on the page No. 13
9 - Wiring Diagrams and General Assembly Drawing Number Description A2542 FR380RC Explorer H.V G.A A2541 FR380RC Explorer L.V G.A C23293 H.V Explorer RC Wiring Diagram C23291 L.V Explorer RC Wiring Diagram C22848 High Voltage Control Panel C22431 Low Voltage Control Panel C23603 Junction Box Assembly
Summary of the content on the page No. 14
Summary of the content on the page No. 15
Summary of the content on the page No. 16
Summary of the content on the page No. 17
Summary of the content on the page No. 18
Summary of the content on the page No. 19
Summary of the content on the page No. 20
Back To Top
