Summary of the content on the page No. 1
P3PC-2242-01EN
( ) ( )
fi-6670 A /fi-6770 A /fi-6750S
Thank you for purchasing a fi-6670(A) / fi-6770(A) / fi-6750S Color Scanner
series. This Getting Started is the startup guide that summarizes the preparatory
actions needed before use. Be sure to thoroughly read this manual before you
start using the scanner.
Contents
Introduction....................................................................2
Regulatory Information .................................................2
Conventions.......
Summary of the content on the page No. 2
Error Recovery Details the status of the scanner and Introduction Guide (HTML explains how to resolve problems encoun- help) tered. Thank you for purchasing our fi-6670(A)/fi-6770(A)/fi-6750S series Contains movies that explain how to Color Image Scanner. replace the consumables. Included in the SETUP DVD-ROM. Help - Embedded Explains how to use the scanner drivers, Scanner Models in scanner drivers and how to configure the settings for them. This manual covers the following five scanner mod
Summary of the content on the page No. 3
Conventions assumes no liability whatsoever for damages arising from use of this product by the user in high-safety applications, and for any The use of a shielded interface cable is required to claims or compensation for damages by the user or a third party. comply with the Class B limits of Part 15 of FCC rules. The length of the Power cable must be 3 meters (10 feet) or less. Conventions Canadian DOC Regulations This digital apparatus does not exceed the Class B limit for radio Symbols U
Summary of the content on the page No. 4
*1) Where there is no distinction between the different versions of the above The user must not perform repairs on this scanner. operating system, the general term "Windows" is used. Contact the store where you purchased the scanner or an autho- *2) All the descriptions in this manual assume the usage of Adobe Acrobat rized FUJITSU Image Scanner service provider to make repairs to bundled with this product. However, Adobe Acrobat may be upgraded without notice. If the descriptions differ fro
Summary of the content on the page No. 5
Safety Information Safety Information Use the scanner only at the indicated power voltage. Do not connect to multiple-power strips. Warning Indications Used In This Use the scanner only at the indicated power voltage and current. Improper power voltage or Manual current might cause fire or electric shock. Do not connect to multiple-power strips. The following indications are used in this manual to obviate any change of accident or damage to you and/or the equipment. Do not touch the Power
Summary of the content on the page No. 6
Unplug the scanner when a trouble occurs. Immediately unplug the scanner when a trouble The following are important cautions described in this manual occurs. Never cut the ground connection until the scanner is unplugged from the Power outlet. Do not install the scanner on an unstable work table. Do not disassemble the scanner. When installing the scanner on a work table, make Do not take apart or modify the scanner. The sure that the table is flat and level. Place the inside of the scann
Summary of the content on the page No. 7
Safety Information Disconnect the power plug from the Power outlet when the scanner is not in use for a long period of time. When the scanner is not going to be used for a long period of time, be sure to disconnect the power plug from the Power outlet. Do not install the scanner in direct sunlight. Do not install the scanner under direct sunlight or near heating apparatus. Doing so might cause excessive heat to build up inside the scanner, which can cause scanner trouble or even fire. I
Summary of the content on the page No. 8
1 Preparation Contents of the Scanner Package When you open the scanner package, handle the main unit and its attachments carefully. Make sure the scanner package contains all the parts listed in the package contents list that is included in the package box. If any parts are missing or defective, contact your FUJITSU scanner dealer or an authorized FUJITSU scanner service provider. Part Names and Functions This section describes the scanner parts and their functions. For information on the fu
Summary of the content on the page No. 9
1 Preparation ■ fi-6770/fi-6770A/fi-6750S (Flatbed type) Chute Roller Cover ADF (automatic document feeder) ADF Paper Chute Stacker Paper Chute Stacker Extension Extension Side Guide Side Guide Button Stopper Operator Panel Flatbed Transport Lock Document Cover ADF Lock Screw Handle Document Holding Pad Lock Screw Storage Hole Document Bed ADF Open Button fi-6770 SCSI ID Switch CGA Board Slot SCSI Connector 1 USB Connector 1 fi-6770A CGA Board Ventilation Port Power Connector Main Power Swi
Summary of the content on the page No. 10
■ Model-Common Parts Brake Roller (x1) (consumable) Pick Arm (x1) Brake Roller Holder (x1) Ultrasonic Sensor (x2) Feed Roller (x4) (for multifile detection) Plastic Roller (x4) Chute Roller (x1) (Usually covered with a hood) Glass (x2) Pick Roller Cover (x1) Sheet Guide (x2) Pick Roller (1 x 2 types) (consumable) Functions of the Operator Panel The Operator Panel is comprised of a Function Number Display, buttons, and LEDs, which are used to operate the scanner and to check the scanner status.
Summary of the content on the page No. 11
1 Preparation ■ Flatbed type Check Check LED Function Number Display Function [Function] button Send to [Send to] button Scan / Stop [Scan/Stop] button Power [Power] button/Power LED Name Description Check LED Lights (in orange) when an error occurs. Function Number Display Indicates the scanner status. [Function] button Switches the function activated by the [Send to] button. Launches linked application software for scanning. [Send to] button Resets an error indication. Launches linked applicat
Summary of the content on the page No. 12
2 Installing the Scanner The following describes how to install the scanner. 1 Place the scanner at its installation site. The outer dimensions and the spaces required for installing the respective scanner types are as follows: (Unit: mm/inches) ADF type Flatbed type 640 (25.1) 390 (15.3) 300 (11.8) 342 700 500 (13.4) (19.6) (27.5) 432 (17.0) 686 329 690 (27.1) (27.0) (13.0) 1179 1030 (40.5) (46.4) Outer dimensions Installation space 2 Unlock the Transport Lock (Flatbed type only). Using a coin
Summary of the content on the page No. 13
2 Installing the Scanner 3) Gently close the Document Cover. 4) Change the position of the ADF. Be careful not to pinch your fingers when moving the ADF. Never rotate the ADF by more than 180 degree. Doing so may damage the ADF. The ADF can be set to any of the following three positions: After repositioning the ADF, be sure that the ADF is firmly locked to the new position. ■ Traditional (Factory default) ■ Standard (Space-saving type and for right-handed operators) Slide the ADF toward the
Summary of the content on the page No. 14
3 Connecting the Cables The following describes how to connect the cables between the scanner and your computer. The type of the connector for the cable depends on the scanner model you use. Confirm the scanner model and use the correct cable. ADF type fi-6670 3 USB or SCSI connection fi-6670A 2 USB or SCSI connection (when Kofax VRS is used) 5 SCSI ID SCSI cable 1 USB cable 4 Flatbed type fi-6770 3 USB or SCSI connection fi-6770A USB or SCSI connection (when Kofax VRS is used) fi-6750
Summary of the content on the page No. 15
3 Connecting the Cables 1 Make sure that the computer is turned OFF. 2 Open the Cable Cover (ADF type only). 3 Connect the scanner to your computer either with a USB or SCSI cable. You cannot make both USB and SCSI cable connections at the same time. You cannot connect multiple computers to the scanner at the same time. If Kofax VRS is not used on the fi-6670A or fi-6770A, connect the cable to USB Connector 1 or SCSI Connector 1 on the scanner. Turn off the scanner and your computer firs
Summary of the content on the page No. 16
4 Installing the Scanner Software Brief Information on the Bundled Software To scan documents with this scanner, you must install a scanner driver for operating the scanner as well as scanning software (hereinafter called the "application") for launching the driver and performing a scan. The scanner drivers and applications provided with the scanner are as follows: ■FUJITSU TWAIN 32 [TWAIN Driver] (*1) Conforms to the TWAIN standard. Used when you operate the scanner using TWAIN-compliant app
Summary of the content on the page No. 17
4 Installing the Scanner Software ■Adobe Acrobat 8.1 Standard A de-facto standard application used for creating, editing, managing, and making use of digitalized documents in PDF format. *1: The product ID used for its installation differs from the official product name. It is shown in [ ]. The software programs and their supported OSs are as follows: Windows 2000 Windows XP Windows XP Windows Server Windows Professional Home Edition Professional 2003 Vista (32-bit) (32/64-bit) (32/64-bit) (32
Summary of the content on the page No. 18
Installing the Bundled Software The following describes how to install the bundled software from the “SETUP DVD-ROM” contained in the scanner package. You can select either the [INSTALL (Recommended)] or [INSTALL (Custom)] menu when installing the SETUP DVD-ROM. The former installs all the software programs needed to operate the scanner; the latter installs the selected software programs one by one. For how to install Adobe Acrobat, refer to "Installing Adobe Acrobat" (on page 21) in the
Summary of the content on the page No. 19
4 Installing the Scanner Software 4 Click the [INSTALL (Recommended)] button. The list of scanners appears. 5 Select the scanner model name you will be using. Then, click the [Next] button. 6 Install the software, following the on-screen instructions. INSTALL (Custom) This menu lets you select and install the required software programs one by one. The procedure for custom-installing the required software is as follows: If an old version of the software is installed already, uninstall it first
Summary of the content on the page No. 20
3 Insert the SETUP DVD-ROM into your DVD drive. The [FUJITSU Image Scanner Setup] screen appears. If this screen does not appear, find "Install.exe" in the DVD-ROM using "Windows Explorer" or "Computer" and execute it directly. 4 Click the [INSTALL (Custom)] button. The [INSTALL PRODUCTS] screen appears. 5 Click the button for the software to be installed. 6 Install the software, following the on-screen instructions. Repeat Steps 5 and 6 to install other software program(s) here. For how to i
