Summary of the content on the page No. 1
MODEL H8211
14 PIECE DIE GRINDER KIT
INSTRUCTION MANUAL
COPYRIGHT © AUGUST, 2007 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#JM9807 PRINTED IN CHINA
Summary of the content on the page No. 2
����������������������������������������������������������������������� �������������������������������������������������������������� ���������������������������������������������������������������������� �������������������������������������������������������������������� ������������������������ ������������������������������������������������������������������ �������������������������������������������������������������������� ���������������������������������������������������������������
Summary of the content on the page No. 3
SAFETY For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures. Indica
Summary of the content on the page No. 4
7. AVOID ENTANGLEMENTS. Do not 16. DO NOT FORCE TOOL. It will do wear loose clothing, gloves, neck- the job better and safer at the rate ties, rings, bracelets, or other jewel- for which it was designed. ry, which may get caught in moving 17. CHECK FOR DAMAGED PARTS parts, when operating this tool. Wear BEFORE USING. Check for bind- a protective hair covering to contain ing and alignment of parts, broken long hair. parts, part mounting, loose bolts, 8. USE CORRECT AIR PRESSURE. and any oth
Summary of the content on the page No. 5
INTRODUCTION Foreword Specifications 1 1 The specifications, details, and photo- Collet Size.................................. ⁄8" and ⁄4" graphs in this manual represent the Model No Load Speed.......................22,000 RPM H8211 as supplied when the manual was Air Consumption...............................4 CFM 1 prepared. However, owing to Grizzly’s pol- Air Inlet..................................................... ⁄4" icy of continuous improvement, changes Required PSI...................
Summary of the content on the page No. 6
OPERATIONS To install a bit: 1. DISCONNECT THE GRINDER FROM THE AIR SUPPLY! 2. Use the two included wrenches to loos- en the collet nut, as shown in Figure 2. Note: It is not necessary to com- pletely remove the collet nut from the Read the manual before operation. shaft unless you are also changing the Become familiar with this tool, its collet. safety instructions, and its operation before beginning any work. Serious Collet Nut personal injury may result if safety or operational
Summary of the content on the page No. 7
The Model H8211 Grinder kit is equipped 1 1 with /4" and /8" collets for the included grinding stones. LUNG/EAR INJURY HAZARD! To change a collet: Wear protective equipment when 1. DISCONNECT THE GRINDER FROM using this tool. THE AIR SUPPLY. ACCIDENTAL START HAZARD! 2. Remove the collect nut from the grind- Disconnect before er. service or tool changes. 3. Using needlenose pliers, remove the AIR PRESSURE collet from the shaft. HAZARD! Never exceed max 4. Insert the desired collet and
Summary of the content on the page No. 8
H8211 PARTS LIST �� �� � �� � �� �� � � �� � �� �� �� � �� �� �� �� � �� � �� �� �� � �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� REF PART # DESCRIPTION REF PART # DESCRIPTION 1 PH8211001 HOUSING 25 PH8211025 SPECIAL WASHER 2 PH8211002 VALVE BUSHING 26 PH8211026 FRONT PLATE 3 PH8211003 TRIGGER 27 PH8211027 STEEL PIN 2 X 6 4 PH8211004 TRIGGER THROTTLE 28 P6000 BALL BEARING 6000ZZ 5 PH8211005 TORSION SPRING 29 PH8211029 CHUCK SEAT 6 PH8211006 ROLL PIN 1.5 X 20 30 PH8211030 LO
