Summary of the content on the page No. 1
Angle Grinder
100 mm (4”)
MODEL 9526PBH
115 mm (4-1/2”)
MODEL 9527PB
125 mm (5”)
MODEL 9528PB
DOUBLE
INSULATION
INSTR U CTION MANU AL
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
Summary of the content on the page No. 2
SPECIFICATIONS Model 9526PBH 9527PB 9528PB No load speed (RPM) 10,000/min 11,000/min 11,000/min Overall length 275 mm (10-7/8”) 275 mm (10-7/8”) 275 mm (10-7/8”) Net weight 1.5 kg (3.3 lbs) 1.5 kg (3.3 lbs) 1.5 kg (3.3 lbs) Spindle thread M10 x 1.25 5/8” 5/8” • Manufacturer reserves the right to change specifications without notice. Specifications may differ from country to country. GENERAL SAFETY RULES USA002-2 (For All Tools) WARNING: Read and understand all instructions. Failure to follow a
Summary of the content on the page No. 3
5. Avoid body contact with grounded sur- be used for appropriate conditions. Ordinary faces such as pipes, radiators, ranges and eye or sun glasses are NOT eye protection. refrigerators. There is an increased risk of Tool Use and Care electric shock if your body is grounded. 15. Use clamps or other practical way to 6. Do not expose power tools to rain or wet secure and support the workpiece to a conditions. Water entering a power tool will stable platform. Holding the work by hand or increase th
Summary of the content on the page No. 4
24. When servicing a tool, use only identical Use of unauthorized parts or failure to follow replacement parts. Follow instructions in Maintenance instructions may create a risk of the Maintenance section of this manual. electric shock or injury. USE PROPER EXTENSION CORD: Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in l
Summary of the content on the page No. 5
8. Be careful not to damage the spindle, the poor installation or a poorly balanced flange (especially the installing surface) wheel. or the lock nut. Damage to these parts 15. Use the specified surface of the wheel to could result in wheel breakage. perform the grinding. 9. NEVER use tool with wood cutting blades 16. Watch out for flying sparks. Hold the tool or other sawblades. Such blades when so that sparks fly away from you and other used on a grinder frequently kick and persons or flammabl
Summary of the content on the page No. 6
FUNCTIONAL CAUTION: DESCRIPTION • Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. 001021 Shaft lock CAUTION: 1 • Never actuate the shaft lock when the spindle is moving. The tool may be damaged. Press the shaft lock to prevent spindle rotation when install- ing or removing accessories. 1. Shaft lock 001034 Switch action CAUTION: • Before plugging in the tool, always check to see that the switch trigger actuates properly and returns t
Summary of the content on the page No. 7
001051 Installing side grip (handle) CAUTION: • Always be sure that the side grip is installed securely before operation. Screw the side grip securely on the position of the tool as shown in the figure. 001656 Installing or removing wheel guard 9526PBH 1 CAUTION: 2 • When using a depressed center grinding wheel/Multi- 3 disc, flex wheel, wire wheel brush or cut-off wheel, the wheel guard must be fitted on the tool so that the closed side of the guard always points toward the operator. Mount the
Summary of the content on the page No. 8
001083 To tighten the lock nut, press the shaft lock firmly so that the spindle cannot revolve, then use the lock nut wrench and 1 securely tighten clockwise. To remove the wheel, follow the installation procedure in reverse. 2 1. Lock nut wrench 2. Shaft lock 001095 Installing or removing flex wheel 1 (optional accessory) 2 3 WARNING: 4 • Always use supplied guard when flex wheel is on tool. Wheel can shatter during use and guard helps to reduce chances of personal injury. Follow instructions
Summary of the content on the page No. 9
• NEVER bang or hit grinding disc or wheel onto work. • Avoid bouncing and snagging the wheel, especially when working corners, sharp edges etc. This can cause loss of control and kickback. • NEVER use tool with wood cutting blades and other sawblades. Such blades when used on a grinder frequently kick and cause loss of control leading to personal injury. CAUTION: • After operation, always switch off the tool and wait until the wheel has come to a complete stop before putting the tool down. 0011
Summary of the content on the page No. 10
001228 Operation with wire wheel brush (optional accessory) 1 CAUTION: • Check operation of wire wheel brush by running tool with no load, insuring that no one is in front of or in line with the wire wheel brush. • Do not use wire wheel brush that is damaged, or which 1. Wire wheel brush is out of balance. Use of damaged wire wheel brush could increase potential for injury from contact with broken wires. • ALWAYS use guard with wire wheel brushes, assuring diameter of wheel fits inside guard. W
Summary of the content on the page No. 11
MAINTENANCE CAUTION: 001161 • Always be sure that the tool is switched off and unplugged before attempting to perform inspection or 1 maintenance. The tool and its air vents have to be kept clean. Regularly clean the tool’s air vents or whenever the vents start to 2 become obstructed. 1. Exhaust vent 2. Inhalation vent 001145 Replacing carbon brushes Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark. Keep the carbon brushes clean and free to slip in the
Summary of the content on the page No. 12
from your Makita distributor or factory service center, be sure to obtain and use all necessary fasteners and guards as recommended in this manual. Your failure to do so could result in personal injury to you and others. If you need any assistance for more details regarding these accessories, ask your local Makita service center. 001179 1 222 8 12 13 3 3 9 11 3 4 6 10 14 5 7 5 5 9526PBH 9527PB 9528PB 1 Grip 36 2 Wheel guard 3 Inner flange 35 Inner flange 45 Inner flange 45 4 Depressed center gri
Summary of the content on the page No. 13
Memo 13
Summary of the content on the page No. 14
Memo 14
Summary of the content on the page No. 15
Memo 15
Summary of the content on the page No. 16
MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centres. If inspection shows the trouble is caused by defective workmanship or material, M
