Summary of the content on the page No. 1
Angle Grinder
180 mm (7”) MODEL 90471.
230 mm (9”) MODEL 9049
INSTRUCTION MANUAL
DOUBLE
INSULATION
No load speed
Overall length
Net weight Spindle thread
(RPM)
6,000 I 470 mm (18-112“) I 4.8 kg (10.6 Ibs) I 5/8”-11 UNC
* Manufacturer reserves the right to change specifications without notice.
* Note: Specifications may differ from country to country.
WARNING: For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
Summary of the content on the page No. 2
GENERAL SAFETY RULES (For All Tools) WARNING! Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS READ ALL INSTRUCTIONS. 1. Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. 2. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which
Summary of the content on the page No. 3
11. Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with your finger on the switch or plugging in tools that have the switch on invites accidents. 12. Remove adjusting keys or switches before turning the tool on. A wrench or a key that is left attached to a rotating part of the tool may result in personal injury. 13. Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the tool in unexpecte
Summary of the content on the page No. 4
Specific Safety Rules 1. Always use proper guard with grinding wheel. A guard protects operator from broken wheel fragments. 2. Accessories must be rated for at last the speed recommended on the tool warning label. Wheels and other accessories running over rated speed can fly apart and cause injury. 3. Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a "live" wire will make exposed metal p
Summary of the content on the page No. 5
SYMBOLS The followings show the symbols used for tool. ........................... volts ................................. amperes ................................. herts ................................. kilograms ...... . . hours ................................. minutes ....... seconds ........................... alternating current ................... direct current ................. no load speed alternating or direct current ................................. Class II Construct
Summary of the content on the page No. 6
Installing wheel guard When using a depressed center wheel or an abrasive cut-off wheel, always use a wheel guard. Mount the wheel guard with the tab r------ ,-Wheel guard on the wheel guard band aligned with the notch on the bearing box Then rotate the wheel guard 160 degrees counterclockwise. Be sure to tighten the screw securely. Installing side grip (auxiliary handle) Always install the side grip on the tool securely before operation. The side grip can be installed in any of thre
Summary of the content on the page No. 7
Installing or removing depressed center wheel CAUTION: Always be sure that the tool is switched off and unplugged before installing or removing the wheel. Mount the inner flange onto the spindle. Fit the wheel on over the inner flange and screw the lock nut onto the spindle. To tighten the lock nut, press the shaft lock firmly so that the spindle cannot revolve, Lock nut wrench- then use the lock nut wrench and securely tighten clockwise. To remove the wheel, follow the installation
Summary of the content on the page No. 8
Operation Hold the tool firmly. Turn the tool on and then apply the wheel or disc to the workpiece. In general, keep the edge of the wheel or disc at an angle of about 15O to the workpiece surface. During the break-in period with a new wheel, do not work the grinder in the B direction or it will cut into the workpiece. Once the edge of the wheel has been rounded off by use, the wheel may be worked in both A and B directions. I WARN I NG : It should never be necessary to force the t
Summary of the content on the page No. 9
MAINTENANCE CAUTl ON: Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Replacing carbon brushes When the resin insulating tip inside the carbon brush is exposed to contact the Insulating tip commutator, it will automatically shut off the 7r motor. When this occurs, both carbon brushes should be replaced at the same time. Commutator Use only identical carbon brushes. -Carbon brush 1 Use a screwdriver to remove the b
Summary of the content on the page No. 10
ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. @Depressed center wheel (1 Per pkg) @Wheel guard Grit Size (mm) For Model Part No. For Model Part No. 165191-5 9047L 741425-6 24 ,7,!:qr; i 9047L 164879-4 I 9049 I 24 I ,,,?~~r46~ I 904
Summary of the content on the page No. 11
@Abrasive disc 15 per pkgl @Rubber pad Part No. 743012-7 @Sanding lock nut 48 Part No. I Grit I Diameter h" (For abrasive disc) 742067-A-5 I 16 1 Part No. 22451 7-1 742069-A-5 I 24 I 742089-A-5 180 (7") 742070-A-5 742071 -A-5 80 742091-A-5 I 120 I @Wire cup brush @Flexible grinding wheel (10 per pkg) Part No. I Diameter lmml Part No. I Grit I Size lmml I Far Model 743206-A 150 (6") 743206-E 3 x 22 18Ox 17" x 118" x 718") 741442-6 I 60 I 9047L lincludes one back up pad, @
Summary of the content on the page No. 12
No".-01 -'96 US ANGLE GRINDER 180 mm (7") Model 9047L 230 mm (9") Model 9049 Note: The switch and other part configurations may differ from country to country. 12
Summary of the content on the page No. 13
MODEL 9047L, 9049 Nov.-01-'96 US IFOM DESCRIPTION '2: DESCRIPTION - MACHINE MACHINE 25 1 Retaining Ring R-40 1 1 FIELD ASSEMBLY 1 Ball Bearing 62030DW 2 1 Baffle Plate 26 27 1 Bearing Box 3 1 Ball Bearing 6200DDW Insulation Washer 28 1 Spindle 4 1 29 1 Pan Head Screw M8x25 5 1 ARMATURE ASSEMBLY 1 Wheel Cover IWith Item 3. 4 & 61 30 31 1 Inner Flange 89 6 1 Fan 80 60 32 1 Lock Nut 5/6-40 7 1 Bearing Retainer 33 4 Tapping Screw CT 5x16 8 1 Ball Bearing 63OlDDW 34 1 Makila Mar
Summary of the content on the page No. 14
MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE to one of Makita’s Factory or Authorized Service Centers. If inspection shows tool, freight prepaid, the trouble is caused by defective workmanship or mate
