Summary of the content on the page No. 1
OPERATOR’S MANUAL
GASOLINE PRESSURE WASHER
3000 PSI
RY80030
Your pressure washer has been engineered and manufactured to Ryobi’s high standard for dependability, ease of operation,
and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.
DANGER: You WILL be KILLED or SERIOUSLY HURT if you do not follow the instructions in this operator’s
manual.
Thank you for buying a Ryobi product.
SAVE THIS MANUAL FOR FUTURE REFERENCE
Summary of the content on the page No. 2
TABLE OF CONTENTS n Introduction .......................................................................................................................................................................2 �n Important Safety Instructions ............................................................................................................................................3 �n Specific Safety Rules ..................................................................................................
Summary of the content on the page No. 3
IMPORTANT SAFETY INSTRUCTIONS n NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped. WARNING: n CHECK DAMAGED PARTS. Before further use of the Read and understand all instructions. Failure to follow tool, a guard or other part that is damaged should all instructions listed below may result in electric shock, be carefully checked to determine that it will operate fire and/or carbon monoxide poisoning which will cause properly and perform its intended function. Check for
Summary of the content on the page No. 4
SPECIFIC SAFETY RULES n NEVER DIRECT A WATER STREAM TOWARDS n ALWAYS REFUEL OUTDOORS. Never refuel indoors or PEOPLE OR PETS, OR ANY ELECTRICAL in a poorly ventilated area. DEVICE. n NEVER STORE THE MACHINE WITH FUEL IN THE n BEFORE STARTING ANY CLEANING OPERATION, FUEL TANK INSIDE A BUILDING where ignition sources close doors and windows. Clear the area to be cleaned are present, such as hot water and space heaters, clothes of debris, toys, outdoor furniture, or other objects that dryers
Summary of the content on the page No. 5
SYMBOLS Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpreta- tion of these symbols will allow you to operate the tool better and safer. SYMBOL NAME DESIGNATION/EXPLANATION Wet Conditions Alert Do not expose to rain or use in damp locations. To reduce the risk of injury, user must read and understand Read The Operator’s Manual operator’s manual before using this product. Always wear safety goggles, safety glasses with side shields,
Summary of the content on the page No. 6
SYMBOLS The following signal words and meanings are intended to explain the levels of risk associated with this product. SYMBOL SIGNAL MEANING DANGER: Indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury. WARNING: Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury. CAUTION: Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury.
Summary of the content on the page No. 7
FEATURES PRODUCT SPECIFICATIONS Engine Size...................................................................................................................................................................211 cc Engine Output, Horsepower............................................................................................................................................7 HP Fuel Tank Capacity...................................................................................................
Summary of the content on the page No. 8
FEATURES KNOW YOUR PRESSURE WASHER RECOIL STARTER See Figure 1. The recoil starter is used (along with the on/off switch) to Before attempting to use this product, familiarize yourself start the power washer. with all operating features and safety rules. SPRAY WAND ACCESSORIES STORAGE The spray wand has a round assist handle that provides added control of the spray wand and helps reduce fatigue. Safely stores accessories (not included) within easy reach. STORAGE BRACKET DETERGENT BUCKET Once
Summary of the content on the page No. 9
ASSEMBLY UNPACKING WARNING: This product requires assembly. Do not attempt to modify this tool or create accesso- n Carefully cut the box down the sides then remove the ries not recommended for use with this tool. Any such tool and any accessories from the box. Make sure that alteration or modification is misuse and could result in a all items listed in the packing list are included. hazardous condition leading to possible serious personal NOTE: This tool is heavy. To avoid back injury,
Summary of the content on the page No. 10
ASSEMBLY ATTACHING THE RESTING FOOT See Figure 3. To attach the resting foot to the pressure washer: n Lift the machine slightly. Slide the resting foot into the bottom of the spray wand storage tube. n Push the resting foot into the storage tube until the base RESTING of the machine rests in the grooves on top of the resting FOOT foot. ASSEMBLING THE SPRAY WAND See Figure 4. Fig. 3 To attach the assist handle assembly: n Remove the wing screw from the assist handle assembly then slide the
Summary of the content on the page No. 11
ASSEMBLY ADDING OIL TO THE ENGINE See Figure 7. NOTE: This machine has been shipped with approximately SLOT 2 oz. of oil in the enginge from testing. You must add oil to CLEAR the engine before starting it the first time. INJECTION HOSE CAUTION: Any attempt to start the engine without adding oil will result in engine failure. n Place pressure washer on a flat, level surface. n Unscrew the oil cap / dipstick by turning counterclock- BARBED FITTING wise. n Using 4-stroke engine oil (10W-30)
Summary of the content on the page No. 12
ASSEMBLY CONNECTING THE HIGH PRESSURE HOSE TO THE PUMP HIGH PRESSURE See Figure 9. HOSE ������After the high pressure hose has been uncoiled and attached to the spray wand: n Pull back and hold the spring loaded collar on the pump. n Insert the nozzle on the end of the high pressure hose into the collar. n Release the collar. n Pull on the hose to be certain it is properly secured. CONNECTING THE GARDEN HOSE TO THE PRESSURE WASHER See Figure 10. SPRING LOADED Water supply must come from a
Summary of the content on the page No. 13
OPERATION APPLICATIONS OFF This product has been designed for the purposes listed POSITION ON/OFF below: SWITCH n �Removing dirt and mold from decks, cement patios, and house siding n �Cleaning cars, boats, motorcycles, and grills STARTING/STOPPING THE PRESSURE CHOKE WASHER (CLOSED) See Figures 11 - 13. CAUTION: Do not run the pump without the water supply connected and turned on. Before starting the engine, connect all hoses and check all fluids (oil and gas). Turn the garden hose on the
Summary of the content on the page No. 14
OPERATION To stop the engine using the fuel valve: To engage the lock out: n Close the fuel valve and wait for the engine to stop. n Push up on the lock out until it clicks into the slot. NOTE: Avoid letting fuel remain in the carburetor for long To disengage the lock out: periods as this can clog carburetor passages with impuri- n Push the lock out down and into its original position. ties resulting in malfunctions. For the most effective cleaning, the spray nozzle should be between 8 in. and
Summary of the content on the page No. 15
OPERATION MOVING THE PRESSURE WASHER TO MOVE THE MACHINE See Figure 17. n Loosen the pivot knob located halfway down the spray wand storage pipe. n Grasp the handle at the rear of the pressure washer. Turn the top section of the pressure washer until it is fully ex- tended as shown in figure 17. Retighten the pivot knob. n Grasp the moving handle and lift the machine off the resting foot. Roll the machine to the desired position. STORING THE PRESSURE WASHER See Figure 17. �����Allow 30 minute
Summary of the content on the page No. 16
MAINTENANCE air filter after each refueling. For best performance, replace the air filter at least once a year. WARNING: To clean the air filter: When servicing, use only identical Ryobi replacement n Remove the cover. parts. Use of any other parts may create a hazard or cause product damage. AIR FILTER COVER WARNING: Always wear safety goggles or safety glasses with side shields during power tool operation or when blowing AIR FILTER dust. If operation is dusty, also wear a dust mask. WIRE
Summary of the content on the page No. 17
MAINTENANCE CHANGING THE OIL See Figure 20. n Shut off the engine. n �Place a container under the pressure washer. n Remove the oil plug and drain the old oil. NOTE: Drain the oil while the engine is still warm but not 0.6 - 0.7mm hot. Warm oil will drain quickly and more completely. n Replace the oil plug. Fig. 21 n Replace the oil with new, clean oil. This engine will hold 20 oz. or .6 liters of oil. CHECKING A FOULED SPARK PLUG See Figure 21. n Clean off carbon deposits on the spark plug
Summary of the content on the page No. 18
MAINTENANCE n Inspect the spark plug and clean or replace, as neces- STORING THE PRESSURE WASHER sary. It is important to store this product in a frost-free area. Always n Reinstall the spark plug, but leave the spark plug wire empty water from all hoses, the pump, the fuel tank, and the disconnected. detergent bucket before storing. Air Filter: NOTE: Use of a fuel stabilizer and pump saver will give you better performance and increase the life of the machine. n Clean the air filter. Disch
Summary of the content on the page No. 19
TROUBLESHOOTING PROBLEM CAUSE SOLUTION Engine fails to start 1. Engine switch is in the off position 1. Move switch to start. 2. No fuel in tank 2. Fill tank. 3. Spark plug shorted or fouled 3. Repl
Summary of the content on the page No. 20
NOTES 20
