Summary of the content on the page No. 1
High Pressure Washer
Operator Manual
Overview .......................................... 2
Precautions ................................ 3 - 4
Assembly Instructions ..................... 4
Operating Instructions..................... 5
Using the accessories ..................... 6
Working with Detergents................. 7
Shut Down and Clean-Up ............... 8
Taking a Break ................................ 8
Winterizing and Long-Term
Storage ....................................... 8 - 9
Cleani
Summary of the content on the page No. 2
OVERVIEW For household use only! 2 1. Power cord 7. Accessory compartment 2. Trigger gun 8a. Detergent tank 1 3. Trigger gun safety lock 8b. Detergent tank 2 4. High pressure hose 9. High pressure outlet 5. Water inlet with filter 10. On/Off switch 6. Transport handle 11. Quattro nozzle 12. Washing brush THE BEST ANTI-FREEZE PROTECTION IS PROVIDED BY USING AND STORING THE MACHINE IN SHELTERED SPACE
Summary of the content on the page No. 3
IMPORTANT PRECAUTIONS – Read First! Safety Warnings Extension Cords When using this product basic precautions Use a sufficient gauge: should always be followed: Up to 25 ft. = 12/3 AWG. • Read all the instructions before using the 25 to 50 ft. =10/3 AWG. product. Use only extension cords that are intended High pressure jets can be dangerous if for outdoor use. These extension cords are subject to misuse. The jet must not be identified by a marking “Acceptable for use directed at persons, anima
Summary of the content on the page No. 4
IMPORTANT PRECAUTIONS – continued Water Supply (Cold Water Only) Never use the pressure washer to draw in water contaminated with solvents, e.g. Water hose must be at least 1/2 inch or paint thinner, gasoline, oil, etc. 5/8 inch in diameter. NOTE: Dirt in the feed water will Flow rate of water supply must not fall damage the unit. To avoid this risk, below 2 GPM (gallons per minute). we recommend fitting a water filter. Flow rate can be determined by running the Always prevent deb
Summary of the content on the page No. 5
OPERATING INSTRUCTIONS 2. 1. Step 2 Insert the quattro nozzle to the trigger gun. Press in against the spring tension and twist into the locked position. Step 1 Connect the high pressure hose to the high pressure outlet. 5 Step 4 Step 3 Connect garden hose to the cold water Connect the garden hose to the water inlet. source and turn water on completely. Plug the power cord into the power outlet. //O ON N //O ON N Step 5 Step 6 Unlock the lock of the trigger gun (A). Turn on the pressure washer
Summary of the content on the page No. 6
USING THE ACCESSORIES Quattro Nozzle Selecting the jet Release the trigger of the handgun. Rotate the nozzle head until the symbol is aligned with the marking on the spray lance. Note: The marking on the spray lance must be up during operation. High pressure High pressure Rotating jet for Low pressure pencil jet fan jet maximum dirt fan jet for cleaning cleaning cutting action detergent 6 injection Wash brush This brush is ideal for removing stubborn Warning dirt and stains from finished surface
Summary of the content on the page No. 7
WORKING WITH DETERGENTS a) b) Step 1 Step 2 Install the Wash brush or Quattro nozzle. a) Fill the Detergent Tanks (No.8a,No.8b) Turn Quattro Nozzle to Low pressure with the selected detergent, ensuring it is position. Rotate the spray lance in the the correct concentration (read recom- direction of “ ” until reaching the stop. mended dosage on label) or b) Fill the Detergent Tank with Ready To Note: No detergent in high-pressure mode Use detergent. 7 Step 3 Step 4 Adjusting the detergent dosing
Summary of the content on the page No. 8
SHUTTING DOWN & CLEAN-UP OFF OFF / / Step 1 Step 2 Step 3 Turn the switch to off (O) Turn off the water source. Press trigger to release position and unplug cord from water pressure. outlet. A B 8 Step 4 Step 6 Step 5 Disconnect the garden hose from Pull trigger down Disconnect the high pressure hose the water inlet on the unit. (A) and engage from the high pressure outlet. gun safety lock (B). TAKING A BREAK... five minutes or more A OFF OFF / / Step 1 Step 2 Pull trigger down (A) Turn pressure
Summary of the content on the page No. 9
WINTERIZING AND LONG-TERM STORAGE – continued 5) Cleaning the 6) Cleaning the water inlet filter detergent inlet filter Pull out the water in- Pull it out and rinse out let filter with flat-nose in warm water. pliers and rinse out in warm water. Maintenance The unit is maintenance- free. CLEANING TIPS Cement Patios, Brick and Deck Cleaning (with or without detergent) Stone Pre-rinse deck and surrounding area with (with or without detergent) fresh water. If using Kärcher Deck + Fence Pre-rinse cl
Summary of the content on the page No. 10
CLEANING TIPS – continued apply to surface at low pressure. Allow Barbecue Grills, Outdoor Pressure Wash to remain on surface 1-3 Power Equipment & Gardening minutes. Do not allow detergent to dry on Tools surface. If needed use special Wash Brush (with or without detergent) Attachment (not included) to remove Pre-rinse cleaning surface with fresh water. stubborn dirt. Rinse at high pressure in a If using Kärcher Pressure Wash or sweeping motion keeping the spray nozzle Degreaser, apply deterge
Summary of the content on the page No. 11
TROUBLESHOOTING Disconnect the machine from the power source before making any repair. Symptom Cause Solution Motor will not start. On/Off switch is in the “OFF” (O) Turn switch to the “ON” (I) position position. Power cord is not plugged in. Plug in power cord. Extension cord is too long. Replace extension cord with either Extension cord is not proper gauge. a 25 ft. 12/3 gauge cord or a 50 Extension cord is damaged. ft. 10/3 gauge cord. Electrical outlet does not supply Try a different outlet.
Summary of the content on the page No. 12
TROUBLESHOOTING – continued Symptom Symptom Symptom Symptom Symptom Cause Solution No detergent. No detergent. No detergent. No detergent. No detergent. Detergent is too thick. Dilute detergent. Spray wand is in high pressure Turn spray wand tip to low position. pressure position. Discharge nozzle is obstructed. Blow out or remove debris with a fine needle. Spray wand leaks. Spray wand leaks. Spray wand leaks. Spray wand leaks. Spray wand leaks. Spray wand not properly attached. Insert the spray
