Summary of the content on the page No. 1
6500 Slide RM-240
Service Manual Level &2
SERVICE MANUAL
Level &2
RM-240
Transceiver characteristics:
Band:
EGSM: Quad-band 850/900/1800/1900MHz
WCDMA: 850/2100MHz
Display:
LCD: 5.588cm QVGA (2.2”) (320x240 pixel); 16M colors
Camer a:
Camera: 3.2 Megapixel, 8x digital zoom, autofocus, flash
Operating System:
Series 40
Connections:
Wireless: Bluetooth
Connector: Micro USB Connector; AV Connector
Memory:
MicroSD™ (max 4GB)
Transceiver with BP-5M Li-Ion battery pack
Talk ti
Summary of the content on the page No. 2
6500 Slide RM-240 Service Manual Level &2 TABLE OF CONTENTS Page . CHANGE HISTORY 3 2. COPYRIGHT 3 3. WARNINGS AND CAUTIONS 4 4. ESD PROTECTION 4 5. CARE AND MAINTENANCE 5 6. BATTERY INFORMATION 5 7. EXPLODED VIEW 6 8. LEVEL 2 SOLDER COMPONENTS 7 9. SERVICE TOOLS 8 0. SW-UPDATE 9 . DISASSEMBLY 0 2. ASSEMBLY 8 Page 2 (25) ISSUE CONFIDENTIAL Copyright © 2007 NOKIA. All rights reserved.
Summary of the content on the page No. 3
6500 Slide RM-240 Service Manual Level &2 . CHANGE HISTORY Status Version No. Date Comments Draft 0.1 07.Sep.2007 Initial draft Approved 1.0 19.Sep.2007 First arroved release The purpose of this document is to help NOKIA service levels 1 and 2 workshop technicians to carry out service to NOKIA products. This Service Manual is to be used only by authorized NOKIA service suppliers, and the content of it is confidential. Please note that NOKIA provides also other guidance documents (e.g. Servi
Summary of the content on the page No. 4
6500 Slide RM-240 Service Manual Level &2 3. WARNINGS AND CAUTIONS Warnings and Cautions Please refer to the phone’s user guide for instructions relating to operation, care and maintenance including impor- tant safety information. Note also the following: Warnings: 1. CARE MUST BE TAKEN ON INSTALLATION IN VEHICLES FITTED WITH ELECTRONIC ENGINE MANAGEMENT SYSTEMS AND ANTI–SKID BRAKING SYSTEMS. UNDER CERTAIN FAULT CONDITIONS, EMITTED RF ENERGY CAN AFFECT THEIR OPERATION. IF NECESSARY, CONSULT
Summary of the content on the page No. 5
6500 Slide RM-240 Service Manual Level &2 5. CARE AND MAINTENANCE This product is of superior design and craftsmanship and should be treated with care. The suggestions below will help you to fulfil any warranty obligations and to enjoy this product for many years. • Keep the phone and all its parts and accessories out of the reach of small children. • Keep the phone dry. Precipitation, humidity and all types of liquids or moisture can contain minerals that will corrode electronic circuits. • D
Summary of the content on the page No. 6
6500 Slide RM-240 Service Manual Level &2 7. EXPLODED VIEW See corresponding ITEM/CIRCUIT REF in the Spare Parts Service Bulletins on NOL. Page 6 (25) ISSUE CONFIDENTIAL Copyright © 2007 NOKIA. All rights reserved.
Summary of the content on the page No. 7
6500 Slide RM-240 Service Manual Level &2 8. LEVEL 2 SOLDER COMPONENTS Page 7 (25) ISSUE CONFIDENTIAL Copyright © 2007 NOKIA. All rights reserved.
Summary of the content on the page No. 8
6500 Slide RM-240 Service Manual Level &2 9. SERVICE TOOLS FLS-5 incl. ACF-8, Driver and User ACF-8 Travel Charger AC-4 Guide Universal Power Supply is used to Small and lightweight charger for Dongle and flash device incorporated power FLS-5. fast charging of your phone battery. into one package, developed specifi- cally for POS use. CA-0 RJ-80 Service Cable to connect the PC with Soldering Jig the Micro USB connector. Internal Battery BP-5M 0772040 Inserted under the back cover, this NM
Summary of the content on the page No. 9
6500 Slide RM-240 Service Manual Level &2 0. SW-UPDATE Flash Concept – (Point of Sales) To use FLS-5 Flash Dongle you have to follow the user guide inside the sales package. Please check always for the latest version of flash software, which is available on NOKIA Online. Page 9 (25) ISSUE CONFIDENTIAL Copyright © 2007 NOKIA. All rights reserved.
Summary of the content on the page No. 10
6500 Slide RM-240 Service Manual Level &2 . DISASSEMBLY 1. Nokia 6500 Slide disassembly. 2. You will need the Nokia Standard Toolkit version 2. 3. Unlock and remove the BATTERY COVER. 4. Equip your bitholder with the Torx Plus size 4 bit. 5. Unscrew these 4 screws in the order shown. 6. Discard these screws. Do not use them again. 7. Shift open the slider. Carefully insert the tips of the angled 8. Now swing up the tweezers in order to lever out the metal tweezers into the recess as shown.
Summary of the content on the page No. 11
6500 Slide RM-240 Service Manual Level &2 9. Repeat this procedure on the other side. 10. Gently press both edges together until a gap apears at the end of the KEYMAT. 11. Avoid press this key while pressing the edges. 12. Unlock the clips at the bottom side. 13. Insert the SS-93 at the shown position. 14. Carefully unlock this flex foil connector. 15. Lift up the BOTTOM KEYMAT SUPPORT. 16. Disconnect this flex foil connector. Page (25) ISSUE CONFIDENTIAL Copyright © 2007 NOKIA. All right
Summary of the content on the page No. 12
6500 Slide RM-240 Service Manual Level &2 17. Now these assemblies can be separated. 18.Insert the angled tweezers into the recess as shown. 19. Carefully shift the tip of the tweezers outside. 20. Repeat this procedure at the other side of the BOTTOM KEYMAT. 21. If both clips are released properly, the BOTTOM KEYMAT can 22. The removal of the KEYMAT is also possible without be lifted up. removing the bottom screws. 23. Carefully press at both edges,- like shown before. Lift out 24. Locate t
Summary of the content on the page No. 13
6500 Slide RM-240 Service Manual Level &2 25. Repeat this procedure on opposite side. 26. Now the BOTTOM KEYMAT can be removed. 27. Carefully lever up the edges of the BOTTOM FLEX... 28. ...on both sides. 29. Remove the BOTTOM FLEX. 30. Keep this adhesive clean if this part should be reused. Remove all adhesive residues from the SLIDE MODULE ASSY. 31. Unscrew these screws in the shown order. 32. Discard these screws. Do not use them again. Page 3 (25) ISSUE CONFIDENTIAL Copyright © 2007 N
Summary of the content on the page No. 14
6500 Slide RM-240 Service Manual Level &2 33.Shift open the slider in order to reach the next screws. 34. Unscrew these screws in the shown order. 35. Discard these screws. Do not use them again. 36. Slightly open the clips of the SLIDE MODULE ASSY. 37. Lift up the SLIDE MODULE ASSY. 38. Shift the slider into position shown to reach the maximum recess. Slot the connector through the slider. 39. Open the clips of the TOP KEYMAT SUPPORT... 40....on both sides. Page 4 (25) ISSUE CONFIDENTIAL
Summary of the content on the page No. 15
6500 Slide RM-240 Service Manual Level &2 41. Lift up the TOP KEYMAT SUPPORT. 42. The TOP KEYMAT ASSY can be removed now. 43. Carefully lift up the LCD AM 240x320 with the SS-93. Lift up 44. Be double carefull while lifting out the CMOS CAMERA the whole assembly. MODULE. 45. Ease out the EARPIECE from the shown side. 46. Discard this EARPIECE. Do not use it again. 47. Bend the top part of the cover. Twist out the glued in 48. These parts can be separated if necessary. EARPIECE HOUSING ASSEMBLY
Summary of the content on the page No. 16
6500 Slide RM-240 Service Manual Level &2 49. Gently open the flex connector. Avoid putting pressure to 50. Lift up the glued inTOP FLEX , beginning at the shown side... the components. 51....continue at the large connector. 52. If all adhesive parts are released, the Top FLEX ASSY can be removed easily. 53. Keep this adhesive clean if this part should be reused. 54. Open the flex connector of the CAMERA FLEX MODULE. Remove any adhesive residues on the opposing part. 55. Now the CAMERA FLEX
Summary of the content on the page No. 17
6500 Slide RM-240 Service Manual Level &2 57. Now lift up the ENGINE MODULE. 58. Never touch the microphone with a tool or with fingers. 59. Turn the D-COVER ASSEMBLY. Let drop out the ANTENNA/IHF 60. Lift up the DC PLUG. ASSEMBLY. 61. Lift out the FLASH ASSEMBLY. 62. Keep this adhesive clean if this part should be reused. The disassembly procedure is now complete. Page 7 (25) ISSUE CONFIDENTIAL Copyright © 2007 NOKIA. All rights reserved.
Summary of the content on the page No. 18
6500 Slide RM-240 Service Manual Level &2 2. ASSEMBLY 1. Nokia 6500 Slide assembly. 2. You will need the Nokia Standard Toolkit version 2. 3. Place the FLASH ASSEMBLY. Remove the protective film if this 4. Push it down slightly. part is new. 5. Insert the DC PLUG . 6. Insert the ANTENNA/IHF ASSEMBLY. 7. Insert the ENGINE MODULE, beginning from the bottom side. 8. Click the ENGINE MODULE into its place... Page 8 (25) ISSUE CONFIDENTIAL Copyright © 2007 NOKIA. All rights reserved.
Summary of the content on the page No. 19
6500 Slide RM-240 Service Manual Level &2 9...on both sides. Do not touch the components. Check that the 10. The CAMERA MODULE and the FLEX MODULE can be ordered Keys operate before continuing. as separate parts only.. 11. Insert the CAMERA MODULE into its housing. Push it into its 12. Check the camera window for cleaness. place slightly. Do not touch the lens. Insert the CAMERA FLEX MODULE into its compartment. 13. Close the flex connector of the camera. 14. Insert the EARPIECE HOUSING ASSE
Summary of the content on the page No. 20
6500 Slide RM-240 Service Manual Level &2 17. Insert the EARPIECE into its compartment. 18. Push it down carefully. Never push down the metal part, otherwise the EARPIECE could be destroyed. 19. Insert the TOP KEYMAT ASSY. 20. Place the LCD as shown. 21. Align it to the front guiding. 22. Place the TOP FLEX ASSEMBLY. Remove the protective film before if this part is new. 23. Slightly push the CMOS CAMERA into its compartment. 24. Mind the guiding pin of the TOP FLEX ASSEMBLY. Page 20 (25) ISS
