Summary of the content on the page No. 1
Module No. 2220
2220-1
12-hour/24-hour Timekeeping
GETTING ACQUAINTED
Pressing D while the day is flashing on the setting screen causes the
indicator for the current timekeeping format (12H or 24H) to flash on the
Congratulations upon your selection of the CASIO Wrist Camera (this watch).
display. Each press of E at this time toggles between 12-hour (12H) and
To get the most out of your purchase, be sure to read this manual carefully
24-hour (24H) timekeeping.
and keep the manual and everything
Summary of the content on the page No. 2
2220-2 GENERAL GUIDE Timekeeping Mode • Pressing B or E while in the Timekeeping Mode displays the Viewer Press D to change from mode to mode. Screen, which you can use to view images stored in watch memory. Press B or E. FRI 3‰ Timekeeping Mode IR Mode P 1‰:58 35 FRI 3‰ IR Press D. P COM 1‰:58 Press D to return from the Viewer Screen to the Timekeeping Mode. 35 • Each press of C while in the Timekeeping Mode toggles between the Day of the Week Screen and the Month Screen. Day o
Summary of the content on the page No. 3
2220-3 To select the recording mode Controlling the Camera Mode Image In the Camera Mode, press C to cycle through the available recording You can use the following procedures to adjust the brightness and to specify modes as shown below. the type of lighting present when recording an image. Normal Mode Merge Mode Art Mode Adjusting the Image Brightness The watch automatically sets the brightness of the image when you record it. You can also change the brightness level manually when you want to c
Summary of the content on the page No. 4
2220-4 4. Press F and a confirmation message Attaching Text to an Image appears on the display. You can use the following procedure to attach up to 24 characters of text for ALL 5. If you really want to delete all images in each image. memory, press E to move the pointer to NO YES and then press F. To clear the To attach text to an image YES confirmation message without deleting 1. In the VISUAL DATABANK Mode, use E anything, leave the pointer at NO and (+) and B (–) to display the image to
Summary of the content on the page No. 5
2220-5 3. While the hour setting is flashing, use E (+) and B (–) to change it. Using the Viewer Screen • Holding down either button changes the setting at high speed. The press of a button in the Timekeeping Mode displays the Viewer Screen, • When setting the alarm time using the 12-hour format, take care to set the which you can use to view images stored in memory. time correctly as am (A indicator) or pm (P indicator). 4. Press D so that the minute digits of the alarm time start to flash. Imp
Summary of the content on the page No. 6
2220-6 To send a single image STOPWATCH MODE 1. On the COM menu, press E to move the pointer to OTHERS. The Stopwatch Mode lets you measure Hours COM elapsed time, split times, and two finishes. The Minutes PC range of the stopwatch is 23 hours, 59 minutes, 59.99 seconds. OTHERS STW ‰H Pointer ‰‰ '‰‰ 2. Press F to display the OTHERS menu, 00 with the pointer located next to SEND. OTHERS 3. Press F again to display the image selection screen. SEND Seconds RECEIVE 1/100 second To m
Summary of the content on the page No. 7
2220-7 • Never leave a dead or weak battery in the battery compartment. Doing so Communication Errors runs the risk of damage and malfunction due to battery fluid leaks. • Be sure to dispose of old batteries according to the local laws and Watch Message/Indicator Cause and Remedy regulations in your area. OTHERS SEND • Communication failed for some reason. • Improperly replacing the battery can result in damage to the watch. ERROR Try again. Sender Repairing such damage will be charged to you, s
Summary of the content on the page No. 8
2220-8 Settings Following Battery Replacement The watch retains image data in memory when you replace the battery. However, the current time, date, alarm settings, and countdown start time are all cleared. Be sure you make these settings each time you replace the battery.
