Cisco Systems SPA 2100 user manual

Summary of the content on the page No. 1

Cisco SPA 2100 Phone Adapter Installation Manual

Installation of the Cisco SPA 2100 Phone Adapter to NationPhone
Index
P. 1 Index, before you begin, and what is included
P.2 Installing the NationPhone Router & Phone Adapter SPA2100
P.3 Installing the NationPhone Router & Phone Adapter on Multiple Computers
P.4 About the NationPhone Router & Phone Adapter
P.5 Troubleshooting
P.6 DSL/PPPoE Set Up ( most cases when you have internet through you telephone company)
P.9 Troubles

Summary of the content on the page No. 2

Installing the NationPhone Router & Phone Adapter SPA2100 1. Power off your DSL or cable modem and computer. 2. Insert an Ethernet cable into the WAN port. Connect the other end of an Ethernet cable into your DSL or cable modem. 3. Insert an end of another Ethernet cable into the LAN port. Connect the other end of the Ethernet cable into the Ethernet port on your computer. 4. Insert the line from your telephone handset into the PHONE 1 port of the NationPhone Router

Summary of the content on the page No. 3

Installing the NationPhone Router & Phone Adapter on Multiple Computers 1. Power of your DSL or cable modem, router, and any devices connected to the router. 2. Insert an Ethernet cable into the WAN port. Connect the other end of the Ethernet cable into your DSL or cable modem. 3. Insert an end of another Ethernet cable into the LAN port. Connect the other end of the Ethernet cable into the Ethernet port on your router. Connect your PC and all other network devi

Summary of the content on the page No. 4

About the NationPhone Router & Phone Adapter The NationPhone Router & Phone Adapter enables you to connect your phones and either one or more computers to your broadband network. When connecting to a single computer, you do not need a router. BEFORE PROCEEDING: If you are using DSL that requires PPPoE authentication, please see these important instructions. 4

Summary of the content on the page No. 5

Troubleshooting ISSUE SOLUTION No Dial Tone Check all connections to the NationPhone Router & Phone Adapter. Make sure that the green light on the NationPhone Router & Phone Adapter blinks only when the phone is off hook. If not, ensure that you have an Internet connection. Reboot your equipment. Phone Does Not Check all connections to the NationPhone Router & Phone Adapter. Make sure the Ring ring volume on the phone is properly adjusted. Reboot your equipment. Fast Busy Reboot your

Summary of the content on the page No. 6

DSL/PPPoE Set Up Follow the steps below to setup the NationPhone Router & Phone Adapter for your DSL/PPPoE Internet connection. BEFORE YOU BEGIN : These steps are only needed if your DSL connection requires a User Login and Password entry in order to connect to your DSL service. If so, you must have both your User Login and Password in order to complete these steps. For additional information regarding your User Login and Password, please contact your DSL service provider prior to begin

Summary of the content on the page No. 7

6. Click the Wan Setup tab. The following screen will appear in the browser. 7. Select PPPOE from the drop down menu for Connection Type. 8. In the empty field to the right of "PPPoE Login Name" enter your DSL login I.D. provided to you by your DSL provider. 9. In the empty field to the right of "PPPoE Login Password" enter your DSL password provided to you by your DSL provider. 10. Click the Submit All Changes button at the bottom of the screen. 11. The page will change to the fol

Summary of the content on the page No. 8

You will be redirected to the configuration page in 5 seconds. If not, you can click HERE to return to the configuration page. 12. Close the browser. 13. Pull out the power supply plug from your NationPhone Router & Phone Adapter. Wait 10 seconds, and then plug the power supply back into the Adapter. 14. The yellow STAT light will blink for up to one minute. Wait until both the yellow STAT and the Green ( lights are illuminated and have stopped blinking. 15. Talk on the phone and surf th

Summary of the content on the page No. 9

Troubleshooting If the Sipura Web Configuration page does not return to your browser after clicking the Submit All Changes button: 1. Unplug the power to the NationPhone Router and Phone Adapter. 2. Wait 10 seconds, and then plug the power back into the Adapter. 3. Repeat steps 3-15 above. If you are unable to surf the Web or use the NationPhone Adapter to make/receive calls: 1. Confirm your DSL/PPPoE Logon User I.D. and Password with your DSL provider. 2. Contact your DSL provid