Summary of the content on the page No. 1
Universal PVS Kit
Star Trac Fitness™
E-TR, E-TBT, E-RB, and E-UB
S-TR, S-TBT, S-RB, and S-UB
INSTALLATION MANUAL
STAR TRAC UNIVERSAL TV BRACKET INSTALLATION
1
Summary of the content on the page No. 2
TABLE OF CONTENTS Introduction ..............................................................................................................................................4 Before You Get Started .............................................................................................................................5 Warning and Caution ................................................................................................................................6 Install Your
Summary of the content on the page No. 3
E & S TBT, RB, and UB E & S TR STAR TRAC UNIVERSAL TV BRACKET INSTALLATION 3
Summary of the content on the page No. 4
ABOUT THIS MANUAL This manual is applicable to the STAR TRAC E-Series & S-Series Products. The manual is divided into eight sections, as follows: Introduction Provides an overview of each section within the manual. Before You Get Started Provides guidelines to help you have a successful installation. Warnings and Cautions Helpful safety tips to keep you out of harms way. Installing Your STAR TRAC Universal TV Bracket Provides a step-by-step instruction set for installing
Summary of the content on the page No. 5
CHECK FACILITIES PREPAREDNESS For a proper installation, please read this guide thoroughly and follow the instructions. Star Trac’s goal is to help you have a successful and reliable installation, for this reason we have come up with some helpful tips and check list to accomplish this goal. STAR TRAC UNIVERSAL TV BRACKET INSTALLATION 5
Summary of the content on the page No. 6
CAUTION: Disconnect power before doing any installation. Required Tool for Installation Supplied: • 5MM Hex Allen Key • 3MM Hex Allen Key • #2 Phillips Screwdriver • Flat Screwdriver STAR TRAC UNIVERSAL TV BRACKET INSTALLATION 6
Summary of the content on the page No. 7
INSTALLING YOUR UNIVERSAL TV BRACKET KIT The Star Trac Universal PVS Kit is different for each of your Star Trac E or S Series Cardio products. Make sure you have the proper kit for the E or S Series product you are installing. The E- & S-UB, E- & S-RB, E- & S-TBT, and E- & S-ST will follow the same basic steps for installation. To install the TV neck on the E-UB, E-RB, and E-TBT, and follow these steps: STEP1 Using a #2 Phillips screwdriver, to remove the (8) screws on the bac
Summary of the content on the page No. 8
STEP4 Remove the cap cover with the Star Trac logo from the plastics by removing the (2) screws using a #2 Phillips screwdriver. Retain the screws for later use. You will no longer need the cap cover and, if desired, you can store it away for any possible future use. STEP5 Remove the (2) M8 button head screws retaining the cross brace using the 5mm Hex Key. Found in the hardware kit. Retain the screws for later use. You will no longer need the cross brace and, if desired, yo
Summary of the content on the page No. 9
STEP7 Adjust the cap with the grommet into place. Using the 5mm Hex Key, tighten the M8 Button head screws to about 190 l b-in (21.5 N-m) of torque. Take the (2) Phillips head screws you removed from the original cap and snugly tighten screws down using a #2 Phillips screwdriver. STEP8 Connect the ground wire back to the display mount and connect the 12 pin serial cable back to the 12 pin socket on the display. And then, place the display front plastic onto the bac
Summary of the content on the page No. 10
To install the TV neck on the E-TR, follows these steps: STEP1 Using a #2 Phillips screwdriver, to remove the (8) screws from the upper back of the display. Place the cover some where safe to keep it from being damaged. Next, to remove the (6) screws from the lower back of the display. Place the cover with the other one. Retain all the screws for later use. STEP2 Now remove the upper cap cover that has the STAR TRAC logo on it. This cap is held in by the upper back cove
Summary of the content on the page No. 11
STEP4 Mount the Personal Viewing Screen on the Treadmill. Using the 5mm Hex Allen Key, screw in the (2) M8 Button heads at the base of the PVS. STEP5 Adjust the display cap up or down to align with the holes on the display front. Once the cap is aligned, tighten the button head screws with the 5mm Hex Allen Key. STEP6 Replace the top back plastic. Use a #2 Phillips screwdriver insert the (8) screws, retained from earlier step, into the plastic. Do Not tighten a
Summary of the content on the page No. 12
To install the TV neck on the S-UB, S-RB, and S-TBT, follows these steps: STEP1 Remove the TV hole cover: On the back side of the neck tubing, using a flat screwdriver, unclench the TV hole cover from the notch. (The cover is not used anymore, but you may save it for future use as you like.) STEP2 Install TV bracket: Using a 5mm Hex Allen Key, install the TV bracket to the neck tubing with a 8mm button head screw. STAR TRAC UNIVERSAL TV BRACKET I
Summary of the content on the page No. 13
To install the TV neck on the S-TR, follows these steps: CAP STEP1 Using a #2 Phillips screwdriver, to remove the (19) screws from the back of the display. Next, remove the back cover and the upper cap cover with “Star Trac Logo on it (You will no longer need this cap cover and, if desired, you can store it away for any possible future use). BACK COVER SCREWS STEP2 Take the TV bracket from package and remove the bubble wrap. Insert the bracket into the rectangle tube. U
Summary of the content on the page No. 14
To install the TV on the bracket follows these steps: 1. TV with 75x75mm mounting hole pattern: Hex Install your TV onto the bracket, by using a 3mm Allen Key to fasten (4) M4 socket head screws and (4) washers, as shown. And then, insert the tubing cap on the tube opening. 2. TV with 100x100mm mounting hole pattern: Step 1 If the mounting hole pattern on your TV is 75x75mm, you have to install the VESA bracket (packed with hardware kit) onto your TV with (4) M4 socket hea
Summary of the content on the page No. 15
STAR TRAC 14410 Myford Road Irvine, California 92606 Telephone: (800) 228-6635, (714) 669-1660 Fax: (714) 508-3303 http://www.startrac.com P/N: 620-7841, Rev. B STAR TRAC E&S SERIES UNIVERSAL PVS INSTALLATION MANUAL 15
