Summary of the content on the page No. 1
USER’S MANUAL
Part 2
2.4 GHz Expansion Handset 2300
Please also read
Part 1 — Important
Product Information
© 2002 Advanced American Telephones. All rights reserved.
AT&T and the Globe Design are trademarks of AT&T Corp. licensed to Advanced American Telephones.
Summary of the content on the page No. 2
Visit us at www.telephones.att.com © 2002 Advanced American Telephones. All rights reserved. AT&T and the Globe Design are trademarks of AT&T Corp. licensed to Advanced American Telephones. Printed in China. Issue 1AT&T 07/02
Summary of the content on the page No. 3
CONTENTS BEFORE YOU BEGIN . . . . . . 1 Parts List . . . . . . . . . . . . . . . 1 Compatiblity . . . . . . . . . . . . . 2 About Handset Registration . . 2 INSTALLATION . . . . . . . . . . 3 Charging Stand Installation . . . 3 Belt Clip . . . . . . . . . . . . . . . . 5 Headset . . . . . . . . . . . . . . . . 5 FEATURE SETUP AND OPERATION . . . . . . . 6 DEFAULT SETTINGS . . . . . . . 7 TECHNICAL SPECIFICATIONS . . . . . . . 8 CONTENTS CONTENTS
Summary of the content on the page No. 4
BEFORE YOU BEGIN Parts List Your box should include: This User’s Handset USER’S MANUAL Part 2 Manual 2.4 GHz Expansion Handset 2300 Please also read Part 1 — Important Product Information © 2002 Advanced American Telephones. All rights reserved. AT&T and the Globe Design are trademarks of AT&T Corp. licensed to Advanced American Telephones. Charging Stand NiCd battery pack 1 BEFORE YOU BEGIN BEFORE YOU BEGIN
Summary of the content on the page No. 5
Compatibility This AT&T 2300 expansion handset is compatible with the AT&T 2320, 2325, 2355 and 2365 telephones. You may add up to three expansion handsets to your compatible telephone, for a total of four handsets. If you try to install a fifth handset, registration will be blocked. About Handset Registration Each expansion handset must be individually registered with your AT&T 2320, 2325, 2355 or 2365 base. Registration happens automatically when you place this handset fully charged into your
Summary of the content on the page No. 6
INSTALLATION Charging Stand Installation NOTE: Install the charging stand away from electronic equipment, such as personal computers, television sets or microwave ovens. Avoid excessive heat, cold, dust or moisture. 1 Connect the power cord to an electrical outlet not controlled by a wall switch. Standard electrical outlet 3 INSTALLATION INSTALLATION
Summary of the content on the page No. 7
2 Install the handset battery. Use only AT&T Battery 3301, SKU# 91076. a) Remove battery b) Plug the battery pack compartment cover by connector into handset. pressing on indentation Place the battery pack and and sliding downward. wires in the compartment. c) Replace cover by sliding it on its track up over battery case until it snaps firmly into place. 3 Charge the handset battery. • Place the handset in the charging stand. • Charge the battery at least 12 hours. After the first charge, the
Summary of the content on the page No. 8
Belt Clip You can remove a) Pull clip b) Press tabs the belt clip away from on belt clip from the handset to into slots handset. remove. on back of handset to Headset reattach. You can use this telephone hands-free when you install any industry standard 2.5 mm headset (purchased separately). For best results use an AT&T 2.5 mm headset. Plug the headset into the jack located on the right side of the handset (under the small rubber flap). Do not force the connection, but make sure the plug f
Summary of the content on the page No. 9
FEATURE SETUP AND OPERATION FOR INSTRUCTIONS TO SETUP AND OPERATE THIS EXPANSION HANDSET, REFER TO THE MANUAL THAT CAME WITH YOUR ORIGINAL BASE TELEPHONE. 6 FEATURE SETUP AND OPERATION FEATURE SETUP AND OPERATION
Summary of the content on the page No. 10
DEFAULT SETTING DEFAULT SETTINGS FUNCTION: DEFAULT SETTING: Dial Method Tone Handset Volume 2 Ring Volume 6 External Ring Pattern 0 Internal Ring Pattern 1 Key Click ON 7 DEFAULT SETTINGS DEFAULT SETTINGS
Summary of the content on the page No. 11
TECHNICAL SPECIFICATIONS TECHNICAL SPECIFICATIONS Frequency Range 2400 MHz – 2483 MHz Channels 95 Channel Spacing 864 kHz Output Power 23 dBm Sensitivity -92 dBm Modulation GFSK Operating Temperature 0°C – 40°C Base Unit Voltage 96 – 144 Vrms (AC Voltage, 60Hz) Base Unit Voltage 9 Vdc (AC Adapter Output) Handset Voltage 3.6– 4.6 Vdc, 600mAh 8 TECHNICAL SPECIFICATIONS TECHNICAL SPECIFICATIONS
Summary of the content on the page No. 12
Summary of the content on the page No. 13
