Summary of the content on the page No. 1
Installation and Assembly: Wallmount for CPA100 and
Whiteboard
Model: A100IWBMOUNT
Maximum Load Capacity for Screen: 53 lb (24 kg)
Maximum Load Capacity for Projector : 13.5 lb (6 kg)
1 of 16 ISSUED: 04-08-08 SHEET #: 055-9094-2 06-06-08
3215 W. North Ave. • Melrose Park, IL 60160 • (800) 865-2112 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.
Summary of the content on the page No. 2
NOTE: Read entire instruction sheet before you start installation and assembly. WARNING • Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please call Peerless customer care at 1-800-865-2112. • This product should only be installed by someone of good mechanical aptitude, has experience with basic building construction, and f
Summary of the content on the page No. 3
Before you begin, make sure all parts shown are included with your product. A B Parts List Description Qty. Part # A wall mount assembly 1 055-1841 B projector tube 1 055-1839 C projector arm 1 055-1830 D adapter plate 1 055-1828 E hook bracket 2 055-1840 F vertical handle 2 055-1834 G horizontal handle 1 055-1858 H projector adapter plate 1 055-1822 CARRIAGE I slide plate 1 055-1821 J projector mount 1 PRG-1 K #10-32 x 0.375" phillips screw 18 520-1130 L M6 x 12 mm serrated washer head socket p
Summary of the content on the page No. 4
Parts List Continued UV WX Y Z Make sure that wall mount assembly (A) is level, use it as a template to mark the top two mouting holes. 1 Alternatively, the top two screws can be fastened 16" apart as detailed in step 2 while making sure that they are level. In order to set the desired height of bottom of screen in the lowest position, refer to dimension X from the chart below. PROJECTOR TOP MOUNTING HOLES A SCREEN X BOTTOM OF SCREEN FLOOR CHART Screen Size Dimension X 63" 36" 77'' 42" 4 of 16 I
Summary of the content on the page No. 5
Installation to Wood Stud Wall WARNING • Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. • Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power. • Never tighten in excess of 80 in. • lb (9 N.M.). • Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to ed
Summary of the content on the page No. 6
CINDER BLOCK SOLID CONCRETE Installation to Solid Concrete or Cinder Block WARNING • When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid part of the block, generally 1" minimum from the side of the block. Cinder block must meet ASTM C-90 specifications. It is suggested that a standard electric drill on slow setting i
Summary of the content on the page No. 7
Installation to Metal Stud Wall (Metal Stud Accessory Kit ACC 615 Required) WARNING • Drywall must be 1/2" or thicker, and metal stud must be 24 gauge or thicker. • Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. Drill six 1/2" holes through drywall and metal studs. NOTE: It may be necessary to drill 5/32" pilot holes prior to 2 drilling 1/2" holes. Refer to instruction sheet included with Peerles
Summary of the content on the page No. 8
Fasten three #10-32 x 0.375" phillips Slide projector tube (B) into top of wall mount K 4 screws (K) to carriage leaving three 3 assembly (A) and secure with two #10-32 x threads exposed. Attach retainer 0.375" phillips screws (K) as shown below. bushing (Y) and flanged bushing (X) to NOTE: Use correct set of mounting holes for Y wall mount assembly (A) using two the screen size as shown below. #10-32 x 0.375" phillips screws (K). X 63" SCREEN A NOTE: Twist tube B into wall mount K assembly (A)
Summary of the content on the page No. 9
Fasten two #10-32 x 0.375" phillips screws (K) into adapter plate (D) leaving three threads exposed as shown in 5 detail 1. Hook each vertical handle (F) onto #10-32 x 0.375" phillips screw (K) as shown in fig 5.1. NOTE: Use top slot for 77" screen or second slot from top for 63" screen. Fasten #10-32 x 0.375" phillips screws (K) through lower slot of vertical handle (F) that lines up with the lower hole in adapter plate (D). Hole location for 77" screen is shown in fig. 5.2. Securely tighten al
Summary of the content on the page No. 10
Insert hook brackets into screen as shown in detail 2 and fig. 7.1. Secure each hook bracket (E) with M6 x 12 mm 7 serrated washer head socket pin screw (L) as shown in fig. 7.2 and detail 3. SCREEN SCREEN BRACKET 63" SCREEN E 77" SCREEN DETAIL 2 fig. 7.1 SCREEN E L DETAIL 3 fig. 7.2 10 of 16 ISSUED: 04-08-08 SHEET #: 055-9094-2 06-06-08 Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.
Summary of the content on the page No. 11
Hook brackets (E) into adapter plate (D) as shown in fig. 8.1 and HOOK 8 detail 4. The hooks will go over the flange on the top and the bottom of E FLANGE hook bracket (E) into the slots as shown in detail 4 and detail 6. Fasten #10-32 x 1-3/8" socket pin screws (T) on each hook bracket (E), using security allen wrench (V) and tighten to wall plate as shown in detail 5. To remove screen from mount, loosen safety/security screws and lift screen D off of mount. CAUTION DETAIL 4 • Do not tighten s
Summary of the content on the page No. 12
Arrow on projector mount assembly (J) indicates front of mount. The arrow of projector mount assembly (J) should 10 face towards the round tube on projector arm (C). Fasten projector mount assembly (J) to projector arm (C) using two 1/4-20 x 1.0" hex head screws (N), four 0.25" ID nylon washers (P) and slide plate (I) as shown in fig. 10.2 and 10.3. Do not tighten 1/4-20 x 1.0" hex head screws (N) fully to allow for adjustment. Insert rectangle plug (S) into projector arm (C) as shown in fig. 10
Summary of the content on the page No. 13
Place projector arm (C) onto projector tube (B) as shown in fig. 11.1. Align projector arm (C) so that the holes in 11 projector tube (B) are in the middle of projector arm (C) slot. NOTE: This can be adjusted during final projector alignment if needed. Fasten projector arm (C) to projector tube (B) using two #10-32 x 3/8" serrated washer head socket pin screws (O) as shown in fig. 11.2 and detail 6. C B fig. 11.1 C B O DETAIL 6 fig. 11.2 13 of 16 ISSUED: 04-08-08 SHEET #: 055-9094-2 06-06-08
Summary of the content on the page No. 14
Attaching Adapter Plate to Projector Align shoulder on connection block opposite notch in CONNECTION 12 adapter plate (H). Attach adapter plate (H) to BLOCK connection block from projector mount assembly (J) SHOULDER using two #10-32 x 3/8" serrated washer head socket pin screws (O). H NOTCH INDICATES FRONT OF PROJECTOR O Attach adapter plate (H) to projector using 13 four M6 x 12 mm serrated washer head socket pin screws (L) and 0.25" spacers (M). NOTE: Shoulder of connection block indi- cates
Summary of the content on the page No. 15
Attaching Adapter Plate to Projector Mount WARNING • Do not lift more weight than you can handle. Use additional man power or mechanical lifting equipment to safely handle placement of the projector. Slide connection block with projector into projector mount assembly (J) as shown. Tighten captive screw to secure 14 projector to projector mount assembly (J). ARROW INDICATES FRONT OF MOUNT CONNECTION BLOCK J FRONT OF MOUNT CAPTIVE SCREW IMPORTANT: For security installations, insert one #10-32 x 1
Summary of the content on the page No. 16
Projector Alignment To adjust yaw (swivel): Loosen screw on projector mount assembly (J) indicated below until projector mount 16 can be rotated. Rotate mount to desired position and retighten screw. To adjust pitch (forward and backward tilt): Turn knob on back of mount as shown below. Pull knob out and turn by hand for easy adjustment or insert #2 phillips screwdriver in end of knob and turn. To adjust roll (side to side tilt): Turn knob on side of mount as shown below. Pull knob out and tu
