Summary of the content on the page No. 8
Grounding Procedure (For Flammable Materials Only) Grounding Procedure Pressure Relief Procedure (For Flammable Materials Only) This equipment stays pressurized until pressure is manually relieved. To help prevent serious injury from This equipment must be grounded to reduce the risk pressurized fluid, such as skin injection, splashing of static sparking. Static sparking can cause fumes fluid and moving parts, follow the Pressure Relief to ignite or explode. Grounding provides an escape
Summary of the content on the page No. 9
Setup/Startup Setup/Startup 6. If removed, install strainer. This equipment stays pressurized until pressure is manually relieved. To help prevent serious injury from pressurized fluid, such as skin injection, splashing fluid and moving parts, follow the Pressure Relief Procedure when you stop spraying and before cleaning, checking, or servicing the equipment. ti3430a 1. Perform Grounding Procedure (page 8) if using 7. Turn prime valve down. Turn pressure control coun- flammable materials.
Summary of the content on the page No. 10
Setup/Startup 10. Start engine: f. After engine starts, move choke to open. a. Move fuel valve to open. ti3312a ti18563a b. Move choke to closed. 11. Set main power switch ON. ti18552a ti18561a 12. Set pump valve ON (pump is now active). c. Set throttle to fast. ti6471a ti18568a 13. Set throttle to desired setting. d. Set engine switch ON. OFF ti18568a ON ti3315a e. Pull starter cord. ti18562a 10 3A2090A Operation
Summary of the content on the page No. 11
Setup/Startup 14. Increase pressure control enough to start pump. 19. Trigger gun again into flushing fluid pail until paint Allow fluid to circulate for 15 seconds. appears. Assemble tip and guard. 15 SEC. ti3442a 15. Turn pressure down, turn prime valve horizontal. Disengage gun trigger safety. ti6472a 20. Repeat steps 6 - 10 on second gun for 2-gun mod- els. 3304c ti3441a SwitchTip and Guard Assembly 16. Hold gun against grounded metal flushing pail. Trig- 1. Engage trigger safety. Use end
Summary of the content on the page No. 12
1 1 2 Gun Placement Gun Placement 3. Use the Gun Selector Switches to determine which Install Gun guns are active. Each gun selector switch has 3 positions: continuous line, OFF, and programmed 1. Insert gun into gun holder. Tighten clamp. line pattern. Programmed line pattern OFF position disengages gun Continuous line ti18969a ti18570a 2 Examples: Position Gun 2. Position gun: up/down, forward/reverse, left/right. See Gun Positions Chart, page 17 for examples. ti18574a Gun 1 Gun 2 ti185
Summary of the content on the page No. 13
Gun Placement 3. Slide gun arm assembly into desired gun arm Gun Arm Mounts mounting slot. This unit is equipped with front and rear gun arm mounts. ti18980a ti18556a 4. Tighten gun arm knob into gun arm mounting slot. ti18974a NOTICE ti18555a Make sure all hoses, cables, and wires are properly routed through brackets and do NOT rub on tire. Contact with tire will result in damaged hoses, cables, and wires. Change Gun Position Change Gun Position (Front and Back) (Left and Right) 1. Loo
Summary of the content on the page No. 1
Operation
LineLazer IV 250SPS
3A2090A
Self-Propelled Line Striper
EN
For the application of line striping materials.
For professional use only.
For outdoor use only.
Not for use in hazardous locations or explosive atmospheres.
Maximum Operating Speed: 10 mph (16 kph)
Maximum Operating Pressure: 3300 psi (22.8 MPa, 228 bar)
IMPORTANT SAFETY INSTRUCTIONS
Read all warnings and instructions in
this manual and the engine manual.
Save these instructions.
Model Guns Description
LLIV 250SPS (North
Summary of the content on the page No. 14
Gun Placement 3. Loosen gun mounting wing nut and remove gun 2. Install gun mount onto gun arm assembly and mount. tighten gun mount wing nut. ti18978a ti18979a ti18984a 3. Tighten gun arm knob into gun arm mounting slot. ti18985a 4. Slide gun arm assembly out from gun arm mounting slot. ti18976a ti18983a 4. Install guns into gun mounts. Installation 1. Slide gun arm assembly into gun arm mounting slot. ti18986a NOTE: Make sure all hoses, cables, and wires are properly routed through bracke
Summary of the content on the page No. 15
Gun Placement 3. Install cable end onto trigger plate pin and install Gun Cable Adjustment clip. Adjusting the gun cable will increase or decrease the gap between the trigger plate and the gun trigger. To adjust trigger gap, perform the steps below. + ti18987a ti18998a 4. Route cable around unit and up through cable holes 1. Use wrench to loosen locking nut on cable adjuster. behind hose mount. 2. Loosen or tighten adjuster until desired result is achieved. NOTE: More thread exposed means
Summary of the content on the page No. 16
Gun Placement Change Trigger Position Removal Installation 1. Remove both hand grips from handle bar (spraying 1. Route trigger wire to other side of handle bar. Make compressed air into end of handle grip works well sure wire is routed behind steering column, through for this). wire slot on steering plate, and into wire clamp on handle bar. ti18993a ti18988a 2. Install trigger assembly onto desired handle bar. 2. Use an allen wrench to loosen bolt on trigger mount- ing clamp. ti18991a 3. U
Summary of the content on the page No. 17
Gun Placement Gun Positions Chart 1 4 2 3 5 ti18553a 1 One line 2 One line up to 24 in. (61 cm) wide. 3 Two lines 4 One gun curb 5 Two gun curb 3A2090A Operation 17
Summary of the content on the page No. 18
Driving Instructions To turn right and left: Turn the handle bar right or left to Driving Instructions steer the LineStriper. Perform Startup, page 9. Use the handle bars of the LineStriper to control all motion during operation. In addition to steering the LineStriper, the handle bars also control forward and ti17518a reverse movement by pulling the forward/reverse control lever. NOTE: Make sure wheel motor bypass valve is engaged (see page 19). To move forward: Disengage brake and slowly
Summary of the content on the page No. 19
Driving Instructions 3. If striper arcs to the left, turn adjuster screw Drive Engagement counter-clockwise. The wheel motor bypass valve allows the operator to disengage the wheel tension and push the unit around. Rotate one complete turn counter-clockwise to disengage. ti18591a 4. Test-drive the striper. Repeat steps 2 and 3 until striper drives straight. Tighten two bolts on wheel alignment plate to lock the new wheel setting. + ti18576a ti18592a Straight Line Adjustment The f
Summary of the content on the page No. 20
Driving Instructions Platform Storage Position Front Pad Adjustment 1. Raise stand and pin self-locks. 1. Loosen four bolts. 2. Slide pad up or down to desired position. 4 bolts ti18560a ti19006a 2. To lower stand, pull pin and lower stand. 3. Tighten four bolts. ti18566a 20 3A2090A Operation
Summary of the content on the page No. 2
Table of Contents Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Smart Control Overview . . . . . . . . . . . . . . . . . . . . 21 Component Identification (Sprayer) . . . . . . . . . . . 6 Quick Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Component Identification (Controls) . . . . . . . . . . . 7 Smart Control Operation . . . . . . . . . . . . . . . . . . . . 22 Grounding Procedure Initial Setup . . . . . . . . . . . . . . . . . . . . .
Summary of the content on the page No. 3
Warnings Warnings The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclamation point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When these sym- bols appear in the body of this manual or on warning labels, refer back to these Warnings. Product-specific hazard sym- bols and warnings not covered in this section may appear throughout the body of this manual where applicable. WARNING TRAFFIC
Summary of the content on the page No. 4
Warnings WARNING ENTANGLEMENT HAZARD Rotating parts can cause serious injury. � Keep clear of moving parts. � Do not operate equipment with protective guards or covers removed. � Do not wear loose clothing, jewelry or long hair while operating equipment. � Equipment can start without warning. Before checking, moving, or servicing equipment, follow the Pressure Relief Procedure and disconnect all power sources. MOVING PARTS HAZARD Moving parts can pinch, cut or amputate fingers and other bod
Summary of the content on the page No. 5
Warnings WARNING BATTERY SAFETY The battery may leak, explode, cause burns, or cause an explosion if mishandled. � Only use the battery type specified for use with the equipment. See Technical Data. � Battery maintenance must only be performed or supervised by personnel knowledgeable of batteries and the required precautions. Keep unauthorized personnel away from battery. � Do not dispose of battery in fire. The battery is capable of exploding. � Follow local ordinances and/or regulations f
Summary of the content on the page No. 6
ON Component Identification (Sprayer) Component Identification (Sprayer) 1. 16. 15. 14. 11. 17. 2. 13. 12. 10. 3. 9. 8. 4. 5. 6. 7. ti15841a 10 Engine ON/OFF Switch 1 Operator Platform 11 Hydraulic Fill Cap / Dipstick 2 Paint Filter 12 Oil Filter 3 Prime / Drain Valve 13 Paint Hopper (25 gallon / 75 liter) 4 Displacement Pump 14 Handle Bar Height Adjustment Knob 5 Rear Gun Arm Mount 15 Engine Recoil Handle 6 Serial Label 16 Brake 7Gun Trigger Safety 17 Steering Handle 8 Wheel Motor Bypass
Summary of the content on the page No. 7
1 1 2 2 Component Identification (Controls) Component Identification (Controls) 5. 4. 3. 6. 2. 7. 1. on off 8. 10. 9. 11. ti18719a 1 Hydraulic Pump Valve 2 Gun Trigger Control 3 Forward / Reverse Lever 4Display 5 Engine Throttle 6 Engine Choke 7 Gun 1 Selector 8 Gun 2 Selector 9 Engine Kill / Main Power Switch 10 12V Accessory Jack 11 Pressure Control 3A2090A Operation 7
