Summary of the content on the page No. 1
Royal Sovereign LAMINATORS
OWNER'S MANUAL
RSS-1200,1050 ,685
PLEASE READ AND SAVE INSTRUCTIONS.
- 1 -
Summary of the content on the page No. 2
TABLE OF CONTENTS TOPICS PAGE INTRODUCTION --------------------------------------------------------------------------------- 3 SAFETY PRECAUTIONS --------------------------------------------------------------------- 3 CHARACTERISTICS ------------------------------------------------------------------------------ 4 SPECIFICATIONS ---------------------------------------------------------------------------------- 4 NAMES OF MAJOR PARTS OF MACHINE --------------------------------
Summary of the content on the page No. 3
INTRODUCTION Thank you for purchasing a Royal Sovereign Roll Laminator. It has been designed and manufactured to provide years of continuous service in the professional environment. To insure high quality lamination, please read this instruction manual thoroughly. This manual will provide you with complete operating and maintenance information. For additional product support or factory-direct ordering information. Call Royal Sovereign Customer Service at (800) 397-1025. SAFETY PRECAUTIONS
Summary of the content on the page No. 4
CHARACTERISTICS RS Roll Laminator Line are advanced laminators with time transcendental design, utilizing the latest in laminating technology. It is designed for you to set temperature and speed as necessary and have the machine remember your settings. Also, you can laminate anything at high speed, regardless of thickness of material and type of film. Remote control device allows for control of the machine from the front or rear. Foot-Pedal Switch allows for hands-free operation. It is also
Summary of the content on the page No. 5
NAMES OF MAJOR PARTS OF MACHINE 13 1 4 3 14 6 10 5 11 12 9 2 7 8 1. FILM-UPPER 8. FOOT SWITCH 2. FILM-LOWER 9. REMOTE CONTROL SWITCH 3. TAKE-UP (ASS'Y-TAKE-UP) 10.CONTROL PANEL 4. IDLER BAR (UPPER) 11.PRESSURE LEVER 5. TABLE-FRONT 12.TENSION CONTROL KNOB 6. SHOE-HEATER,UPPER 13.ALIGNMENT KNOB 7. ASS'Y-STAND 14.TAKE-UP SWITCH - 5 -
Summary of the content on the page No. 6
ADJUSTMENT OF FILM TENSION AND LOCATIONS Alignment Knob. Locking Nut Tension Control Knob Film 필름 열판 Shoe-Heater Anti-Wrinkle 주름방지부 device Film 필름 1. HOW TO CONTROL TENSION Tension of film can be controlled depending on the state of lamination, but basically you can adjust it, to some extent, and make wrinkles straighten from Anti-Wrinkle Part of the heat shoe. To increase the tension on the film, turn the knob clockwise. To lower the tension, turn the handle counter clockwise. If la
Summary of the content on the page No. 7
SETTING UP FILM Picture 1 Picture 2 Upper Film Picture 3 Lower Film Picture 4 Upper Film Picture 5 Core Fixing Lower Film Screw 1. Set the glossy side of upper/lower film to face the heat. ( Glossy side is PET film and matte side is thermal polymer laminating film.) 2. Like picture 1, insert core into the left side of upper/lower film shaft. 3. Like picture 2 and 3, insert core into the right side of upper/lower film. 4. Like picture 4 and 5, adhere core closely. (Make the right/left dir
Summary of the content on the page No. 8
HANGING FILM 1. HOT FILM UPPER ROLL FILM HEAT SHOE SHAFT LOWER IDLE BAR SHAFT UPPER IDLE BAR LOWER FILM HEAT SHOE GUIDING PAPER Picture 1 LOWER ROLL FILM LOWER IDLE BAR SHAFT 1. Insert the bar into the core of roll film then place the bar on the machine. 2. Place the Pressure Lever to the open mode (10~13mm). 3. Insert a piece of lightweight cardboard (Guiding Paper) between the rollers, through to beyond the second set of rollers. **IMPORTANT : It should reach beyond the second se
Summary of the content on the page No. 9
2. COLD FILM TAKE UP DEVICE UPPER FILM SHAFT PAPER BACK HEAT SHOE COLD FILM UPPER IDLE BAR 1. Take out the guiding table. 2. Put the shaft of roll film in each hole exactly. 3. Set the pressure lever to the proper lamination mode.(1mm/5mm/10~13mm) 4. Pull the film around the idler bar to the Anti-wrinkle device. 5. Put the paper back of the film to the bobbin at take-up bar to rewind the paper back. **It is to be stuck on to roll up clock wise. 6. Place the sticky part of film on the upper sh
Summary of the content on the page No. 10
CONTROL OF ROLLER PRESSURE ***Methods of controlling pressure of the roller *** 1. For setting, pull the pressure lever out and turn the lever to following the indication. 2. 10~13mm Board : Mode that you can laminate 10~13mm(1/3" to 1/2") 3. 5mm Board : Mode that you can laminate 5mm(1/4") hard board 4. 1mm hard board : Mode that you can laminate 1mm(40mil) hard board 5. Laminating : Mode that you can do laminate 25mic(1mil) to 250mic(10mil) - 10 -
Summary of the content on the page No. 11
INSTRUCTIONS FOR CONTROL PANEL You can manipulate speed and temperature with the LCD controller. We designed the LCD panel for user convenience by adopting memory working condition. ***Terms*** LCD DISPLAY BUTTON - 11 -
Summary of the content on the page No. 12
1.LCD WINDOW 1. Initial display status. It displays the last working condition when the power is turned on. is displayed 2. when the preset temperature is reached. Blinking 3. Indicates to wait till blinking stops. Current temperature is higher or lower than the preset temperature. 4. Saving electricity status. 5. Temperature 1) Shows the preset temperature. 2) You can check the current temperature on the heat shoe by pressing T-Check button. 6. S
Summary of the content on the page No. 13
2. FUNCTIONS OF BUTTONS UPPER : Upper shoe temperature controller UPPER SPEED LOWER : Lower shoe temperature controller MEMORY LOWER : Speed controller SPEED : Choose memorized working condition MEMORY ST/BY C/HOT T-CHECK : ① Increase temperature ② Increase speed ③ Restore the memorized working STOP RUN REV setting : ① Decrease temperature ② Decrease speed FAN MEANS RESET ③ Restore the memorized working setting C/HOT : Cold function T-CHECK : Check current temperat
Summary of the content on the page No. 14
3.HOW TO USE BUTTONS ***Set the upper/ lower heat shoes*** 1. Temperature available range from 0°C (32°F) Button & Display to 160°C (320°F). 2. Set temperature of upper shoe. Press upper button then you will see the LCD is blinking 6 times. Before blinking is finished, press or to set the temperature. 3. Set temperature of lower shoe. Press lower button and choose the arrow button UPPER the same way to set temperature of upper shoe. UPPER 4 Each time you press t
Summary of the content on the page No. 15
***Memorizing Working condition and Using the memorized working condition*** 1) Memorize working condition 1.Operator can memorize 9 working conditions. 2.Each time you press the button, buzzer is ringing. 3.find the condition number you are willing to memorize MEMORY working condition by pressing button. 4.When you finish setting upper/lower temperature and speed, you can press the memory button. UPPER SPEED This working condition is memorized while buzzer is ringing with blin
Summary of the content on the page No. 16
***Check current temperature on the shoes.*** 1.This function allows you to check the current temperature on the shoes. T-CHECK 2.Press then temperature is shown on the display while display is blinking. 3.It shows current temperature 5 times then returns to temperature which the operator has set. 4.It shows "LO" when the temperature is 40°c (104°F) or below. Only when the current temperature is over T-CHECK 41°c (106°F) will it show the exact temperature on T-CHECK on the shoes.
Summary of the content on the page No. 17
***STND-BY (Saving Electricity while you are not operating for a while)*** ST/BY 1. When press button will display on the screen and STND-BY mode is set at 80℃. 2. When machine is in mode, machine condition ST/BY wouldn’t work. Press the button and it will revert to the previous working. 3. When the machine runs, you can’t change it to the mode. STOP In this case, press the
Summary of the content on the page No. 18
LAMINATING STEPS 1. HOT LAMINATING 1. Properly plug in the machine. 2. Set up your film. 3. Turn on the power switch on the backside of the product. (Emergency Switch must be turned to the "OFF" position. 4. Set pressure lever to "Laminating" position. 5. Increase temperature of the hot shoe. If the temperature is memorized for the MEMORY laminator, please push button, then use or button to choose the correct location. 6. It is ready when the LCD window
Summary of the content on the page No. 19
***Useful Information*** 1. It would be easier for you to operate the machine next time if the tempreature and MEMORY the speed are set at the best condition and memorized by using the button 2. sign may appear on LCD window in the case continuous laminating. If it happens, the speed needs to be lowered by one speed level and started again after signal on the LCD window. 3. In case of wrinkling or rolling of film due to wrong position of document,
Summary of the content on the page No. 20
***Temperature/Speed adjustment guide*** Film Paper Preset User's Guidence NO Remarks Thickness Thickness Temp Speed Storage Temp Speed 130 9 100g/㎡ 38 micron 1 150g/㎡ 130 71 (1.5 mil) 300g/㎡ 130 5 100g/㎡ 110 3 80 micron 2 150g/㎡ 110 32 (3 mil) 300g/㎡ 110 2 100g/㎡ 110 2 100micron 3 150g/㎡ 110 23 (4 mil) 300g/㎡ 110 2 100g/㎡ 115 3 125micron 4 150g/㎡ 115 34 (5 mil) 300g/㎡ 115 2 100g/㎡ 120 3 150micron 5 150g/㎡ 120 35 (6 mil) 300g/㎡ 120 3 100g/㎡ 120 3 175micron 6 150g/㎡ 120 26 (7 mil) 300g/㎡ 120 1 10
