Summary of the content on the page No. 1
MODEL 37641401 - 02
PECO OWNERS MANUAL PECO OWNERS MANUAL PECO OWNERS MANUAL
PECO OWNERS MANUAL PECO OWNERS MANUAL
FOR A SCAG UNIT P# Q0119 FOR A SCAG UNIT P# Q0119 FOR A SCAG UNIT P# Q0119
FOR A SCAG UNIT P# Q0119 FOR A SCAG UNIT P# Q0119
CONGRATULATIONS AND THANK YOU FOR BUYING THIS PECO LAWN VACUUM.
Your new PeCo Vac has been engineered and manufactured to PeCo's high standards for
safety, quality and
Summary of the content on the page No. 2
WARRANTY PeCo Limited Warranty for New Products A. WHAT IS WARRANTED? B. SECURING WARRANTY F. NO REPRESENTATIONS PeCo extends the following ADJUSTMENTS ADDITIONAL WARRANTIES, warranties to the original Damaged or broken parts other DISCLAIMER. purchaser of each new PeCo than engines or batteries, must be Neither PeCo, Inc. nor any company consumer product subject to returned to PeCo, Inc., P.O. Box affiliated with it makes any the following limitations. 1197, Arden, NC 28704 before any warra
Summary of the content on the page No. 3
SAFETY Outdoor Power Equipment Institute Recommendations WARNING TO PURCHASERS OF INTERNAL COMBUSTION ENGINE EQUIPPED MACHINERY OR DEVICES IN THE STATE OF CALIFORNIA: The equipment which you have purchased does not have a spark arrester muffler. If this equipment is to be used on any forest covered and brush covered land or grass covered unimproved land in the state of California, the law requires that a spark arrester muffler be installed and be in effective working order. The spark arrester
Summary of the content on the page No. 4
ASSEMBLY MOWER FRAME STEP 1: Remove plate on rear of mower as shown. Redrill top two holes for a 3/8"-16 hex bolt to mount Mount Frame onto mower frame. HOLES TO MOUNT TO FIG. 1-1 TRACTOR DESIGNATION OF HOLES ON THE MOUNT PLATE STEP 2: B Use (2) 3/8"-16 x 2" (#K1208) and (2) 3/8"-16 flange nuts (#K1215) to secure Mount Plate (A) to mow
Summary of the content on the page No. 5
ASSEMBLY STEP 3: A Slide Engine Mount Arm (B) into the receiver on the Mount Plate (A) and fasten by dropping in ball pin (#J0248). Place Engine/ Blower Assembly onto Engine Mount Arm (B) and fasten with (4) 5/16"-18 x 1 1/2 hex bolts (#K1157) and (4) 5/16"-18 flange nuts. Tighten nuts and bolts. B STEP 4: A The ears of the Cone (A) should fit underneath
Summary of the content on the page No. 6
PARTS LIST REF. NO. PART NO. DESCRIPTION QTY. 1 B3749 BOOT PLATE 1 2 ******* BOOT (SPECIFY DECK SIZE) 1 3 J6006 7"- 8" HOSE CLAMPS 2 4 ******* 42" LOWER HOSE 1 5 ******* BLOWER CONE 1
Summary of the content on the page No. 7
EXPLODED VIEW MODEL 37641402 17 10 9 16 22 18 19 22 21 11 14 20 12 25 24 8 26 7 1 6 5 2 4 3 7 PeCo MODEL 37641401 - 04
Summary of the content on the page No. 8
ASSEMBLY STEP 5: Attach Wheel (A) to Caster Fork (B) by using (1) axle (B4236), (1) flat washer (K0017), (2) spacers E (S3315), (1) push nut (K0199), and (1) cotter pin (K0085). Next attach F assembled Caster (C) to Hitch (D) by using (2) 1" washers (K0064) and (1) cotter pin (K0089). Attach Hitch Assembly (D) to Main Frame (E) by using (4) 3/8"-16 x 2 1/2" hex bolts a
Summary of the content on the page No. 9
ASSEMBLY STEP 7: Attach Boot Retainer to Boot with 3/8" x 1" carriage bolts and 3/8" flange nuts as shown. TIGHTEN NUTS AND BOLTS! STEP 8: Lift mower deflector and hang Boot Plate as shown. STEP 9: Place Clamp over each end of Lower Hose. Attach one end of hose over the Blower Cone. Tighten Clamp. Slide free end of hose over Boot and tighten clamps.
Summary of the content on the page No. 10
MAINTENANCE Your Lawn Vac was designed and built to provide years of service with only minor care. Certain tasks however must be performed to keep it in good operating condition and to avoid costly repairs. This section describes and provides procedures for the necessary care of the Lawn Vac. CARE REQ SCHEDULED CARE UIRED Check engine oil. Before Each Use Check all hose connections. After Each Use Clean Collector Box, hoses and engine of
Summary of the content on the page No. 11
TROUBLE SHOOTING Diagnostic Procedures Trouble shooting procedures are provided in the chart below. To use these procedures, first locate the problem description that best describes the trouble that you have encoun- tered. Check the possible causes one at a time in the list. Correct any problems that are found and operate the vacuum collector again to verify that you have eliminated the problem. DO NOT attempt any major repairs without first contacting your dealer. PROBLEM CAU
Summary of the content on the page No. 12
P.O. Box 1197 Arden, North Carolina 28704 1-800-438-5823 or (828) 684-1234 fax-(828) 684-0858 email: peco@ioa.com PeCo MODEL 37641401 - 04