Summary of the content on the page No. 1
TM 9-6695-244-34P
DEPARTMENT OF THE ARMY TECHNICAL MANUAL
DIRECT SUPPORT AND GENERAL SUPPORT MAINTENANCE
REPAIR PARTS AND SPECIAL TOOLS LIST
FOR
POWER MAINFRAME, TEKTRONIX MODEL TM506
(NSN 6625-01-048-8920)
Current as of 5 December 1979
Headquarters, Department of the Army, Washington, DC
4 January 1980
REPORTING OF ERRORS
You can help improve this publication by calling atten-
tion to errors and by recommending improvements and
stating your reasons for the recommendations. Your
letter
Summary of the content on the page No. 2
TM 9-6695-244-34P Section I INTRODUCTION 1. Scope. This manual lists spares and repair parts that are required for maintenance of the Power Mainframe, Tektronix Model TM506. It authorizes the requisitioning and issue of spares and repair parts as indicated by the source and maintenance codes. 2. General. This repair parts and special tools list (RPSTL) is divided into the following sections: a. Section I. Introduction. b. Section II. Repair Parts List. A list of spares and repair parts author
Summary of the content on the page No. 3
PG - Item procured and stocked to provide for sustained support for the life of the equipment.. It is applied to an item peculiar to the equipment which, because of probable discontinuance or shutdown of production facilities, would prove uneconomical to reproduce at a later time. KD - An item of a depot overhaul/repair kit and not purchased separately. Depot kit defined as a kit that provides items required at the time of over-haul or repair. KF - An item of a maintenance kit and not purchase
Summary of the content on the page No. 4
Code Application/Explanation C - Crew or operator maintenance performed within organizational maintenance. O - Support item is removed, replaced, used at the organizational level. F- Support item is removed, replaced, used at the direct support level. H - Support item is removed, replaced, used at the general support level. D - Support items that are removed replaced, used at depot, mobile depot, or specialized repair activity only. (b) The maintenance code enteredin the fourth position indicat
Summary of the content on the page No. 5
H. - Reparable item. When uneconomically reparable, condemn and dispose at the general support level. D - Reparable item. When beyond lower level repair capability, return to depot. Condemnation and disposal not authorized below depot level. L - Reparable item. Repair, condemnation, and disposal not authorized below depot/specialized repair activity level. A - Item requires special handling or condemnation procedures because of specific reasons (i.e., precious metal content, high dollar value,
Summary of the content on the page No. 6
h. Quantity Incorporated in Unit. Indicates the quantity of the item used in the breakout shown on the illustration figure, which is prepared for functional group, subfunctional group, or an assembly. A "V" appearing in this column in lieu of quantity indicates that no specific quantity is applicable (e.g., shims, spacers, etc). 4. Special information a. Repair parts for components of standards sets which can be identified as existing in the supply system will be requisitioned through normal
Summary of the content on the page No. 7
(2) Second. Using the repair parts listing, find the functional group to which the repair part belongs and locate the item by description. b. When NSN or reference is known: (1) First. Using the index of NSN's and reference numbers, find the pertinent NSN or reference number. This index is in ascending NSN cross-referenced to the illustration figure number and item number. (2) Second. Using the repair parts listing, find the figure and item number, and locate the figure and item numbe
Summary of the content on the page No. 8
M ---------------thousand RPM------------ revolutions per minute MA ---------- milliampere S ------------- single MAX ----------maximum SEC---------- seconds MC ---------- megacycles SECT ---------- section MFD --------- millifarads SERR-------- serrated MFR ----------manufacturer SHK ---------- shank MG ---------- milligrams SNG ---------- single MHZ ----------megahertz SPEC ---------- specification MIN ---------- minimum, minutes SPL ---------- special ML ---------- milliliters SQ --------
Summary of the content on the page No. 9
SECTION II. REPAIR PART LIST (2) (7) (1) (5) (8) (6) (3) (4) ILLUSTRATION QTY INC DESCRIPTION NATIONAL (b) (a) SMR IN PART STOCK ITEM FIG CODE U/M FSCM UNIT NUMBER USABLE ON CODE NUMBER NO. NO. GROUP 6691 MAINFRAME, POWER MOD TM506 80009 MSI30526/1TY1 18876 1 10 PAFZZ 5340-00-062-5431 348 0191-00 80009 UMPER.PLASTIC EA 1 1 20 PAFZZ 6225-01-018-2369 161-0033-04 80009 CABLE ASSEMBLY POWER EA 1 1 30 PAFZZ 5910-00-546-3271 283-0024-00 80009 CAPACITOR,FIXFED EA 1 1 40 PA
Summary of the content on the page No. 10
(1) (7) (8) (6) (2) (3) (4) ILLUSTRATION (5) QTY INC (a) (b) DESCRIPTION NATIONAL IN FIG ITEM SMR STOCK PART U/M UNIT NO. NO. USABLE ON CODE CODE NUMBER NUMBER FSCM 1 360 PAFZZ 5310-00-655-6534 40T10 52983 NUT,PLAIN ASSEMBLED EA 4 1 370 PAFZZ 5310-00-845-7736 NAS671B6 80205 NUT,PLAIN, .HEXAGCN EA 2 1 380 PAFZZ 5310-00-836-3520 511-041800-00 78189 NUT,PLAIN,ASSEMBLED EA 2 1 390 PAFZZ 5310-00-841-8106 210-0457-00 80009 NUT,,PLAIN,HEXAGON EA 7 1 400 PAFZ
Summary of the content on the page No. 11
SECTION III NATIONAL STOCK NUMBER AND PART NUMBER INDEX FIGURE ITEM FIGURE ITEM STOCK NUMBER NO. NO. STOCK NUMBER NO. NO. 5305-00-0C5-C795 1 530 5935-00-599-8548 1 140 5310-00-006-8205 1 350 5305-00-625-9546 1 460 5920-00-056-6620 1 230 5305-00-638-0502 1 523 5340-00-062-5431 1 10 5310-00-655-6534 1 360 5920-00-082-7561 1 200 5940-00-682-2477 1 703 5905-00-110-C992 1 420 5961-00-724-2138 1 660 4140-00-113-C989 1 170 4140-03-726-9755 1 150 5310-00-113-1494 1 73C 414C-00-726-9755 1 160 5961-00-13
Summary of the content on the page No. 12
By Order of the Secretary of the Army: E. C. MEYER General, United Sta tes Army Official: Chief of Staff J. C. PENNINGTON Major General, United States Army The Adjutant General Distribution: To be distributed in accordance with DA Form 12-34A, requirements for Calibration Procedures Publications *U.S. GOVERNMENT PRINTING OFFICE: 1980-640217/311
