Summary of the content on the page No. 1
OUTDOOR STORAGE
OUTDOOR STORAGE BUILDING
OWNER’S MANUAL
MODEL 6424
30” OUTDOOR STORAGE EXTENSION KIT
Copy
Summary of the content on the page No. 2
**A MINIMUM OF TWO ADULTS ARE REQUIRED FOR ASSEMBLY** BEFORE BEGINNING ASSEMBLY Identify and inventory all parts using the checklist boxes on the Parts List. Keep the hardware bags and their contents separate. If any parts are missing, call our Customer Service Department. SAFETY INSTRUCTIONS Failure to follow these safety instructions may result in serious injury or property damage. Proper and complete assembly, use and supervision is essential for proper operation and to reduce the risk of
Summary of the content on the page No. 3
HARDWARE IS ACTUAL SIZE (Unless otherwise indicated) AB AA AC AD TA TB 117 108 114 TE TJ TD TI 110 125 TF TK AE TH If you are Installing a New Shed 1. Check contents of boxes and compare to parts listed on the Parts List. 2. Follow instructions that came with your shed, but add extra floor panel, wall panels, Roof Cap and Skylight at appropriate points in the assembly. If you are Extending an Existing Shed 1. Remove any bolts or screws being used to anchor the shed to the ground. 2. Remove any o
Summary of the content on the page No. 4
**Save all hardware for re-assembly!** 1 a. Remove last three skylights. 2 a. Remove the back 3 roof caps. 3 a. Remove the back Roof panels and Roof support bars. 4
Summary of the content on the page No. 5
4 a. Remove the next Roof panels and Roof support bars. 5 a. Remove the Roof Truss. 5
Summary of the content on the page No. 6
6 a. Remove the last two Side Wall Panels. Note: If you’re adding onto a side entry shed, remove the panels (in gray) from the side of the shed rather than removing the back of the shed. If you’re adding on to both sides, remove the panels (in gray) from both sides of the shed (as illustrated), and follow the remaining steps. 7 a. Slide the back section of the shed away from the front. You will need to tip the back section forward slightly in order to disconnect the floor panels Be sure th
Summary of the content on the page No. 7
Assemble Window 8 TF (1) a. Remove plastic sheeting from Window (AE) and slide Window into slot TH (4) on the Window Wall Panel (125). Attach a Window Latch (TK) above each corner of the Window as shown. When tightening screws (TH), be sure that Window Latches will slide freely. Do not overtighten. Insert screw (TF) TK (2) into the hole in the window. Set panel aside. AE Insert window with bent edge at top and pointing away from the wall. Place Screw (TF) in this hole to keep window fro
Summary of the content on the page No. 8
9 a. Add new Floor Panel (110). Then, slide the back section into place and connect the floor panels (you will need to tip the panels forward slightly to connect the panels). Tip up one floor panel and line up tabs and then lay floor panel flat. 10 a. Add Wall Panels (108). Insert a wood block directly under the tab you want to insert, then slide block to next tab and repeat. 8
Summary of the content on the page No. 9
11 Assemble Truss TF (6) TE (6) a. Attach Brace (AC) to two Roof Truss Channels (AB) (one on each side of Brace. Secure Brace with Screws (TF) and Nuts (TE). Follow picture above to connect Brace to a Truss Channel at each end of the Brace. The nut goes on outside of the truss. b. Use Truss Connector (TA) to attach Roof Truss Channels at top. Secure with Screws (TF) and Nuts (TE). Before completely tightening, lay assembly on its side to be sure Channels and Brace are parallel. Complet
Summary of the content on the page No. 10
c. Slide a Threaded Rod through the Truss Support Brace and the top of the Truss Connector. TD (2) TB TB d. Secure the top and bottom of the Threaded Rod with a 1/4” Cap Nut (TD). TD WARNING Do not overtighten the Cap Nut. TD 10
Summary of the content on the page No. 11
12 a. Add Truss. 13 a. Add Roof Panels (114) and Roof Supports (AD). Roof Panel Ridge Roof Panel Wall b. Add a center Roof Cap (117). 11
Summary of the content on the page No. 12
14 a. Add next Truss. 15 a. Add Roof Panels (114) and Roof Supports (AD). b. Add a center Roof Cap (117). 12
Summary of the content on the page No. 13
16 a. Add Roof Panels (114) and Roof Supports (AD). b. Add the last Center Roof Cap (117) and the End Roof Cap. 17 a. Add Skylights 13
Summary of the content on the page No. 14
® Enhance your Lifetime Outdoor Shed by purchasing the following Shed Accessories: Model # 0110 Corner Shelf (2 pack) Two 10” radius shelves with hardware. 0130 30” Shelf Kit w/ hardware (3 pack) Three 30” x 10” Steel-Reinforced Shelves with shelf brackets and hardware. 0150 90” Shelf Kit w/ hardware One 90” x 9” Steel-Reinforced Shelf with shelf bracket and hardware. 0113 16” Pegboard Strips w/ hardware Two sixteen inch Pegboard Strips with hooks. Great for hanging large items such as: r
