Summary of the content on the page No. 1
Installation & Operating Manual
P61-2 Pellet Stove Owners Manual
Safety Testing by
ASTM E1509
Mobile Home Approved
ìCe manuel est disponible en FranÁais sur demandeî
R5
SAFETY NOTICE
PLEASE READ THIS ENTIRE MANUAL BEFORE YOU INSTALL AND USE YOUR NEW ROOM HEATER. FAILURE TO
FOLLOW INSTRUCTIONS MAY RESULT IN PROPERTY DAMAGE, BODILY INJURY, OR EVEN DEATH.
FOR USE IN THE U.S. AND CANADA. SUITABLE FOR INSTALLATION IN MOBILE HOMES
IF THIS HARMAN STOVE IS NOT PROPERLY INSTALLED, A HOUSEFIRE MAY RESU
Summary of the content on the page No. 2
Fig. 1 2
Summary of the content on the page No. 3
Table of Contents Testing Label 2 Assembly & Installation 4 Venting 7 Operation 12 ESP Control 14 Maintenance 15 Trouble Shooting 18 Feeder Parts 19 Specifications 19 Wiring Diagram 20 Options 22 Parts List 23 Warranty 24 Please read this entire manual before you install and use your new room heater. Failure to follow instructions may result in property damage, bodily injury, or even death. SUITABLE FOR MOBILE HOME INSTALLATIONS. SAVE THESE INSTRUCTIONS Harman Stove Company 352 Mountain House R
Summary of the content on the page No. 4
Assembly and Installation Unpacking The P61 is bolted to the skid to prevent move- ment during shipping. To free the stove from the skid you must re- move the hold-down bolts in the rear of the pedestal base. Removing or Installing rear cover panels To remove the rear cover panels, loosen the screws slightly and slide the covers outward as shown in the illustration. To reinstall, simply slide back into place and retighten the screws. Firebrick Install the firebrick vertically on the ang
Summary of the content on the page No. 5
FLOOR PROTECTOR Installation Installing Place the stove on a noncombustible floor or UL approved floor protector that extends 6 inches to the front, 6 inches to the sides and 1 inch to the rear of the 9"-13" stove. Place the stove away from combustible walls at least as far as shown in figures 3,4 and 5. Please note the difference in side wall clearance with and without side shields. Note that the clearances shown are minimum for safety but do not leave much room for access when cleaning or ser
Summary of the content on the page No. 6
Venting Requirements for Terminating the Venting WARNING: Venting terminals must not be re- J. The clearance to a non-mechanical air sup- cessed into a wall or siding. ply inlet to the building or the combustion air inlet to 1 NOTE: Only PL vent pipe wall pass-throughs any other appliance must be a minimum of 48î. and fire stops should be used when venting through K. The clearance to a mechanical air supply 1 combustible materials. inlet must be a minimum of 10 feet. NOTE: Always take into consi
Summary of the content on the page No. 7
Venting A combustion blower is used to extract the com- bustion gases from the firebox. This causes a nega- IMPORTANT NOTICE tive pressure in the firebox and a positive pressure Pellet Vent Pipe or PL Vent Pipe Must be used. in the venting system as shown in fig. 6. The longer the vent pipe and more elbows used in the system, the greater the flow resistance. Because of these facts we recommend using as few elbows as pos- sible and 15 feet or less of vent pipe. The maximum horizontal run should n
Summary of the content on the page No. 8
Venting Venting #1 Preferred method This method provides excellent venting for nor- mal operation and allows the stove to be installed closest to the wall. Two inches from the wall is safe; however, four inches allows better access to remove the rear panel. The vertical portion of the vent should be three to five feet high. This vertical section will provide natural draft in the event of a power failure. Fig. 8 3 ft. to combustibles #2 Preferred method This method also provides excellent venting
Summary of the content on the page No. 9
Venting Venting #4 Installing into an existing chimney ( US only ) This method provides excellent venting for nor- mal operation. This method also provides natural draft in the event of a power failure. If the chimney condition is questionable you may want to install a liner as in method #7. Fig. 10 #5 Installing into an existing fireplace chimney ( US only ) This method provides excellent venting for nor- mal operation. This method also provides natural draft in the event of a power failure.
Summary of the content on the page No. 10
Venting Venting #6 Installing into an existing fireplace chimney ( US and Canada ) This method provides excellent venting for nor- mal operation. This method also provides natural draft in the event of a power failure. In Canada and some places in the US it is re- quired that the vent pipe extend all the way to the top of the chimney. In this method a cap should also be installed on the chimney to keep out rain. Be sure to use ap- proved pellet vent pipe fittings. Seal pipe joints with silicon
Summary of the content on the page No. 11
Venting Storm collar Flashing 3" min. 3" min. 3" min. Minimum flue vent PL vent manufacturer's No insulation or firestop spacer and support configuration other combustible materials are It is recommended that allowed within 3" outside air be installed with this of the PL vent pipe. venting configuration. (See Page 9 for corner installation clearances) Fig. 14 Fig. 15 #8 Installing through the ceiling vent Through the ceiling vent, follow PLvent manufacturers recommendations when using wall an
Summary of the content on the page No. 12
P61-2 MANUAL START UP Operation Starting First Fire Be sure the power cord is plugged into a 120 volt receptacle. This can be verified by the red power light on the control panel. Fill the hopper with pellets. Fill the burn pot with pellets to a level just short of overflowing, fig. 17. Adjust feed rate. If this is your first fire or you are Fig. 17 trying different pellets, set the feed adjuster to "3", fig. 18. This is a conservative number and will prob- ably need to be increased. After y
Summary of the content on the page No. 13
P61-2 MANUAL IGNITION/OPERATION When to use "Stove Temp Mode" In "Stove Temp Mode" the Stove Temp Dial de- termines the temperature of the stove. Heat output and fuel consumption will remain constant. This makes it possible to tell how long a hopper full of pellets will last. The distribution blower speed will Fig. 21 vary according to the position of the mode selector, fig. 21. When to use "Room Temp Mode" In "Room Temp Mode" heat output is controlled automatically by the Room Sensing P
Summary of the content on the page No. 14
ESP CONTROL P61-2 ESP CONTROL Feed adjuster Power Light Sets the maximum Indicates power to the feed rate control. Test Runs all motors at full speed for two minutes to check Status Light operation. After two Will be lit in either stove minutes the stove or room temp mode when will go to minimum pointer is not within off burn and the position band except blowers will after normal shut down. alternate from high Blinks to indicate errors to low every two listed listed below. minutes to remind yo
Summary of the content on the page No. 15
Room Sensor and Rear Shield Installation Rear Shields Room Sensor Installation 5/16" Hex Head 5/16" Hex Head Screws (2 Screws (2 on on each each side) side) Fig. 22 Fig. 23 The room sensor is a small temperature sen- The rear isolated shields are split in the middle for sor on the end of a 60" gray wire. This sensor is easy removal. Each shield has two 5/16" hex head installed much like a standard wall thermostat. Be- screws that only need to be loosened (NOT cause it is so small, it can be hidd
Summary of the content on the page No. 16
Maintenance Removing Ashes: When approximatly 1 ton of pellets has been burned it will be necessary to empty the ash pan. Ashes should be placed in a metal con- tainer with a tight fitting lid. The closed con- tainer of ashes should be placed on a non- combustible floor or on the ground, well away from all combustible materials, pending final disposal. If ashes are disposed of by burial in soil or otherwise locally dispersed, they should be retained in the closed container until all cinders hav
Summary of the content on the page No. 17
Maintenance 7. Open burn pot slide as shown, clean with vacuum and close. 8. Clean heat exchanger with scraper as shown at left. 9. Brush or scrape the inside of the stove to remove fly ash. 10. Scrape burnpot with flat end of scraper pro- vided with the stove. Fig.31. Fig. 26 Fig. 27 Latch "closed "with Latch "open "with 11.Slide ash pan into stove and latch into place. blower cover in place. blower cover partly Burn pot clean-out is removed. Burn pot closed. clean-out is open. Brush not suppl
Summary of the content on the page No. 18
Trouble-Shooting FEEDER DOES NOT FEED SMOKE SMELL 1. No pellets in hopper. Seal the vent pipe joints and connection to stove 2. Feed motor will not run until ESP with silicone. senses 165 deg. F. Maybe you did not put FIRE HAS GONE OUT enough pellets in the burn pot before lighting 1. No pellets in hopper. the fire. 2. Feed rate too low. 3. Feed motor has failed. 3. Something is restricting fuel flow. 4. Something is restricting flow in the hopper 4. Feed motor or draft motor has failed. or ca
Summary of the content on the page No. 19
P61-2 Feeder and Specifications Specifications 23.5" 9" 5.250" Weight 249 lbs. Blower 135 cfm Feed Rate .75 to 7.5 lbs. per hr. Hopper Capacity 72 lbs. Fuel Wood Pellets Flue Size 3 inch Outside Air Size 2 3/8 I.D. inch Fuse Rating 5 amp 19 12.375" 34.5" 32.375" 29.5"
Summary of the content on the page No. 20
P61-2 Wiring Diagram 20
