Summary of the content on the page No. 1
SHERWOOD INDUSTRIES IS AN ENVIRONMENTALLY RESPONSIBLE COMPANY. THIS MANUAL IS PRINTED ON RECYCLED PAPER.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
PELLET STOVE
Ber n
OWNER’S MANUAL
� � � �
PLEASE READ THIS ENTIRE MANUAL BEFORE INSTALLATION AND USE
OF THIS PELLET-BURNING ROOM HEATER. FAILURE TO FOLLOW THESE
INSTRUCTIONS COULD RESULT IN PROPERTY DAMAGE, BODILY INJURY
OR EVEN DEATH.
Contact your building or fire officials about restrictions and installation
inspection requirements in
Summary of the content on the page No. 2
Table of Contents Introduction..............................................................................................................3 Pellet Quality..................................................................................................3 Automatic Safety Features of Your Pellet Stove.................................................3 Important Safety Data....................................................................................4 Safety Warnings And Recommendations.
Summary of the content on the page No. 3
Introduction * This manual is designed for the home owner in conjunction with the technical manual. * PELLET QUALITY: Pellet quality is important, please read the following: Your enviro pellet stove has been designed to burn wood pellets only. Do not use any other type of fuel, as this will void any warranties stated in this manual. The performance of your pellet stove is greatly affected by the type and quality of wood pellets being burned. As the heat output of various quality wood pellets d
Summary of the content on the page No. 4
Introduction IMPORTANT SAFETY DATA: Please read this entire Owner’s Manual before installing or operating your ENVIRO Pellet Stove. Failure to follow these instructions may result in property damage, bodily injury or even death. Contact your local building or fire official to obtain a permit and any information on installation restrictions and inspection requirements for your area. To prevent the possibility of a fire, ensure that the appliance is properly installed by adhering to the instal
Summary of the content on the page No. 5
Introduction ASHES: Disposed ashes should be placed in a metal container with a tight-fitting lid. The closed container of ashes should be on a non-combustible floor on the ground, well away from all combustible materials pending final disposal. The ashes should be retained in the closed container until all cinders have thoroughly cooled before disposing of them. ELECTRICAL: The use of a surge protected power bar is recommended. The unit must be grounded. The grounded electrical cord should
Summary of the content on the page No. 6
Introduction RATING LABEL LOCATION: The rating label is located on the inside of the ash pan cover. APPLIANCE DIMENSIONS: 1 1 5 / 2 " ( 3 9 3 m m ) 7 7 1 7 / 8 " 18 / 8 " ( 4 5 5 m m ) ( 4 81 m m ) 7 33 / 8 " ( 86 1 m m ) 1 5 1 7 / 2 " 1 9 / 8 " ( 4 4 4 m m ) ( 4 97 m m ) Figure 1: Dimensions of Bern. 6
Summary of the content on the page No. 7
Operating Instructions CONTROL BOARD FUNCTIONS: 1. AUGER TRIM: Used to change feed rates on LOW ONLY for poorer quality fuels. Push the Auger Trim button until the number 1 and 5 lights appear on the Heat Level Indicator. This will increase the feed rate to 2.5 seconds ON time Auger pulse. This is done only on LOW to allow the burning of poor quality fuels. Push the button until the number 1 and 4 lights appear, this will reduce the Auger On time to 1.5 second. This setting is for high-g
Summary of the content on the page No. 8
Operating Instructions OPERATING YOUR PELLET STOVE: PRE-BURN INSTRUCTIONS: The burn pot liner holes must be clear and the liner installed properly against the ignitor tube for proper operation. Check the hopper for enough pellets to start the unit. DO NOT OPERATE THE UNIT WITH THE DOOR OR ASH PAN OPEN. MANUAL MODE: To START: Press the ON / OFF button. The stove will turn on. The system light will flash. The Auger Light will flash with each pulse of the auger (the Auger Feed Rate is pre-pro
Summary of the content on the page No. 9
Operating Instructions SLIDER/DAMPER SET-UP: A i r In t a k e B ox S l i d e r D am per E x haust C hannel E x haust B l o w er Figure 4: Slider/Damper Plate in Unit. If the fire should happen to go out and the heat output indicator has been set on the lowest setting, the Slider Damper should be pushed in slightly, decreasing the air in the firebox or adjust the auger trim. If, after long periods of burning, the fire builds up and over flows the burn pot or there is a build up of clinkers, thi
Summary of the content on the page No. 10
Routine Cleaning and Maintenance The following list of components should be inspected and maintained routinely to ensure that the appliance is operating at its’ optimum and giving you excellent heat value: 2-3 Days / Weekly Semi-annually or 2 Tons of Fuel B ur n P o t L i n e r Burn Pot and Liner Exhaust Vent Heat Exchanger Tubes Air Intake Ash Pan Blower Mechanisms Door Glass Heat Exchanger Tubes A i r I n t a k e T ub e Inside Firebox Behind Firebox Liners & Covers Ash Pan and Door Gaskets Al
Summary of the content on the page No. 11
Routine Cleaning and Maintenance If the glass has build up that can not be removed with only the cloth, clean the glass using paper towel and a gas appliance glass cleaner, this may be purchased through most dealers. If a gas appliance glass cleaner is not available, use a damp paper towel dipped in fly ash to clean the glass. After the glass has been cleaned use the dry soft cloth to wiping down the outside and inside of the glass. ASH PAN (weekly) H eat ex c hang e r tub e s This part is l
Summary of the content on the page No. 12
Routine Cleaning and Maintenance Removal of the firebox backing. • Open the door by lifting the handle, remove the burn pot and burn pot liner. • Lubricate all screws with penetrating oil. • Remove the four (4) screws that hold the side panels in place. • With the tip of a flat screwdriver, gently lift up the side panels and remove the side panels. • Pull the center panel out. • Vacuum thoroughly. Installation of firebox backing: • Insert center panel. • Place the side panels back into the fire
Summary of the content on the page No. 13
Warranty Sherwood Industries Ltd. gives a five year limited warranty on all steel manufactured parts. A one-year warranty is provided on all electrical components. The above limited warranties are extended only to the original purchaser. There is no warranty on the following parts: ● Glass window ● Fiberglass rope gaskets ● refractory material ● burn pot liner ● paint ● enamel finish or gold plating where it applies **NOTE: The paint on the brick firebox lining may peel. This is due to the e
Summary of the content on the page No. 14
Installation Data Sheet The following information must be recorded by the installer for warranty purposes and future reference. NAME OF OWNER: NAME OF DEALER: _________________________________________ _________________________________________ ADDRESS: ADDRESS: _________________________________________ _________________________________________ _________________________________________ _________________________________________ _________________________________________ _____________________________
