Summary of the content on the page No. 1
Tested and Listed by
564 SS GreenSmart™
Fireplace
OMNI-Test Laboratories, Inc.
Beaverton, Oregon
• Operation
Report # 028-F-80b-5
• Maintenance
ANSI Z21.88a-2003
WARNING: If the information in these instructions is not followed exactly, a fire or
explosion may result causing property damage, personal injury or loss of
life.
- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this
or any other appliance.
WHAT TO DO IF YOU SMELL GAS
• Do
Summary of the content on the page No. 2
2 Introduction Introduction We welcome you as a new owner of a 564 SS gas fireplace. This manual details operation and maintenance of this fireplace. Please familiarize yourself with the Owner's Manual before operating your heater and save the manual for future reference. Important Information No other 564 SS gas fireplace has the same serial Register your warranty online at: number as yours. The serial number is on the listing label that is chained to the gas control valve. This tr
Summary of the content on the page No. 3
Introduction 3 Table of Contents Introduction and Important Information Maintenance Introduction ......................................................................... 2 Maintaining Your Fireplace's Appearance ........................... 11 Important Information .......................................................... 2 Battery Replacement .......................................................... 11 Installation Warnings ........................................................... 2
Summary of the content on the page No. 4
Gas 4 Safety Precautions IF YOU SMELL GAS: * Do not light any appliance * Extinguish any open flame * Do not touch any electrical switch or plug or unplug anything * Open windows and vacate building * Call gas supplier from neighbor's house, if not reached, call fire department This unit must be installed by a qualified installer to prevent the possibility of an explosion. Your dealer will know the requirements in your area and can inform you of those people considered qualified.
Summary of the content on the page No. 5
Safety Precautions 5 Do not place clothing or other Light the heater using the built-in flammable items on or near the igniter. Do not use matches or heater. Because this heater can any other external device to light be controlled by a thermostat your heater. there is a possibility of the heater turning on and igniting any items placed on or near it. Allow the heater to cool before carrying out any maintenance or cleaning. The viewing glass should be opened only f
Summary of the content on the page No. 6
6 Operation Before You Begin • Read this entire manual before you use your new fireplace (especially the section "Safety Precautions" on pages 4 & 5). Failure to follow the instructions may result in property damage, bodily injury, or even death. Location of Controls Swing the concelament cover up and slide it back to expose An instruction card for operating the controls. Lift up and swing the lower grill the fireplace is attached to the inside of the fireplace here. down to acces
Summary of the content on the page No. 7
Operation 7 Starting the Fireplace for the First Time • Burn the heater at a high setting with the blower off for an extended period (up to 48 hours). This will cure the painted surfaces. Fumes from the paint curing and oil burning off the steel will occur. This is normal. We recommend opening a window to vent the room. • Condensation may appear on the glass each time you start the fireplace - this is normal. • Blue Flames will occur on the fireplace when it first comes on. After
Summary of the content on the page No. 8
FLAME ADJUST HIGH LOW 8 Operation Adjusting the Flame Height This fireplace has an adjustable flame to tailor the look and heat output to your specific needs. It is adjusted by turning the flame adjust knob. Accent Light This fireplace has a built-in accent light that may be turned on and off and dimmed to your preference. Turn the knob to achieve the desired light output. HIGH OFF LOW ACCENT LIGHT LOW HIGH OFF © Travis Industries 4081205 100-01211_000
Summary of the content on the page No. 9
Operation 9 Adjusting the Optional Blower Speed The blower helps transfer heat from the heater into the room. It will not turn on until the heater is up to temperature (approximately 15 minutes after starting). See the illustration below for instructions on adjusting the blower speed. NOTE: With the rear burner off (comfort control), the heater may not become hot enough for the blower to turn on. HIGH OFF LOW BLOWER Continuous Pilot / GreenSmart™ Pilot Switch This fireplace may run
Summary of the content on the page No. 10
10 Operation Normal Operating Sounds The appliance may creak with change of temperature -- THIS IS NORMAL. Blower Snap Disk This part can produce a Blowers clicking sound as it turns This heater has optional blowers to push the blower on and off. heated air into the room. You will hear the sound of air movement that increases as the speed is increased. Gas Control Valve Extinction Pops As the gas control valve is turned It is not unusual, especially on Propane on and off you will
Summary of the content on the page No. 11
9v Battery AA Battery AA Battery AA Battery AA Battery Maintenance 11 Maintaining Your Fireplace's Appearance Fingerprints or other marks left on the optional plated surface may become etched in place if they are not wiped clean prior to turning the fireplace on. Clean the plated surface with denatured alcohol and a soft cloth (with the fireplace cool). Other cleaners may leave a film that may become etched into the surface. Battery Replacement Power Backup Batteries Four AA batteries
Summary of the content on the page No. 12
12 Maintenance Accent Light Replacement Two accent lights are included in your fireplace to provide additional lighting. These bulbs will burn out over time. To replace, follow the directions below: • Shut off gas to the fireplace and let it cool for 15 minutes. • Remove the glass (see page 15) and logs (see page 17). • Replace the halogen bulbs with the following bulbs: (NOTE: .Take care to not touch the bulb with your fingers – use foam packing or paper towel to hold the bulb): 35
Summary of the content on the page No. 13
Maintenance 13 Grill Installation and Removal Follow the directions below to install. Upper Grill Installation (FPX and Avalon) Hold the grill at an angle and insert the Swing the grill upwards to engage the upper slot. You lower slot over the lower bushing on will need to lift the grill slightly to get it over the bushing. the fireplace (both sides) Once in place the grill is held in place by gravity. Upper Grill Installation (Lopi) NOTE: The upper grill is difficult to install the firs
Summary of the content on the page No. 14
14 Maintenance Face Installation and Removal Some fireplaces have a face that fits over the glass frame. The face can be removed following the directions below. Phillips Screwdriver Four screws hold the face in place. The screws are accessed through the grills on the face. © Travis Industries 4081205 100-01211_000
Summary of the content on the page No. 15
Maintenance 15 Glass Frame Removal and Installation Warning: The appliance must be completely cool before removing the glass. Warning: Do not strike or slam the glass. Based upon the face being used, either: a (a) swing the access door down and remove the top grill, (b) remove the face (unscrew or lift off - see the instructions included with the face for details). Open the four latches holding the glass frame in place (start with the bottom) - follow the directions shown to the right.
Summary of the content on the page No. 16
16 Maintenance Glass Frame Removal and Installation (continued) The latch can come loose from the latch assembly. This occurs only when it is rotated. Follow the directions below to re-install the latch if it comes loose. Hold the latch at an angle and insert it into the slot on the glass frame anchor. Latch NOTE: this slot may be at a different angle than illustrated. Top of Firebox Glass Frame Anchor Note how the washer on the latch fits behind the flange on the glass frame anchor.
Summary of the content on the page No. 17
Maintenance 17 Log Set Installation Log Set Overview When installed, the logs should appear as shown below. Rear Log Right Twig Left Log Left Twig Right Log © Travis Industries 4081205 100-01211_000
Summary of the content on the page No. 18
18 Maintenance Rear Log Installation The rear log has a flat notch on both sides that center it on the grate. Place the rear log on the grate and slide it all the way back until the log contacts the end- brackets on the grate. © Travis Industries 4081205 100-01211_000
Summary of the content on the page No. 19
Maintenance 19 Right Log Installation The left log has a groove that fits over the grate. Note how the left side of the log rests on the burner but does not cover any burner holes. © Travis Industries 4081205 100-01211_000
Summary of the content on the page No. 20
20 Maintenance Left Log Installation The left log has a groove that fits over the grate. Note how the right side of the log rests on the burner but does not cover any burner holes. © Travis Industries 4081205 100-01211_000
