Summary of the content on the page No. 1
Free-Standing
Fireplaces
RFS22
RFS32
RFS42
Installation Instructions & Homeowner's Manual
WARNING! IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED EXACTLY, A FIRE OR
EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.
FOR YOUR SAFETY
FOR YOUR SAFETY
WHAT TO DO IF YOU SMELL GAS:
DO NOT STORE
• Do not try to light any appliance.
OR USE GASOLINE OR OTHER
• Do not touch any electric switch
FLAMMABLE VAPOURS AND LIQUIDS
• Do not use any phone in your building.
IN THE VICI
Summary of the content on the page No. 2
TABLE OF CONTENTS PLEASE READ THE INSTALLATION & OPERATING INSTRUCTIONS BEFORE USING APPLIANCE. Thank you and congratulations on your purchase of a Majestic fireplace IMPORTANT: Read all instructions and warnings carefully before starting installation. Failure to follow these instructions may result in a possible fire hazard and will void the warranty. Installation Instructions...................................................................................................... 3 Important Cu
Summary of the content on the page No. 3
12" (305mm) INSTALLATION INSTRUCTIONS This gas fireplace should be installed by a qualified installer in IMPORTANT: accordance with local building codes and with current CAN / CGA-B149 (. 1 or .2) Installation codes for Gas Burning PLEASE REVIEW THE FOLLOWING Fireplaces and Equipment. CAREFULLY FOR U.S.A Installations follow local codes and/or the current Remove any plastic from trim parts before turning the National Fuel Gas Code. ANSI Z223.1. fireplace ON. FOR SAFE INSTALLATION AND OPERATION O
Summary of the content on the page No. 4
FIREPLACE DIMENSIONS A K C G I D E J F H B A MODEL RFS22 K D C G E I J F B H MODEL RFS32 A K D M L I C N J H MODEL RFS42 B MODEL RFS22 MODEL RFS32 MODEL RFS42 1/4" A 28 717mm A 26" 660mm A 25" 635mm 1/4" 1/8" B 26" 660mm B 28 717mm B 24 613mm 1/4" 7/8" C 17 454mm C 15 387mm C 16" 406mm 3/4" 1/4" D 19 488mm D 22 578mm D 20" 508mm 5/8" E– – E 18 473mm E 19" 483mm F 21" 533mm F– – F 21" 533mm 1/2" 3/4" G– – G 31 800mm G 31 806mm 3/4" 3/4" 3/4" H 17 451mm H 22 578mm H 17 451mm 5/8" 5/8" 5/8" I 33 85
Summary of the content on the page No. 5
GAS SPECIFICATIONS GAS LINE INSTALLATION MAX. MIN. INPUT INPUT When purging gas line, the front glass must MODEL FUEL GAS CONTROL B.T.U.H B.T.U.H. be removed. RFS22RN Natural Gas Millivolt Hi/Lo 30,000 21,000 The gas pipeline can be brought in through the rear of the RFS22RP Propane Gas Millivolt Hi/Lo 30,000 22,500 fireplace as well as the bottom. Knockouts are provided on RFS22TN Natural Gas Thermostatic 30,000 21,000 the bottom behind the valve to allow for the gas pipe RFS22TP Propane Gas T
Summary of the content on the page No. 6
L I P LO TP TH TPTH PILOT Manifold Gas Outlet OPTIONAL FAN KIT - FK24 Brass Brass Plug Plug STANDARD WITH RFS42 Thermostat Pressure Bulb Regulator Gas Inlet It will be easier to install the fan before Thermocouple connecting the gas line to the fireplace. Inlet Pilot Tube entry 1. Open front access door panel by pulling forward on brass lip. Control 2. Guide the fan through the opening at the back of the Knob Pilot Adjustment Control pedestal, with the outlet pointed up and the fan mounting Knob
Summary of the content on the page No. 7
COMMON FLUE INSTALLATIONS VENTING INSTRUCTIONS CANADIAN INSTALLATIONS: In some areas it is possible to vent more than one gas The venting system must be installed in accordance with fireplace into the same flue. You must ensure that the flue the current CAN/CGA-B149 (.1 or.2) installation code, and being shared has the proper capacity to handle both the authority having jurisdiction. fireplaces. Check installation codes for venting capacity information. U.S.A. INSTALLATIONS: The venting system
Summary of the content on the page No. 8
Retrofitting To An Existing Brick Chimney PROPER VENT PERFORMANCE The CFM Majestic Products Company strongly recommends installing an approved chimney liner in an existing brick chimney. Check Draft Here This will maximize the potential draft of the chimney and lessen the effects of slow chimney start up. This is important because many homes (including older renovated ones) have become much tighter with respect to air exchange (a home breathing). An overly tight home will create conditions that
Summary of the content on the page No. 9
OPERATING INSTRUCTIONS GLASS REMOVAL GENERAL GLASS INFORMATION Only glass approved for use in The CFM RFS22 Majestic Products Company products 1. Remove frame window brass trim (See Trim Removal may be used for replacement. section) 1. The use of substitute glass will void all product 2. Remove remaining bottom 3/8" nut at the bottom of the warranties. frame window. 2. Care must be taken to avoid breakage of the glass. 3. Remove frame window by pulling it forward and up. Under no circumstances s
Summary of the content on the page No. 10
RFS42 GLASS CLEANING 1 .Remove Bay Window assembly and Glass Frame (see "Glass Frame Removal" section). It will be necessary to clean the glass periodically. 2. Remove logs from packaging. During start-up condensation, which is normal, forms on 3. Place rear log (SR4) on rear bracket . Ensure log is the inside of the glass and causes lint, dust and other seated properly, leveled and centered to the unit), so it airborne particles to cling to the glass surface. Also will not move from side to si
Summary of the content on the page No. 11
I O L PILOT OFF L CLEANING PROCEDURE 3/8" - 1/2" 1. Turn off pilot light at gas valve. 2. Remove front glass. 3. Remove logs. CAUTION: LOGS MAY BE HOT Fig. 20 4. Vacuum burner compartment especially around orifice/ SIT VALVE PSE VALVE primary air openings. 5. Reinstall logs. 6. Check pilot and main burner operation. 7. Reinstall front glass. RFS22 8. Recheck pilot and main burner operation. RFS32 9. Check visually the flame pattern and compare with Fig. 21 or 22. Fig. 21 FLAME ADJUSTMENT (RN/RP
Summary of the content on the page No. 12
I P F OF PILOT OFF LIGHTING AND OPERATING INSTRUCTIONS FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. A . This fireplace has a pilot which must be lit manually. C . Use only your hand to push in or turn the gas control When lighting the pilot follow these instructions exactly. knob. Never use tools. If the knob will not push in or turn B . BEFORE LIGHTING smell
Summary of the content on the page No. 13
TROUBLE SHOOTING THE GAS CONTROL SYSTEM SIT 630 GAS VALVE Note: Before trouble shooting the gas control system, be sure external gas shut off is in the "On" position. WARNING: BEFORE DOING ANY GAS CONTROL SERVICE WORK, REMOVE GLASS FRONT. SYMPTOM POSSIBLE CAUSES CORRECTIVE ACTION 1. Spark ignitor will not light A. Defective or misaligned Using a match, light pilot. If pilot lights, turn off pilot and electrode at pilot. push the red button again. If pilot will not light - check gap at elect
Summary of the content on the page No. 14
TROUBLE SHOOTING THE GAS CONTROL SYSTEM SIT NOVA 820 MILLIVOLT VALVE Note: Before trouble shooting the gas control system, be sure external gas shut off is in the "On" position. WARNING: BEFORE DOING ANY GAS CONTROL SERVICE WORK, REMOVE GLASS FRONT. SYMPTOM POSSIBLE CAUSES CORRECTIVE ACTION 1. Spark ignitor will not light A. Defective or misaligned Using a match, light pilot. If pilot lights, turn off pilot and electrode at pilot. push the red button again. If pilot will not light - check g
Summary of the content on the page No. 15
TROUBLE SHOOTING THE GAS CONTROL SYSTEM HONEYWELL MILLIVOLT VALVE START CHECK • GAS SUPPLY ON NO • SUPPLY LINE HOOKED UP • SHUTOFF VALVE OPEN • LOCKOUT HAS ENGAGED. WAIT YES 60 SECONDS AND TRY AGAIN. • FOR SPARK AT ELECTRODE WHILE DEPRESSING PIEZO — 1/8" GAP TO PILOT LIGHTS WITH PILOT HOOD NEEDED. NO PIEZO IGNITOR • ALL WIRING CONNECTIONS • REPLACE PIEZO IGNITOR YES • FOR AIR IN THE LINES • THERMOPILE NEEDS A MINIMUM 325mV. ADJUST PILOT FLAME HEIGHT. • ALL WIRING CONNECTIONS.
Summary of the content on the page No. 16
REPLACEMENT PARTS LIST DESCRIPTION RFS22 RFS32 RFS42 1. Log Set Complete 10000160 10000160 10000205 1a. Log Ember Front KR1 KR1 SR1 1b. Log Front Left KR2 KR2 SR2 1c. Log Front Right KR3 KR3 SR3 1d. Log Rear KR4 KR4 SR4 1e. Log Top Left KR5 KR5 SR5 1f. Log Top Right KR6 KR6 SR6 2. Burner Lava Rock (Package) 57897 57897 57897 3a. Burner with Tiles Nat. 10000198 10000198 10000866 3b. Burner with Tiles Prop. 57904 57904 10000867 4. Ceramic Tile (single) 57803 57803 57803 5a. Orifice Front Nat. SEE
Summary of the content on the page No. 17
OFF O L HI REPLACEMENT PARTS 42 41 39 4 42 11 3a/b 34 18 35 39 43 38 29 43 5/6a/b 15 17 13 44 19 30 9 a/b 7a/b 49 22 33 32 31 10 a/b 23 33 14 36 a/b 37 28 it 25a/b 12 17 26 16 47 39 8 a/b 27 2 48 46 41 42 21a,b OFF 45 24 a/b 20 #1 - COMPLETE LOG SET -- RFS22/RFS32 #1 COMPLETE LOG SET RFS42 43 1d 1d 40 40 1f 1e 1f 1e 39 1c 1b 1b 1c 1a 1a - 17 - PILOT LO ON PILOT ADJ I H PILOT
Summary of the content on the page No. 18
OPTIONS REMOTE CONTROL For units with RN/RP valves MRC1 - On/Off Button Remote Control MRC2 - Temperature Control Remote MRC3 - Temperature Control w/digital display & 24 hour programmable clock IMT - Wall Mounted Thermostat - 18 -
