Summary of the content on the page No. 1
Operating Instruction and Parts Manual ESP45
Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.
Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or
property damage! Retain instructions for future reference.
24-Volt Backup
Sump
Pump
All wiring must be
General Safety
Description
performed by a
qualified electrician.
Inform
Summary of the content on the page No. 2
12V 12V Battery Battery B A Operating Instructions and Parts Manual Battery Information If battery acid CHART 1 - STANDBY POWER contacts your PUMPING CAPACITY The system is designed to operate most eye(s), flush with cold running water efficiently with sealed lead acid (SLA) Amp Hours Total Gallons for 10 minutes and seek immediate Per Battery Pumped* batteries. Deep cycle marine batteries medical attention. If acid contacts your 40.0 11,000 can also be used. skin or clothing, wash immediately
Summary of the content on the page No. 3
ESP45 Pump Installation Installation of this unit may take several hours. Before disabling your Floor main pump, have ready an appropriate Joist means of evacuating the sump. Slope Ridgid Pipe 1. Turn power to main pump off. PVC Down 1 2. Pump must be installed using 1 /4” Pipe 1 or 1 /2” rigid PVC piping. Pump Installation Check Valve The ESP45 can be installed as a back up (See Step 6) PS/BC system with a separate dedicated discharge line (Method 1), or tied into an existing sump pump line
Summary of the content on the page No. 4
Operating Instructions and Parts Manual Pump Installation (Continued) 3. A check valve will be required in Floor the discharge line of BOTH the Joist “Y” Rigid PVC Main AC pump and the ESP45 Connector Pipe pump to prevent recirculation of water into the sump pit. System will 45° not function without two check Elbow valves. Check Valve PS/BC (See Step 10) 1 1 4. Cut a 4’ section of 1 /4" or 1 /2" diameter rigid PVC pipe. Cement 1 1 /2" pipe to a threaded fitting. 1 Cement 1 /4" pipe into pipe 1 c
Summary of the content on the page No. 5
ESP45 CHART 2 - PS/BC STATUS LIGHTS PS/BC Installation LIGHT ON WHEN ACTION REQUIRED (Continued) Red Low Voltage or Blown Fuse Check Fuse or 1. Place battery box within six feet of Replace Batteries the sump and a 115 VAC separately Yellow Battery OK None fused outlet. The outlet must be Green AC power on None protected by a ground fault circuit interrupter (GFCI). The area must also Working in the 1. After installation, the backup pump vicinity of lead acid be clean, dry and well-ventilated. wi
Summary of the content on the page No. 6
Operating Instructions and Parts Manual Maintenance 5. If pump operates normally, plug 4. Unplug the main pump and fill sump (Continued) PS/BC into wall outlet, turn on main with water until back up pump turns pump. If pump fails to operate on. Repeat process two times to be 3. Inspect the terminals and clamps normally, see Troubleshooting guide sure pump is operating normally. for corrosion and tightness. Clean and correct problem. Repeat step 5. and tighten as required. Troubleshooting Chart S
Summary of the content on the page No. 7
ESP45 For Replacement Parts, call 1-800-237-0987 Please provide following information: Address parts correspondence to: -Model number Wayne Water Systems -Serial number (if any) 101 Production Drive -Part descriptions and number as shown in parts list Harrison, OH 45030 U.S.A. 7 2 Ref. Part 1 6 No. Description Number Qty. 1 Pump 06710 1 2 PS/BC (power supply/ battery charger) 30260-001 1 3 Impeller assembly 29884-001 1 5 4 Wear ring 28183-001 1 5 Impeller plate 15958 1 6 Seal 21203-001 1 *7 Floa
Summary of the content on the page No. 8
Operating Instructions and Parts Manual Limited Warranty For three years from the date of purchase, Wayne Water Systems (“Wayne”) will repair or replace, at its option, for the original purchaser any part or parts of its Sump Pumps or Water Pumps (“Product”) found upon examination by Wayne to be defective in materials or workmanship. Please call Wayne (800-237-0987) for instructions or see your dealer. Be prepared to provide the model and serial number when exercising this warranty. All transpor
