Summary of the content on the page No. 1
GPX 165
Owner’s Manual
Gas Piston Pump
Do not use this equipment before reading this manual!
Model Numbers:
Bare 0509009
Complete 0509039
Bare w/5 Gal. Siphon 0509055
Complete w/5 Gal. SIphon 0509059
SprayTECH
1770 Fernbrook Lane
Minneapolis, MN 55447
Technical Assistance: 1-800-292-4637
Order Entry: 1-800-443-4500
Fax: 1-800-525-9501
NOTE: This manual contains important warnings and
instructions. Please read and retain for reference.
www.spraytechinc.com
Printed in the U. S. A. 0306 © 20
Summary of the content on the page No. 2
Summary of the content on the page No. 3
3. Always use the nozzle tip guard. Do not spray without 12. Before each use, check all hoses for cuts, leaks, the nozzle tip guard in place. abrasion or bulging of cover. Check for damage or movement of couplings. Immediately replace hose if 4. Only use a nozzle tip specified by the manufacturer. any of those conditions exist. Never repair a paint hose. 5. Use caution when cleaning and changing nozzle tips. Replace with a conductive high-pressure hose. In the case where the nozzle tip clogs
Summary of the content on the page No. 4
Summary of the content on the page No. 5
Summary of the content on the page No. 6
Summary of the content on the page No. 7
Summary of the content on the page No. 8
Summary of the content on the page No. 9
Summary of the content on the page No. 10
Summary of the content on the page No. 11
Summary of the content on the page No. 12
Summary of the content on the page No. 13
Summary of the content on the page No. 14
5. Line up the four holes around the outside of the clutch 6. Make sure that there is a white Teflon o-ring on the end of field with the four set screw holes in the gear housing. the transducer that gets inserted into the filter housing. The clutch field wires should be at approximately the 1 or Insert the transducer into the filter housing port. 2 o’clock position. 7. Hold the transducer tube with a pliers to prevent it from 6. Route the two clutch field wires through the grommet and rotating
Summary of the content on the page No. 15
Summary of the content on the page No. 16
Summary of the content on the page No. 17
Troubleshooting Problem Cause Solution The unit will not run. 1. The pressure is set too low. 1. Turn the pressure control knob clockwise to supply power to the unit and increase the pressure setting. 2. Faulty or loose wiring. 2. Inspect or take to a SprayTECH authorized service center. 3. The gas tank is empty. 3. Fill the gas tank. The unit will not prime. 1. The PRIME/SPRAY valve is in the 1. Rotate the PRIME/SPRAY valve clockwise SPRAY position. to the PRIME position. 2. Air leak in the sip
Summary of the content on the page No. 18
7. N’utilisez pas de peinture ou de solvant contenant du Consignes de sécurité halon, par exemple, le chlore, les agents antimoisissure à Le présent manuel comprend des renseignements devant être l’eau de Javel, le chlorure de méthylène et le lus attentivement avant toute utilisation de l'appareil. Lorsque trichloroéthane. Ils ne sont pas compatibles avec l'un des symboles suivants apparaît, il est recommandé d'être l’aluminium. Contactez le fournisseur de revêtements pour particulièrement atte
Summary of the content on the page No. 19
Summary of the content on the page No. 20
8. Mantenga la zona de pulverización bien ventilada. Precauciones de seguridad Asegúrese de que circula aire fresco por la zona para Este manual contiene información que debe leer y comprender evitar que se acumulen vapores inflamables en el aire antes de usar el equipo. Cuando se encuentre con uno de los de la zona de pulverización. Ponga el conjunto de la siguientes símbolos, asegúrese de observar sus indicaciones bomba en una zona bien ventilada. No pulverice el de seguridad. conjunto de la b
