Summary of the content on the page No. 1
English Español
For Your Records and
Warranty Assistance
T T Type 2 Models ype 2 Models ype 2 Models
For reference, also attach your receipt or a copy
of your receipt to the manual.
Owner’s Guide and Installation Manual
__________________________________________
Model Name
__________________________________________
Model No.
__________________________________________
Date Purchased
__________________________________________
Where Purchased
Form# 42609-01
20090908
©2009 Hunter Fan Co.
Summary of the content on the page No. 2
Welcome Your new Hunter ceiling fan is an addition to your home or office that ® will provide comfort and performance for many years. This installation and operation manual gives you complete instructions for installing and operating your fan. We are proud of our work. We appreciate the opportunity to supply you with the best ceiling fan available anywhere in the world. Before installing your fan, for your records and warranty assistance, record information from the carton and Hunter namepl
Summary of the content on the page No. 3
Installer’s Choice and Optional Accessories Understanding Mounting and Installer’s Choice® Hunter’s patented 3-position mounting system provides you maximum installation flexibility and ease. You can install your Hunter fan in one of three ways, depending on ceiling height and your preference: Low Profile, Standard, or Angle mounting. The steps in this manual include instructions for all three Installer’s Choice mounting methods. Low Profile Mounting fits close to the ceiling, recommended f
Summary of the content on the page No. 4
1 • Getting Ready To install a ceiling fan, be sure you can do the following: • Locate the ceiling joist or other suitable support in ceiling. • Drill holes for and install wood screws. • Identify and connect electrical wires. • Lift 40 pounds. If you need help installing the fan, your Hunter fan dealer can direct you to a licensed installer or electrician. Gathering the Tools You will need the following tools for installing the fan: • Electric drill with 9/64” bit • Standard screwdriver (magne
Summary of the content on the page No. 5
2 • Installing the Ceiling Plate CAUTION: To avoid possible electrical shock, before installing your fan, Towards disconnect the power by turning off the circuit breakers to the outlet box Ceiling Peak and associated wall switch location. If you cannot lock the circuit breakers in the off position, securely fasten a prominent warning device, such as a tag, to the service panel. 2-1. Drill two pilot holes into the wood support structure through the outermost holes in the outlet box. The p
Summary of the content on the page No. 6
3 • Assembling the Fan WARNING: Fan may fall if not assembled as directed in these Standard or Angle Mounting installation instructions. Steps 3-2 – 3-3 3-1. Unbundle the wires from the fan. For Standard or Angle mounting: Downrod 3-2. Insert the downrod through the canopy and canopy trim ring. Feed the wires from the fan through the downrod on one side of the pin in the ball. Canopy 3-3. Loosen the square head set screw on the adapter to install the pipe and ball assembly. Note: Wh
Summary of the content on the page No. 7
4 • Hanging and Wiring the Fan 4-1. Raise the fan and align the slots in the canopy with the hooks on the ceiling plate. Note: To hang the fan, you must tilt the canopy to an almost vertical Wire position so that the canopy slots sit on the ceiling plate hooks. Connector All wiring must be in accordance with national and local electrical codes and ANSI/NFPA 70. If you are unfamiliar with wiring, use a qualified electrician. Wall switches are not included. Select an acceptable general-us
Summary of the content on the page No. 8
5 • Installing the Canopy and Canopy Trim Ring WARNING: Failure to complete the following steps could cause the fan Step 5-1 to fall. Note: It is recommended you use a magnetic tip screwdriver for the following steps. Tab 5-1. Rotate the hanger ball so the tab in the canopy is secure in the hanger ball groove. Note: Your fan may have multiple tabs and Groove grooves that must be aligned. 5-2. Swing the fan up to align the canopy screw holes with the mounting holes on the ceiling plate.
Summary of the content on the page No. 9
6 • Assembling the Blades Hunter fans use several styles of fan blade irons (brackets that hold the blade to the fan). 6-1. Your fan may include blade grommets. If your fan has grommets, Step 6-1 (Detail) insert them by hand into the holes on the blades. 6-2. Attach each blade to a blade iron using three blade assembly screws. If you used grommets, the blades may appear slightly loose after screws are tightened. This is normal. 6-3. Some blade mounting screws are installed in the motor to s
Summary of the content on the page No. 10
7 • Completing Your Installation With or Without a Light Fixture 7-1. To attach the upper switch housing, partially install two #6-32 x 3/8” housing assembly screws into the switch housing mounting plate. 7-2. Feed the upper plug connector through the center opening of the housing. 7-3. Align the keyhole slots in the housing with the housing assembly screws. 7-4. Turn the housing counterclockwise until the housing assembly screws are firmly situated in the narrow end of the keyhole slots.
Summary of the content on the page No. 11
7 • Completing Your Installation With or Without a Light Fixture (continued) Note: If you do not want to install the light fixture, see “Uninstalling the Light Fixture” on page 12. 7-5. To attach the lower switch housing, connect the upper plug connector from the motor to the lower plug connector in the lower switch housing assembly. Note: Both plug connectors are polarized and will only fit together one way. Make sure the connectors are properly aligned before connecting them. Incorrect
Summary of the content on the page No. 12
7 • Completing Your Installation With or Without a Light Fixture (continued) Uninstalling the Light Fixture 1. Loosen and remove the three screws that attach the light kit Step 1 to the light kit mounting plate. Lower Switch 2. Uninstall the nut inside the lower switch housing. Housing 3. Disconnect the plug connectors between the black wire and Light Kit the black/white wire. 4. Disconnect the plug connectors between the two white wires. 5. Remove the two light kit assembly screws. 6. Unscr
Summary of the content on the page No. 13
8 • Operating and Cleaning Your Ceiling Fan 8-1. Turn on electrical power to the fan. 8-2. The fan pull chain controls power to the fan. The pull chain has four settings in sequence: High, Medium, Low and Off. • Pull the chain slowly to change settings. • Release slowly to prevent the chain from recoiling into the blades. • The chain uses a breakaway connector that separates if the chain is jerked. If this happens, simply reinsert the chain into the connector. 8-3. The light pull chain contr
Summary of the content on the page No. 14
9 • Troubleshooting Problem: Nothing happens; fan does not move. 1. Turn power on, replace fuse, or reset breaker. 2. Loosen canopy, check all connections according to the wiring the fan section. 3. Check the plug connection in the switch housing. 4. Push motor reversing switch firmly left or right to ensure that the switch is engaged. 5. Pull the pull chain to ensure it is on. 6. Remove the shipping bumpers. Problem: Noisy operation. 1. Tighten the blade bracket screws until snug. 2. Tighten
