Summary of the content on the page No. 1
BFLH70L, BFLH85L
e Heater/Exhaust Fan/Light User’s Guide
Item Stock Number(s): BFLH70L, BFLH85L
IMPORTANT INSTRUCTIONS -
a
OPERATING MANUAL
READ AND SAVE THESE INSTRUCTIONS
READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN THE PRODUCT DESCRIBED.
PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION. FAILURE TO COMPLY WITH
INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE!
RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.
GENERAL SAFETY INFORMATION
Whe
Summary of the content on the page No. 2
2. Remove the two machine screws holding the light GENERAL SAFETY INFORMATION reflector in place. Keep the reflector and screws in (Continued) the carton until needed so they do not get damaged fuel burning equipment to prevent back drafting. Follow or lost. (Figure 1). the heating equipment manufacturer’s guideline and safety standards such as those published by the National Fire Protection Association (NFPA) and the American Society for Heating, Refrigeration, and Air Conditioning Engineers (A
Summary of the content on the page No. 3
ceiling. Secure the ends of the rails with screws or 1a. Mounting Tab Installation: Position housing against nails (not included) to the joists and slide housing the joist and trace an outline of the housing onto the into final position (Figure 4). ceiling material (Figure 7). Set housing aside and cut opening, being careful not to cut or damage any electrical or other hidden utilities. Place housing next to the joist and insure that it is flush with the finished ceiling. Secure with screws or n
Summary of the content on the page No. 4
1. Run wiring from approved wall switches carrying SECTION 6 the appropriate rating. One neutral (white), one Completing the Installation ground (green or bare copper), and three hot (black, 1. Insert the plug from the heating unit into the red, blue leads connected to the switch, one for receptacle marked “HEAT”, and the plug from the each function). Secure the electrical wires to the fan into the receptacle marked “VENT”(Figure 11). housing with an approved electrical connector. Make sure you
Summary of the content on the page No. 5
4. Attach light reflector in place with the two screws SECTION 7 removed during Step 2 in SECTION 1 Preparing the Use and Care Unit so grill fits snuggly against ceiling (Figure 14). CAUTION: MAKE SURE POWER IS SWITCHED OFF AT SERVICE PANEL BEFORE SERVICING THE UNIT. 1. Cleaning the Grill: Reverse the instructions in Section 6 Completing the Installation to remove grill. Use a mild detergent, such as dishwashing liquid, and dry Screws with a soft cloth. NEVER USE ANY ABRASIVE PADS OR SCOURING PO
Summary of the content on the page No. 6
WARRANTY WHAT IS COVERED? WHAT IS NOT COVERED? • Installation services or service trips to your home to teach Full Five Year Parts Warranty from date of original proof of you how to use the product. purchase. We will provide, free of charge, a replacement part that fails due to manufacturing defect in material or workmanship, • Labor costs or the cost of replacement components as part when installed and used as directed in the User’s Guide. of routine maintenance. This warranty is extended to th
Summary of the content on the page No. 7
REPLACEMENT PARTS DIAGRAM 2 4 5 1 3 2 2 6 24 30 29 7 8 10 13 12 26 11 2 16 25 9 12 27 14 13 15 15 28 17 19 20 21 22 18 23 # Qty. Description Replacement Part # # Qty. Description Replacement Part # 1 1 Fan Housing 5S3402039 16 1 Wire Compartment 5S3402052 2 4 Mounting Rails 5S1299002 17 3 Receptacle 5S3402053 3 2 Collar Screw 5S3402040 18 1 Lamp Holder 5S3402054 4 1 Collar 5S3402041 19 1 Reflector 5S3402055 5 1 Damper 5S3402042 20 1 Grill 5S3402056 6 1 Motor - Vent 5S3402043 21 1 Lens Frame 5S34
Summary of the content on the page No. 8
210572111 Rev. B 5-06 8 of 8 www.geelectrical.com
