Summary of the content on the page No. 1
READ AND SAVE THESE INSTRUCTIONS
®
60” Industrial
Heat Fan
Model No.
Owner's Manual
HF1160BK 00
Net Weight: 19.8 Lbs. HF1160WW 00
LIMITED WARRANTY
What The Warranty Covers:
This warranty covers the motor and the other components and accessories of your Emerson ceiling fan against all defects in workmanship and materials.
You must be the original purchaser or user of the product to be covered.
What The Period Of Coverage Is:
As it applies to the motor, this warranty will last for five years from
Summary of the content on the page No. 2
! WARNING WARNING: To avoid fire, shock, and serious personal injury, follow these instructions. Safety Instructions 1. Read your owner’s manual carefully and keep it for future reference. 2. Before servicing or cleaning unit, switch power off at service panel and lock service panel disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a warning device, such as a tag, to the service panel. 3. Be careful of
Summary of the content on the page No. 3
Checking Contents of Package Electrical Requirements 1. Unpack the items carefully to avoid damage to any Your new ceiling fan will require a grounded electrical of the components. supply line of 120 volts AC, 60 Hz, 15 amp circuit. Check to see that you have received the following The outlet box must be securely anchored and parts: capable of withstanding a load of at least 50 pounds. NOTE: If you are uncertain of part description, refer to the exploded view illustration. ! WARNING a. Fan motor
Summary of the content on the page No. 4
2. Using the setscrew wrench (supplied), remove the ! WARNING two setscrews from the top of the motor yoke (Figure 1). Retain the setscrews for future use. It is critical that the clevis pin in the motor coupling is properly installed and the setscrews securely 3. Route the three 48” motor leads and the safety tightened. Failure to verify that the pin and setscrews cable through the center hole in the motor cover. are properly installed (as shown in Figure 3) could Align the two holes in the mot
Summary of the content on the page No. 5
11. Connect the green grounding wire from the OUTLET hanger ball, the green grounding wire from BOX the hanger bracket, and the green grounding wire from the fan to the grounding conductor of the supply (this may be a bare wire or wire with green TWO SCREWS colored insulation). Securely connect wires with SUPPLIED WITH HANGER OUTLET BOX wire connectors (supplied) (Figure 8). BRACKET WHITE BLACK TAB SUPPLY SUPPLY Figure 5 (NEUTRAL) (HOT) BLACK FAN WIRE WHITE 9. Screw the eye screw (supplied) i
Summary of the content on the page No. 6
Maintenance SAFETY CABLE IMPORTANT CARE INSTRUCTIONS for your Ceiling Fan CEILING COVER Periodic cleaning of your new ceiling fan is the only maintenance that is needed. When cleaning, use only a soft brush or lint free cloth THREADED to avoid scratching the finish. STUDS (2) Abrasive cleaning agents are not required and should #8 LOCKWASHER be avoided to prevent damage to finish. KNURLED KNOB Figure 9 ! WARNING Do not use water when cleaning your ceiling fan. It ! WARNING could damage the moto
Summary of the content on the page No. 7
Repair Parts Listing Part Numbers Key Model No. Model No. No. Description HF1160BK 00 HF1160WW 00 * Hanger Ball Assembly, 760750-46 760750-47 Consisting of: 1 Hanger Bracket — — 2 Hanger Ball — — 3 Downrod — — * Parts Bag Containing: 762499 762499 4 Wire Connector (3) — — 5 Pin, Clevis — — 6 Clip, Hairpin — — 7 Nut, Knurled, 8-32 (2) — — 8 Lockwasher, External Tooth, #8 (2) — — 9 Stud, Threaded, 8-32 x .75” (2) — — 10 Screw, Phillips Hex Head, M6-1.0 x 12mm (7) — — 11 Lockwasher, Split (7) — — 1
Summary of the content on the page No. 8
THIS SIDE UP Repair Parts 3 1 2 9 15 4 18 16 8 17 13 7 14 19 10 11 12 6 5 22 21 20 Air Comfort Products DIVISION OF EMERSON COMPANY 8100 W. Florissant ¥ St. Louis, MO 63136 Part No. F40BP72720000 Printed in Taiwan 02/04 Form No. BP7272
