Summary of the content on the page No. 1
BP7311 48 56" Heat Fans 1/16/08 10:52 AM Page 1
READ AND SAVE THESE INSTRUCTIONS
10' MIN.
TO FLOOR
48” & 56”
Industrial Heat Fans SPECIFICATIONS
Owner's Manual
Model No. Power Amps Watts RPM
HF948BS 1
Model Numbers
120V/60Hz 0.62 72 300
HF948W 1
HF948BS 1 HF956BK 1
HF956BK 1
HF956BS 1 120V/60Hz 0.82 98 280
HF948W 1 HF956BS 1
HF956W 1
HF956W 1
HF948 Net Weight: 18.7 Lbs. HF956 Net Weight: 22.2 Lbs.
LIMITED WARRANTY
What The Warranty Covers:
This warranty covers the motor and the other comp
Summary of the content on the page No. 2
BP7311 48 56" Heat Fans 1/16/08 10:52 AM Page 2 ! WARNING ARNING: W To avoid fire, shock, and serious personal injury, follow these instructions. Safety Instructions 1. Read your owner’s manual carefully and keep it for future reference. 2. Before servicing or cleaning unit, switch power off at service panel and lock service panel disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a warning device, s
Summary of the content on the page No. 3
BP7311 48 56" Heat Fans 1/16/08 10:52 AM Page 3 Checking Contents of Electrical Requirements Package Your new ceiling fan will require a grounded electrical supply line of 120 volts Before discarding packaging material, AC, 60 Hz, 15 amp circuit. be certain all parts have been removed. The outlet box must be securely anchored 1. Unpack the items carefully to avoid and capable of withstanding a load of at damage to any of the components. least 50 pounds. 2. Make certain you receive the followi
Summary of the content on the page No. 4
BP7311 48 56" Heat Fans 1/16/08 10:52 AM Page 4 ! WARNING RETENTION It is critical that the clevis pin in the motor MOTOR WIRE (3) CABLE (1) RUBBER coupling is properly installed and the GROMMET setscrews securely tightened. Failure to HANGER PIPE verify that the pin and setscrews are ASSEMBLY HAIRPIN properly installed (as shown in Figure 3) CLIP could result in the fan falling. CLEVIS PIN MOTOR YOKE 5. Slide the lower canopy down the CANOPIES NOT SHOWN FOR hanger pipe and securely tighten
Summary of the content on the page No. 5
BP7311 48 56" Heat Fans 1/16/08 10:52 AM Page 5 1. Attach the appropriate J-hook to the Hanging Your Heat Fan building structure member. On Steel Beam - Locate and drill a ! WARNING 13/32” diameter hole in the beam. (See Figure 5.) Use a flat washer, lock Turning off wall switch is not sufficient. To avoid possible electrical shock, be washer and nut on both sides of the sure electricity is turned off at the main beam. Position the J-hook so that the fuse box before wiring. All wiring must be
Summary of the content on the page No. 6
BP7311 48 56" Heat Fans 1/16/08 10:52 AM Page 6 2. Lift the fan onto the J-hook and position Wiring Your Heat Fan as shown in Figure 7. Make sure the motor wires and retention cable at the ! WARNING top of the hanger pipe are positioned behind J-hook as illustrated in Figure 7. To avoid possible fire or electrical shock, CAUTION: The electrical wires and do not pinch wires between the hanger ball/downrod assembly and hanger retention cable must not be placed bracket. between the rubber roller
Summary of the content on the page No. 7
BP7311 48 56" Heat Fans 1/16/08 10:52 AM Page 7 Maintenance ! WARNING Check to see that all connections are ! WARNING tight, including ground, and that no bare To avoid possible electrical shock, be wire is visible at the wire connectors, sure electricity is turned off at the main except for the ground wire. service box before servicing. CAUTION:Do not operate fan until blades are in place. Noise and fan damage could result. LUBRICATION - All bearings are permanently lubricated and do not req
Summary of the content on the page No. 8
BP7311 48 56" Heat Fans 1/16/08 10:52 AM Page 8 Repair Parts Listing Part Numbers Key Model No. Model No. Model No. Model No. Model No. No. Description HF948BS 1 HF948W 1 HF956BK 1 HF956BS 1 HF956W 1 1 J-Hook Bag Assembly: 761385 761385 761385 761385 761385 J-Hooks (2 each) — — — — — Hardware (2 each) — — — — — 2 Hanger Assembly 761339 761339 761339 761339 761339 3 Pipe Nipple (8”) 761387-5 761387-2 — — 4 Pipe Nipple (22”) 761387-6 761387 761387-4 761387-7 761387 5 Upper Canopy 761335-BS 7613
