Summary of the content on the page No. 1
READ AND SAVE THESE INSTRUCTIONS
60” Industrial
Model No.
Heat Fan
Owner's Manual
HF1160BK 00
HF1160BS 00
Net Weight: 19.8 Lbs.
HF1160WW 00
LIMITED WARRANTY
What The Warranty Covers:
This warranty covers the motor and the other components and accessories of your Emerson ceiling fan against all defects in workmanship and materials.
You must be the original purchaser or user of the product to be covered.
What The Period Of Coverage Is:
As it applies to the motor, this warranty will last for five
Summary of the content on the page No. 2
! WARNING WARNING: To avoid fire, shock, and serious personal injury, follow these instructions. Safety Instructions 1. Read your owner’s manual carefully and keep it for future reference. 2. Before servicing or cleaning unit, switch power off at service panel and lock service panel disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a warning device, such as a tag, to the service panel. 3. Be careful of
Summary of the content on the page No. 3
Electrical Requirements Your new ceiling fan will require a grounded electrical supply line of 120 volts AC, 60 Hz, 15 amp circuit. The outlet box must be securely anchored and capable of withstanding a load of at least 50 pounds. ! WARNING To reduce the risk of fire, electric shock, or personal injury, mount fan to outlet box marked “Acceptable for Fan Support of 50 lbs. or less”, and use screws supplied with outlet box. Most outlet boxes commonly used for support of light fixtures are not acce
Summary of the content on the page No. 4
2. Using the setscrew wrench (supplied), remove the ! WARNING two setscrews from the top of the motor yoke (Figure 1). Retain the setscrews for future use. It is critical that the clevis pin in the motor coupling is properly installed and the setscrews securely 3. Route the three 48” motor leads and the safety tightened. Failure to verify that the pin and setscrews cable through the center hole in the motor cover. are properly installed (as shown in Figure 3) could Align the two holes in the mot
Summary of the content on the page No. 5
11. Connect the green grounding wire from the hanger ball, the green grounding wire from OUTLET BOX the hanger bracket, and the green grounding wire from the fan to the grounding conductor of the supply (this may be a bare wire or wire with green TWO SCREWS colored insulation). Securely connect wires with SUPPLIED WITH HANGER OUTLET BOX wire connectors (supplied) (Figure 8). BRACKET WHITE BLACK TAB SUPPLY SUPPLY Figure 5 (NEUTRAL) (HOT) BLACK FAN WIRE WHITE 9. Screw the eye screw (supplied) i
Summary of the content on the page No. 6
Maintenance SAFETY CABLE IMPORTANT CARE INSTRUCTIONS for your Ceiling Fan CEILING COVER Periodic cleaning of your new ceiling fan is the only maintenance that is needed. When cleaning, use only a soft brush or lint free cloth THREADED to avoid scratching the finish. STUDS (2) Abrasive cleaning agents are not required and should #8 LOCKWASHER be avoided to prevent damage to finish. KNURLED KNOB Figure 9 ! WARNING Do not use water when cleaning your ceiling fan. It ! WARNING could damage the moto
Summary of the content on the page No. 7
Repair Parts Listing Part Numbers Key Model No. Model No. Model No. No. Description HF1160BK 00 HF1160BS 00 HF1160WW 00 * Hanger Ball Assembly, 760750-46 761655-27 760750-47 Consisting of: 1 Hanger Bracket — — — 2 Hanger Ball — — — 3 Downrod — — — * Parts Bag Containing: 762499 762499 762499 4 Wire Connector (3) — — — 5 Pin, Clevis — — — 6 Clip, Hairpin — — — 7 Nut, Knurled, 8-32 (2) — — — 8 Lockwasher, External Tooth, #8 (2) — — — 9 Stud, Threaded, 8-32 x .75” (2) — — — 10 Screw, Phillips Hex H
Summary of the content on the page No. 8
THIS SIDE UP s t 3 1 2 9 15 4 18 16 8 17 13 7 14 19 10 11 12 6 5 22 21 20 Air Comfort Products DIVISION OF EMERSON ELECTRIC CO. 8100 W. Florissant • St. Louis, MO 63136 Part No. F40BP72720001 Printed in China 01/08 Form No. BP7272-1 U.L. Model No.: HF1160 Repair Par
