Summary of the content on the page No. 1
1
1
1
1 -1
Summary of the content on the page No. 2
YL
Summary of the content on the page No. 3
Supplied Two 60-watt candelabra bulbs l.
Summary of the content on the page No. 4
k l
Summary of the content on the page No. 5
Electrical Requirements Ceiling Fan Procedures IMPORTANT: Your ceiling fan will not General function properly, and may be Your Emerson ceiling fan comes supplied damaged, if used with any wall dimmer with a Fan/Light Wall Control which switch or control other than the consists of a wall control (transmitter) and Emerson Electric Fan/Light Wall a remote control receiver mounted under Control supplied with the fan, or an the ceiling cover. This system allows you optional Emerson Electric SR100 to
Summary of the content on the page No. 6
1. Remove the hanger ball by loosening the setscrew in the hanger ball until the ball falls freely down the downrod (Figure 1). Remove the clevis pin from the downrod, then remove the hanger ball. Retain the pin and hanger ball for DOWNROD DOWNROD reinstallation in step 5. HAIRPIN HAIRPIN CLIP CLIP PIN SETSCREW SETSCREW (2) HANGER BALL CLEVIS PIN CLEVIS PIN MOTOR COUPLING MOTOR DOWNROD COUPLING SETSCREW Figure 2 3. While pulling up on the downrod, Figure 1 securely tighten the two setscrews in t
Summary of the content on the page No. 7
Summary of the content on the page No. 8
Summary of the content on the page No. 9
How to Wire ! WARNING Your Ceiling Fan Hanger bracket must seat firmly against outlet box. If the outlet box is recessed, If you feel that you do not have enough remove wall board until bracket contacts electrical wiring knowledge or box. If bracket and/or outlet box are not experience, have your fan installed by a securely attached, the fan could wobble or fall. licensed electrician. ! WARNING OUTLET Turning off wall switch is not sufficient. BOX To avoid possible electrical shock, be TWO SCRE
Summary of the content on the page No. 10
N N I AC IN L AC e. Securely connect the fan motor black ! WARNING wire to the receiver red (TO MOTOR L) wire. Check to see that all connections are f. Securely connect the fan motor blue tight, including ground, and that no bare wire to the receiver blue (FOR wire is visible at the wire connectors, except for the ground wire. Do not LIGHT) wire. operate fan until blades are in place. Noise and fan damage could result. SUPPLY WHITE WIRE RECEIVER WHITE (NEUTRAL) WIRE RECEIVER BLACK WIRE SUPPLY
Summary of the content on the page No. 11
Summary of the content on the page No. 12
LOAD BLACK Setting Operating Installation of Wall Frequency of Wall Control Control and Receiver SINGLE-POLE INSTALLATION (Figure 18) (Figure 19) Your wall control and receiver have code FAN/LIGHT HOT BLK WALL CONTROL HI switches which must be set in one of 16 LIGHT MED LOW possible code combinations. The four FAN OFF ® BLACK EMERSON OFF ON levers (numbered 1, 2, 3, and 4) on the switches are factory-set in the ON (up) position. Change the switch settings as follows: NEUTRAL GROUND 1. Slide the
Summary of the content on the page No. 13
T T O O 1 2 0 V A C L S O O 7. Refer to page 5 and complete the 5. Connect one black wire of the wall control to both remaining traveler wires ceiling fan installation. in the wall box and secure with wire connector supplied. NOTE: Retrofit 3-way installations are likely to include two traveler wires U between the two wall boxes. In new construction, only one traveler wire Is required. FAN/LIGHT 3-WAY WIRlNG DIAGRAM: WALL WALL BOX CONTROL NEW CONSTRUCTION Figure 20 FAN/LIGHT HOT HI HI LIGHT LIGH
Summary of the content on the page No. 14
BLACK BLACK 5. To turn the light on and off, press and STANDARD WIRING FOR EXISTING release the LIGHT button. The light will 3-WAY CONTROL: turn on at the light level previously set EXISTING WALL CONTROL (see step 4). HOT BLK TRAVELER WIRES LOAD BLK HI HI HOT BLK HI LIGHT LIGHT MED MED LIGHT LOW LOW FAN OFF FAN OFF MED ® EMERSON® EMERSON OFF ON OFF ON FAN/LIGHT LOW WALL CONTROL TRAVELER WIRES LOAD FAN OFF Figure 22 ® EMERSON OFF ON Operating Your Ceiling Fan IMPORTANT Fan installation must b
Summary of the content on the page No. 15
Maintenance Accessories IMPORTANT CARE INSTRUCTIONS 1. Downrod Extension Kits (see store or for your Ceiling Fan catalog). 2. Ceiling Fan Controls (see store or Periodic cleaning of your new ceiling fan is catalog). the only maintenance that is needed. 3. Blades (see store or catalog). When cleaning, use only a soft brush or lint free cloth to avoid scratching the finish. ! WARNING Abrasive cleaning agents are not required The use of any other control not and should be avoided to prevent damage
Summary of the content on the page No. 16
Summary of the content on the page No. 17
762670-5 762670-5 762670-5 -1 -1 -1
Summary of the content on the page No. 18
! WARNING: FOR YOUR OWN SAFETY TURN OFF POWER AT FUSE BOX OR CIRCUIT BREAKER BEFORE TROUBLE SHOOTING YOUR FAN. Trouble Shooting TROUBLE PROBABLE CAUSE SUGGESTED REMEDY 1. Fan will not 1. Fuse or circuit breaker 1. Check main and branch start. blown. circuit fuses or circuit breakers. ! WARNING: Make sure main power is turned off. 2. Loose power line 2. Check line power connections connections to the fan. to fan. 3. Fan/Light Wall Control is OFF. 3. Turn ON Fan/Light Wall Control. 4. Code swit
Summary of the content on the page No. 19
LIMITED WARRANTY What The Warranty Covers: This warranty covers the motor and the other components and accessories of your Emerson Electric Co. ceiling fan against all defects in workmanship and materials. You must be the original purchaser or user of the product to be covered. What The Period Of Coverage Is: As it applies to the motor, this warranty will last for 10 years from the date you purchased your ceiling fan. All other components and accessories are covered by this warranty for one year
Summary of the content on the page No. 20
1 -1
