Summary of the content on the page No. 1
E
V
O
T
S
C
S
O
E
M
T
Owner Owners Manual s Manual
Owner Owner Owners Manual s Manual s Manual
Logwood 1261
EPA EXEMPT PER
METHOD 28A
TESTED TO
UL 1482
CAUTION!
Read All Instructions Care-
fully Before Starting The In-
stallation or Operating This
DO NOT USE THIS HEATER
Heater.
IN A MOBILE HOME OR TRAILER
SAVE THIS MANUAL FOR FUTURE REFERENCE
THIS MANUAL WILL HELP YOU TO OBTAIN EFFICIENT, DEPENDABLE SERVICE FROM THE HEATER, AND ENABLE
YOU TO ORDER REPAIR PARTS CORRECTLY. KEEP IN A SAFE PLACE FOR
Summary of the content on the page No. 2
CONGRATULATIONS! You've purchased a heater from North America's oldest manufacturer of wood burning products. By heating with wood you're helping to CONSERVE ENERGY! Wood is our only Renewable Energy Resource. Please do your part to preserve our wood supply. Plant at least one tree each year. Future generations will thank you. Tools and Materials Needed MATERIALS TOOLS 6" Elbow, Collar and Thimble; As Required Pencil (24 gauge min.) 6 Foot Folding Rule or Tape Measure 1/2" Sheet Metal Screws
Summary of the content on the page No. 3
Safety Rules SAFETY NOTICE: If this heater is not properly installed a house fire may result. For your safety, follow the installation directions. Contact local building or fire officials about restrictions and installation inspection requirements in your area. Read these rules and the instructions carefully. 1. Check with local codes. The installation must 9. For further information on using your heater comply with their rulings. Observe closely the safely, obtain a copy of the National Fire Pr
Summary of the content on the page No. 4
MINIMUM CLEARANCE Installation TO COMBUSTIBLE WALLS Place the heater on solid masonry or solid concrete. When the heater is used on a combustible floor, use an Underwrit- ers Listed floor protector. The floor protector must comply 18" 458mm with UL Standards. The base should extend at least 16" beyond the door side of the heater and should extend under the flue pipe if it is elbowed towards a wall. (Fig. 5). (60" MIN.) 1. Uncrate and/or unpack the heater, removing all pack- ing material, being
Summary of the content on the page No. 5
Operation of the Heater FLUE CONNECTION-NON-COMBUSTIBLE WALL 1. BE SURE TO PUT A LAYER OF SAND OR FIREBRICK APPROXIMATELY 1 1/2" THICK IN THE BOTTOM OF THE STOVE BEFORE STARTING FIRE. NONCOMBUSTIBLE WALL 2. Burn wood or wood products only. The wood should be air dried THIMBLE for at least six months prior to use for maximum efficiency. COLLAR 3. After the fire has been started and is burning satisfactorily, PIPE adjust the rate of burning by opening or closing the draft ELBOW damper wheel on the
Summary of the content on the page No. 6
CONNECTION OF CHIMNEY CONNECTOR TO A MASONRY CHIMNEY THROUGH A COMBUSTIBLE WALL Figure 8 shows how to connect the chimney connector of a heater to a masonry chimney through a combustible wall. There are five allowable ways that a chimney connector can be connected to a masonry chimney by passing through a combustible wall. NFPA Standard 211 allows the following wall pass-through systems. FIGURE 8 - CONNECTION OF CHIMNEY CONNECTOR TO A MASONRY CHIMNEY THROUGH A COMBUSTIBLE WALL CEILING SEE PARTS
Summary of the content on the page No. 7
PART A, FIGURE 8 MINIMUM CHIMNEY CLEARANCE TO (FIGURE 8 CONTINUED ON NEXT PAGE) BRICK AND COMBUSTIBLES IS 2 IN. MINIMUM CLEARANCES 12 IN. OF BRICK ALL AROUND CHIMNEY CONNECTOR TO HEATER FIRE CLAY LINER MINIMUM 12 IN. (5/8" MIN. WALL THICKNESS) TO COMBUSTIBLES MASONRY CHIMNEY CONSTRUCTED TO MIN. 3-1/2" THICK BRICK NFPA 211 MASONRY WALL 1. Use a minimum 3-1/2" thick brick masonry wall framed into the combustible wall. A fireclay liner (ASTM C315 or equivalent) having a 5/8" minimum wall thickness
Summary of the content on the page No. 8
AIR SPACE PART B MINIMUM CHIMNEY CLEARANCES FROM MASONRY TO SHEET STEEL SUPPORTS AND COMBUSTIBLES 2 IN. FIGURE 8 - (FIGURE 8 CONTINUED) FACTORY-BUILT MINIMUM CLEARANCE CHIMNEY LENGTH 9 IN. ALL AROUND NONSOLUBLE CHIMNEY CONNECTOR REFACTORY TO HEATER CEMENT CHIMNEY LENGTH FLUSH WITH INSIDE USE CHIMNEY MFRS. PARTS TO OF FLUE AIR SPACE ATTACH CONNECTOR SECURELY 9 IN. MINIMUM SOLID INSULATED, LISTED FACTORY-BUILT CHIMNEY LENGTH MASONRY CHIMNEY CONSTRUCTED SHEET STEEL SUPPORTS TO NFPA 211 (24 GAUGE M
Summary of the content on the page No. 9
WARNING! CAUTION! NEVER STORE FLAMMABLE LIQUIDS, NEVER USE GASOLINE, GASOLINE-TYPE ESPECIALLY GASOLINE. IN THE LANTERN FUEL, KEROSENE, CHARCOAL VICINITY OF THE HEATER. LIGHTER FLUID, OR FLAMMABLE LIQUIDS TO START OR "FRESHEN UP" A FIRE IN THE HEATER. CAUTION! OVERFIRING THE APPLIANCE MAY CAUSE A HOUSE FIRE. IF A UNIT OR CAUTION! CHIMNEY CONNECTOR GLOWS, YOU USE WOOD OR WOOD-LIKE MATERIALS ARE OVERFIRING. ONLY. DO NOT USE COAL OR CHARCOAL. COAL OR CHARCOAL WILL DESTROY THE FIREBOX. DO NOT USE WA
Summary of the content on the page No. 10
Model 1261 15 Repair Parts 13 12 16 10 21 11 22 8 5 19 4 18 17 9 20 1 3 14 2 7 6 KEY PART NO. DESCRIPTION QNTY. 1 40296 REAR LEG 2 2 40318 FRONT LEG 2 3 40297 MAIN BOTTOM 1 4 40298 MAIN SIDE 2 5 40299 MAIN BACK 1 6 40300 HEARTH PLATE 1 7 40301 SLIDING DRAFT PLATE 1 8 40302 DOOR FRAME 1 9 40303 DOOR 1 10 40304 MAIN TOP 1 11 40305 PIVOTING TOP 1 12 40306 LID 2 13 40307 LID SUPPORT 1 14 40308 LID LIFTER 1 15 40332 FLUE COLLAR 1 16 D6 SOLID FLUE DAMPER 1 17 83427 DOOR PINS 2 18 89971 HANDLE 1 19 899
Summary of the content on the page No. 11
NOTES 11
Summary of the content on the page No. 12
HOW TO ORDER REPAIR PARTS THIS MANUAL WILL HELP YOU OBTAIN EFFICIENT, DEPENDABLE SERVICE FROM THE HEATER, AND ENABLE YOU TO ORDER REPAIR PARTS CORRECTLY. KEEP IN A SAFE PLACE FOR FUTURE REFERENCE. WHEN WRITING, ALWAYS GIVE THE FULL MODEL NUMBER WHICH IS ON THE NAMEPLATE ATTACHED TO THE BACK OF THE HEATER. WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE FOLLOWING INFORMATION AS SHOWN IN THIS LIST: 1. The PART NUMBER 2. The PART DESCRIPTION 3. The MODEL NUMBER: 1261 4. The SERIAL NUMBER: UNITED STATES
