Summary of the content on the page No. 1
USERS INFORMATION MANUAL
MODEL TSTATBBP2W01
PROGRAMMABLE DIGITAL
Heating & Cooling Systems
THERMOSTAT
NOTE TO INSTALLER:
This manual must be left with the equipment user.
I2:34
Mo
2 - Wire Operation
No Batteries Required
HEAT
72 Simple, Single Setpoint
72
7 Day Programmable
4 Time Periods
Very Easy to Program
Large, Easy To Read Display
Heat only, or Cool only
Thermoglow Backlight
Locking Keypad
Meets California Title 24 Residential
Summary of the content on the page No. 2
Table Of Contents FRONT PANEL 2 DISPLAY 3 QUICK START Set the clock and go 5 BASIC OPERATION 6 PROGRAMMING Time Periods 8 ADVANCED SETUP 12 ABOUT ADVANCED OPERATION 16 WARRANTY 19 CAUTION Follow Installation Instructions before proceeding. SET THERMOSTAT TO MODE “OFF” PRIOR TO CHANGING SETTINGS IN SETUP OR RESTORING FACTORY DEFAULTS. Residential Light Commercial Systems Carrier Corporation 4/01 TSTATBBP2W01 Page 1
Summary of the content on the page No. 3
Front Panel I2:00 Mo 1 HEAT 72 70 3 2 5 4 1 Liquid Crystal Display with Thermoglow 2 Up/Down Buttons 3 On/Off Button 4 Outside Button 5 Heat or Cool Indicator Heat = Red, Cool = Green Page 2
Summary of the content on the page No. 4
Display 5 6 Night Am 2 4 Pm Setup I2:00 88 SuMoTuWeThFrSa COOL 1 8 Outside Locked 7 3 ONOFF Program On 1 HEAT 88 5 MorningDayEvening 4 88 1 Mode Indicators Selects the operation mode of the equipment. HEAT - indicates the heat mode. COOL - indicates the air conditioning mode. OFF - indicates the entire system is turned off. PROGRAM ON - indicates the stored program is enabled to run. Page 6. 2 Clock with Day of the Week Indicat
Summary of the content on the page No. 5
Display 5 Morning, Day, Evening & Night Indication Indicates the program time period. Page 8-11. 6 Setup Indication Indicates the thermostat is in the programming mode. Page 12. 7 Locked Indication Locked appears after the right combination of buttons are pressed, rendering the buttons inoperative. Page 16. 8 Outside Indication Outside temperature appears after pressing the Outside button if the thermostat is connected
Summary of the content on the page No. 6
Quick Start Set the Clock and Go Press the On/Off button. During Setup & Programming: While holding the On/Off ON/OFF Pressing the Mode button press the Outside button selects different flashing items. for 2 seconds to enter Setup (Represented in dark black) OUTSIDE screens. Pressing the Up and Down buttons will modify the flashing I2:00 I selection. To adjust the Press clock or Day use ON/OFF Su 2 buttons. Press both On/Off and ON/OFF Outside buttons as above to return to OUTSIDE nor
Summary of the content on the page No. 7
Basic Operation Select Mode I2:00 Su The HEAT setting indicates the temperature the room has to reach before the furnace will Press 70 turn on to heat the room. 69 ON/OFF I2:00 Su Program On will activate the stored timer operation. (Morning, Day, Evening, Night) 70 Day 70 Press ON/OFF I2:00 Su OFF indicates the heating system is turned off. OFF 70 NOTE: The operating mode of this thermostat may be changed from the factory default HEAT operation, to COOL operation in the Advanced Setup
Summary of the content on the page No. 8
Basic Operation Adjust the Select Desired Temperature desired Set Temperature I2:00 Pm with Mo HEAT 70 buttons. 69 Pressing the up/down buttons in Heat or Cool will adjust only the Heat or Cool set temperature. Outside This feature is only available if an optional wired, or wireless Outside Temperature Press Sensor is connected to the thermostat. OUTSIDE Pressing the Outside button will display the outside temperature. A subsequent press OUTSIDE of the Outside button will return the displ
Summary of the content on the page No. 9
Programming 4 Time periods Press the On/Off button. While holding the On/Off, press the Up button for 2 seconds to enter time period programming. ON/OFF Mo Select the Day of the Week. Press ON/OFF Am 6:00 Mo Adjust the start time for Morning. Press Morning ON/OFF Am 6:00 Mo Adjust the heating setpoint for Morning. (35 - 99 ) Press HEAT 70 Morning ON/OFF Continued Page 8
Summary of the content on the page No. 10
Programming 4 Time Periods Am 8:00 Mo Adjust the start time for Day. Press Day ON/OFF Am 8:00 Mo Adjust the heating setpoint for Day. (35 - 99 ) 62 HEAT Press Day ON/OFF 6:00Pm Mo Adjust the start time for Evening. Press Evening ON/OFF Continued Page 9
Summary of the content on the page No. 11
Programming 4 Time Periods 6:00Pm Mo Adjust the heating setpoint for Evening. (35 - 99 ) 70 HEAT Evening Press ON/OFF Night I0:00Pm Mo Adjust the start time for Night. Press ON/OFF Night I0:00Pm Mo Adjust the heating setpoint for Night. (35 - 99 ) Press HEAT 62 ON/OFF Continued Page 10
Summary of the content on the page No. 12
Programming 4 Time Periods Copy Command No Yes Select Yes to copy the stored Tu program to the next day. Press Select No to continue manually Co storing the time period No ON/OFF Py programming for the next day. If NO was selected above, Continue Time Period Programming Morning through Night as done in previous steps starting on page 8 for the next day’s schedule. To Exit Programming Press the On/Off button. While holding the On/Off, press the Up button to exit time period prog
Summary of the content on the page No. 13
Advanced Setup Press the On/Off button. ON/OFF While holding the On/Off, NOTE: Each step # is located at press the Outside button the top right corner of the for 10 seconds to enter Setup display for easy reference. OUTSIDE screens. Am I2:00 Setup I Adjust the time of day clock. Tip: To change hours quickly, press and Press hold the Outside button in and press the up or down buttons. ON/OFF Mo Setup 2 Select the day of the week. Press ON/OFF COOL Setup
Summary of the content on the page No. 14
Advanced Setup ON Setup 4 Select the operation of the thermostat: ON is 7-day programmable, ON OFF is non-programmable Program OFF Press ON/OFF 8sp Setup 5 Configure the display. 1 = setpoint only 2 = room temperature with setpoint. 2 Press ON/OFF Setup 6 Adjust the deadband from 1 - 6 degrees. 2 Press 88 ON/OFF Select the cycles per hour limit. Setup 7 d=cycles per hour limit defeated. d1=d + defeat 5 min. Compressor lockout, lockout is for Cool operation. 6 Press Cy
Summary of the content on the page No. 15
Advanced Setup C Setup 8 Select thermostat operation in degrees Fahrenheit or Centigrade. Press F F ON/OFF On Setup 9 Select the display back- light always On, or Off after 8 seconds. ON ON/OFF Off L I OUTSIDE Press the On/Off button. While holding the On/Off press the outside button to leave the Setup screens. If no buttons are pressed, the display will leave the setup screens after 60 seconds. Page 14
Summary of the content on the page No. 16
Advanced Setup Advanced Setup Table Step # Description Range Factory Default 1 Time of day clock set 24 hour 12:00 Am 2 Day of the week Sun - Sat Monday 3 Operating Mode - Heat or Cool Heat / Cool Heat 4 Programmability flag On /
Summary of the content on the page No. 17
About Advanced Features & Operation KEYPAD LOCK - To prevent unauthorized use of the thermostat, the front panel buttons may be disabled. To disable, or ‘lock’ the keypad, press and hold in the On/Off button. While holding the On/Off button in, press the Up and Down buttons in together. The Locked icon will appear on the display. Am I2:00 Su Locked Press all 3 for Keypad Lockout HEAT 70 ON/OFF 55 To unlock the buttons, again press a
Summary of the content on the page No. 18
About Advanced Features & Operation OPTIONAL LOCKING COVER I2:00 I2:00 Mo Mo HEAT HEAT 72 72 70 70 Page 17
Summary of the content on the page No. 19
About Advanced Features & Operation TWO-WIRE THERMOSTAT INSTALLATION WIRING Two-Wire Thermostat L L R W1 Resistor (If Required) C HVAC Equipment If the Two-Wire thermostat is losing time or showing PF or P- it may be neccessary to install the 10 watt 250 ohm resistor that is supplied with the thermostat. Page 18 RS+5 RS 250 OHM 10 WATT RS GND
Summary of the content on the page No. 20
STEP #1 PREPARATION Proper installation of the thermostat will be accomplished by following these step by step instructions. If you are unsure about any of these steps, call a qualified technician for assistance. Assemble tools as shown below. Drill with 3/16 inch Drill Bit (when not using Flat Blade Wire cutter j-box) Screwdriver & Stripper Make sure your Heater/Air Conditioner is working properly before beginning installation of the thermostat. Carefully unpack the thermostat. Save the scr
