Summary of the content on the page No. 1
N
T
Installation
Instructions
T050.541
3/4" CLASSIC THERMOSTAT TRIM KIT
with SEPARATE VOLUME CONTROL
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
Certified to comply with ANSI A112.18.1M
ASSE 1016
M968419 REV 1.1
ROUGHING-IN DIMENSIONS
6
9-1/2"
4"
Recommended Tools
Phillips Screwdriver
Flat Blade Screwdriver
CARE INSTRUCTIONS:
Remove as m
Summary of the content on the page No. 2
N N TRIM INSTALLATION 4 1 1 7 2 Remove PLASTER GUARD (1). 5 Remove HANDLE SCREW and ADAPTER (7) from rough valve. Push CAPS (2 & 3) as shown onto CONTROL VALVES (4). 7 Push ESCUTCHEON (5) onto CAPS (2 & 3) and attach with (60mm) SCREWS (6) to valve. Push COVER PLATE (7) onto CAPS (2 & 3) and snap into holes in ESCUTCHEON (5) to secure. 3 6 1 INSTALL HANDLES 2 Install HANDLE ADAPTER (1) onto VOLUME CONTROL SPLINE (2). 2 Align CROSS HANDLE (3) and push onto HANDLE ADAPTER (1). 1 3 Install HANDLE
Summary of the content on the page No. 3
N N TEMPERATURE ADJUSTMENT 4 Pull out INDEX BUTTON (1) and remove LEVER HANDLE SCREW (2). Pull off LEVER HANDLE ASSEMBLY (3). Check that arrow marking B points to the 3 o'clock position. If not, push the BLACK CLAMP on the SECURING RING to the right, pull off KNOB MOUNT (4) and reinstall KNOB MOUNT (4) with arrow "B" 3 o'clock position. See Figure 1. SET HOT LIMIT STOP The maximum mixed water temperature is set at 109 F at the factory. This setting can be changed if desired. Remove the TEMPERAT
Summary of the content on the page No. 4
N T 3/4" CLASSIC THERMOSTAT TRIM KIT with SEPARATE VOLUME CONTROL MODEL NUMBER T050.541 M907093-YYY0A VOLUME CAP M962365-YYY0A ESCUTCHEON M909625-YYY0A FRONT COVER PLATE 918049-0070A HANDLE ADAPTER A908593-YYY0A VOLUME CONTROL HANDLE 918428-0070A VOLUME HANDLE SCREW A954049-YYY0A VOLUME HANDLE CAP 907090-YYY0A TEMPERATURE CAP A954043-YYY0A 918434-YYY0A TEMPERATURE HANDLE CAP ESCUTCHEON SCREWS 918416-0070A TEMPERATURE M961112-YYY0A HANDLE SCREW TEMPERATURE CONTROL HANDLE Replace the "YYY" with
Summary of the content on the page No. 5
Installation Instructions R520 CENTRAL THERMOSTAT WITH VOLUME CONTROL Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. Certified to comply with ANSI A112.18.1M To ensure that your installation proceeds smoothly--please ASSE 1016 read these instructions carefully before you begin. M968255Rev.1.1 ROUGHING-IN DIMENSIONS CONNECTIONS ARE: 1/2" NPT 6-1/4 1/2" NPT SHOWER 3-15/16 7 3-5/8 1/2" NPT INLET 1/2" NPT 1/2" NPT INLET TUB 1-5/8 - 2-1/2 5-7/8 THERMOSTA
Summary of the content on the page No. 6
DO NOT SOLDER DIRECTLY TO THE VALVE BODY; THIS WILL DAMAGE WARNING ROUGHING-IN THE VALVE THE TEMPERATURE CONTROL ELEMENT AND CHECK STOP VALVES. 1 MIXED COLD Prepare water supplies per ROUGHING-IN DIMENSIONS. Make sure the finished wall is between the minimum and maximum rough dimension. Install VALVE at indicated height and depth. Make sure the "TOP" marking on the PLASTER GUARD is up. Connect the hot and cold water supplies. Assemble all connecting pipes. Flush lines to HOT remove any dirt. Conn
Summary of the content on the page No. 7
CENTRAL THERMOSTAT WITH VOLUME CONTROL MODEL NUMBER R520 953950-0070A CHECK STOP (COLD BLUE) 994053-0070A CARTRIDGE A918572-0070A CARTRIDGE SCREW 923348-0070A HANDLE ADAPTER 953963-0070A 953960-0070A HANDLE EXTENSION THERMOSTAT CARTRIDGE 953951-0070A 912647-0070A CHECK STOP (HOT RED) 953957-0070A O-RING TEMPERATURE CALIBRATION UNIT 963434-YYY0A DEEP ROUGH KIT (SOLD SEPARATELY) HOT LINE FOR HELP For toll-free information and answers to your questions, call: 1-800 442-1902 Weekdays 8:00 a.m. to 8
Summary of the content on the page No. 8
DO NOT SOLDER DIRECTLY TO THE VALVE BODY; THIS WILL DAMAGE MIXED WARNING ROUGHING-IN THE VALVE THE TEMPERATURE CONTROL ELEMENT AND CHECK STOP VALVES. Installation 1 Instructions COLD Prepare water supplies per ROUGHING-IN DIMENSIONS. Make sure the finished wall is between the minimum and maximum rough dimension. 3/4" CENTRAL THERMOSTAT R540 Install VALVE at indicated height and depth. Make sure the "TOP" marking on the PLASTER GUARD is up. WITH VOLUME CONTROL Connect the hot and cold water suppli
Summary of the content on the page No. 9
DO NOT SOLDER DIRECTLY TO THE VALVE BODY; THIS WILL DAMAGE MIXED WARNING ROUGHING-IN THE VALVE THE TEMPERATURE CONTROL ELEMENT AND CHECK STOP VALVES. Installation 1 Instructions COLD Prepare water supplies per ROUGHING-IN DIMENSIONS. Make sure the finished wall is between the minimum and maximum rough dimension. 3/4" CENTRAL THERMOSTAT R540 Install VALVE at indicated height and depth. Make sure the "TOP" marking on the PLASTER GUARD is up. WITH VOLUME CONTROL Connect the hot and cold water suppli
Summary of the content on the page No. 10
DO NOT SOLDER DIRECTLY TO THE VALVE BODY; THIS WILL DAMAGE MIXED WARNING ROUGHING-IN THE VALVE THE TEMPERATURE CONTROL ELEMENT AND CHECK STOP VALVES. Installation 1 Instructions COLD Prepare water supplies per ROUGHING-IN DIMENSIONS. Make sure the finished wall is between the minimum and maximum rough dimension. 3/4" CENTRAL THERMOSTAT R540 Install VALVE at indicated height and depth. Make sure the "TOP" marking on the PLASTER GUARD is up. WITH VOLUME CONTROL Connect the hot and cold water suppli
