American Standard CERATHERM T050110 user manual

Summary of the content on the page No. 1

60
Installation
Instructions
T050110
T050120
CENTRAL THERMOSTAT
LESS VOLUME CONTROL
TRIM KIT
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
Certified to comply with ANSI A112.18.1M
To ensure that your installation proceeds smoothly--please ASSE 1016
read these instructions carefully before you begin.
M968265
ROUGHING-IN DIMENSIONS
6-11/16"
C
L
100
9-1/8"
FINISHED
1-11/16" to 2-1/2"
WALL
Recommended Tools
Phillips Screwdriver
Flat Blade Screwdriver
C

Summary of the content on the page No. 2

100 TRIM INSTALLATION 1 1 2 Push CAP (1) over the O-RING SEAL (2). 3 5 Push ESCUTCHEON HOLDER (3) with lightly greased O-RING SEAL (4) over CAP (1). Push on ESCUTCHEON (5) and attach with (60mm) SCREWS (6) to valve body. GREASE ESCUTCHEON 4 HOLDER O-RING SEAL 6 HANDLE INSTALLATION 2 1 Push TEMPERATURE-CONTROL KNOB (1) (with the red stop on top) 3 onto KNOB MOUNT (2). 4 5 Install HANDLE RING (3) and tighten CONTROL KNOB (1) with HANDLE RING (3) in place using HANDLE SCREW (4). Install KNOB CAP (5

Summary of the content on the page No. 3

CENTRAL THERMOSTAT LESS VOLUME CONTROL TRIM KIT MODEL NUMBERS T050110 T050120 918327-0070A ESCUTCHEON CARRIER SCREWS 953961-0070A ESCUTCHEON 953947-YYY0A CARRIER ESCUTCHEON 953976-YYY0A TEMPERATURE CONTROL HANDLE BASE 909750-YYY0A HANDLE RING 907090-YYY0A CAP 918416-0070A SCREW 907065-YYY0A HANDLE CAP 913981-0070A SEAL 060441-YYY0A 918378-YYY0A TEMPERATURE ESCUTCHEON SCREWS CONTROL HANDLE Replace the "YYY" with appropriate finish code CHROME 002 HOT LINE FOR HELP POLISHED BRASS 099 For toll-free

Summary of the content on the page No. 4

Installation Instructions R510 R530 ROUGH VALVE KIT CENTRAL THERMOSTAT LESS VOLUME CONTROL Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. Certified to comply with ANSI A112.18.1M ASSE 1016 To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. M968256A ROUGHING-IN DIMENSIONS 1/2" NPT OUTLETS FOR R510 1/2" NPT OUTLETS FOR R510 3/4" NPT OUTLETS FOR R530 3/4" NPT OUTLETS FOR R530 5-7/8" 3-3/8" 3

Summary of the content on the page No. 5

ROUGHING-IN THE VALVE Turn off hot and cold water 1 CAUTION supplies before beginning. Prepare water supplies per ROUGHING-IN DIMENSIONS. Make sure the finished wall is between the minimum 1-11/16" and maximum 2-1/2" rough dimension. Install VALVE (1) at indicated height and depth. Make sure the "TOP" marking on the PLASTER GUARD (2) is up. For support, use pipe BRACES (3) secured to wooden braces. COLD Connect the hot and cold water supplies. Assemble all connecting pipes. Close off the tub por

Summary of the content on the page No. 6

CENTRAL THERMOSTAT LESS VOLUME CONTROL MODEL NUMBERS 953950-0070A CHECK STOP R510 R510 (COLD BLUE) R530 A953971-0070A CHECK STOP R530 (COLD BLUE) A954820-0070A THERMOSTAT CARTRIDGE R510 954040-0070A THERMOSTAT CARTRIDGE R530 953963-0070A HANDLE EXTENSION 953951-0070A CHECK STOP R510 (HOT RED) A953972-0070A CHECK STOP R530 (HOT RED) 912647-0070A O-RING 963434-0020A DEEP ROUGH KIT SOLD SEPARATELY 953957-0070A TEMPERATURE CALIBRATION UNIT HOT LINE FOR HELP For toll-free information and answers to